Nokia RH-37 Series Installation instructions

Nokia Customer Care
RH-37 Series Transceivers
Issue 1 07/04 2004 Nokia Corporation Page 1
Company Confidential
5 - Disassembly Instructions

RH-37
5 - Disassembly Instructions Nokia Customer Care
Page 2 Nokia Corporation Issue 1 07/04
[This page left intentionally blank]

Nokia Customer Care 5 - Disassembly Instructions
RH-37
Issue 1 07/04 Nokia Corporation Page 3
Table of Contents
Page No
Disassembly Instructions....................................................................................................................... 5
General requirements ..........................................................................................................................5
Detailed disassembly instructions ...................................................................................................6
Dome Sheet Placement....................................................................................................................... 11
Cleaning ................................................................................................................................................11
Placing the dome sheet to the light guide ..................................................................................11
Placing the light guide assembly onto the PWB .......................................................................13

RH-37
5 - Disassembly Instructions Nokia Customer Care
Page 4 Nokia Corporation Issue 1 07/04
[This page left intentionally blank]

Nokia Customer Care 5 - Disassembly Instructions
RH-37
Issue 1 07/04 Nokia Corporation Page 5
Disassembly Instructions
General requirements
Use the correct ESD protection before handling the RH-37 product.
Use gloves to handle the RH-37 product.
Required tools:
• torx 6 screwdriver, for disassembly
• torx 6 torque-driver, set to 28Ncm torque for reassembly
• slotted screwdriver
• tweezers
• SS-42 camera removal tool
• SRT-6 opening tool
•DC-plug
Note: When shielding lids are removed from the shielding frames of the PWB, new lids must be used
in order to close the shielding properly. It is not allowed to re-use the removed ones.

RH-37
5 - Disassembly Instructions Nokia Customer Care
Page 6 Nokia Corporation Issue 1 07/04
Detailed disassembly instructions
Needed tools for disassembly. Protect the Window with a plastic film.
Press the C-Cover Lock before pulling the C-Cover. Protect the Camera Window with a plastic film.
Lift the topside of the A-Cover and then remove it care-
fully.
Also protect the inner side of A-Cover with a plastic film.

Nokia Customer Care 5 - Disassembly Instructions
RH-37
Issue 1 07/04 Nokia Corporation Page 7
Remove Keymat. Unscrew the six Torx Plus®size 6 screws. For assembly, the
reverse order and a Torx Plus®driver with a torque of
28Ncm has to be used.
Separate the Modules from B-Cover. Open the LCD Connector with SRT-6 carefully.
Use SRT-6 to separate the LCD-Module from UI-Shield. Protect the LCD-Module with a plastic film.
623
514

RH-37
5 - Disassembly Instructions Nokia Customer Care
Page 8 Nokia Corporation Issue 1 07/04
When changing the Light Guide Assy use SRT-6 as a lever.
Keep in mind that Dome Sheet is glued to the Engine
Module.
Put the Engine Module into the Soldering Jig.
Use a slotted screwdriver as a lever to open the Camera
Shield.
Camera Module is attached with four double snaps into its
guidance.
Place the removal tool as shown in the picture and unlock
the snaps on both sides. Note releasing order.
Remove the Camera Module with the removal tool as
shown in the picture.

Nokia Customer Care 5 - Disassembly Instructions
RH-37
Issue 1 07/04 Nokia Corporation Page 9
All Gel Grips are attached to the B-Cover with hooks.
Slide the Gel Grip as shown in the picture to unlock the
hooks.
The numeric characters of the Grips are for place identifi-
cation only.
Use the DC-Plug to remove the DC-Connector. Tweezers can be used to remove the Microphone.
Tweezers can also be used to remove the Vibra Motor. Push down the clip of the IHF Lid Assy to release the Lid
and the Power Key.

RH-37
5 - Disassembly Instructions Nokia Customer Care
Page 10 Nokia Corporation Issue 1 07/04
Note: If a new B-cover is used, a torque setting of 28Ncm and speed in the range of 400 - 600 rpm is
required to cut the new thread.
Caution: The display connector is fragile. Movement of the display module/UI shield assembly can
damage the solder joints of connector on the display module or phone PWB. Ensure it is held in place
during unscrewing and screwing.
The parts drop out easily. IHF Speaker can be removed with tweezers. Note the guid-
ing pin while re-assembling.
Push out the Blind Plug by using a screwdriver.