Nokia BH-804 - Headset - Over-the-ear User manual

© 2010 Nokia. All rights reserved.
Nokia Bluetooth Headset BH-804
9218865
Issue 1.0
8
6
7
5
2
34
1
11
12
10
9

© 2010 Nokia. All rights reserved.
13
14
15
16
17
18
19

© 2010 Nokia. All rights reserved. 3
DECLARATION OF CONFORMITY
Hereby, NOKIA CORPORATION declares
that this BH-804 product is in
compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC. A
copy of the Declaration of Conformity
can be found at http://www.nokia.com/
phones/declaration_of_conformity/.
© 2010 Nokia. All rights reserved.
Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
Introduction
With the Nokia Bluetooth Headset
BH-804, you can make and answer
calls hands-free with your
compatible mobile device.
Read this user guide carefully
before using the headset. Also,
read the user guide for the device
that you connect to the headset.
The surface of this device does not
contain nickel in the platings. The
surface of this device contains
stainless steel.
Bluetooth wireless technology
The headset is compliant with the
Bluetooth Specification 2.0 + EDR
supporting the Headset Profile 1.1
and Hands-Free Profile 1.5. Check
with the manufacturers of other
devices to determine their
compatibility with this device.

4
4 © 2010 Nokia. All rights reserved.
Get started
The headset contains the
following parts shown on the title
page: earpiece (1), indicator light
(2), volume keys (3), multifunction
key (4), earloop holder (5), earloop
(6), microphone (7), and charging
contacts (8).
Before using the headset, you
must charge the battery and pair
the headset with a compatible
device.
Compatible chargers
This device is intended for use
when supplied with power from the
following chargers: AC-6 and DC-6.
The exact charger model number
may vary depending on the type of
plug. The plug variant is identified
by one of the following: E, EB, X,
AR, U, A, C, or UB.
Charge the battery
1. Connect the charger to a wall
outlet.
2. To charge the headset in the
desk stand (if provided with the
headset), connect the charger
cable to the charger connector
at the side of the desk stand
(9), and place the lower end of
the headset into the slot on the
desk stand (10). The headset
switches off.
To charge the headset using the
charger adapter (if provided
with the headset), connect the
charger cable to the charger
connector on the adapter (11),
and insert the lower end of the
headset into the adapter (12).
The headset switches off. To
keep the adapter attached to

© 2010 Nokia. All rights reserved. 5
the charger cable, push the
cable into the slot on the
adapter.
The red indicator light is
displayed during charging.
Charging the battery fully may
take up to 1 hour with the AC-6
or DC-6 charger.
3. When the battery is fully
charged, the green indicator
light is displayed. Remove the
headset from the desk stand,
or remove the adapter.
4. Disconnect the charger from
the wall outlet.
The battery can also be charged
through the USB port of a
compatible computer using the
Nokia Connectivity Cable CA-101
(sold separately). Connect one end
of the cable to the desk stand or
charger adapter and the other end
to the USB port on the computer.
The fully charged battery has
power for up to 4 hours of talk
time or up to 150 hours of standby
time.
When the battery charge is low,
the headset beeps about every
minute, and the red indicator light
flashes.
Switch on or off
To switch on, press and hold the
multifunction key for about
2 seconds. The headset beeps,
and the green indicator light is
displayed. The headset first tries to
connect to the last used mobile
device and then, if the connection
fails, to one of the other paired
devices. When the headset is
connected to a device and is ready
for use, the blue indicator light
flashes slowly. If the headset has
not been paired with a device, it

6
6 © 2010 Nokia. All rights reserved.
automatically enters pairing
mode.
To switch off, press and hold the
multifunction key for about 4
seconds. The headset beeps, and
the red indicator light is briefly
displayed. If the headset is not
connected to a device within
about 30 minutes, it switches off
automatically.
Pair and connect the headset
Before using the headset, you
must pair and connect it to a
compatible device.
1. Ensure that your mobile device
is switched on and the headset
is off.
2. If the headset has not been
previously paired with a device,
switch on the headset. The
headset enters pairing mode,
and the blue indicator light
starts to flash quickly.
If the headset has been
previously paired with a device,
ensure that the headset is
switched off, and press and
hold the multifunction key (for
about 4 seconds) until the blue
indicator light starts to flash
quickly.
3. Activate the Bluetooth feature
on your device, and set it to
search for Bluetooth devices.
For details, see the user guide
of your mobile device.
4. Select the headset from the list
of found devices.
5. If necessary, enter the passcode
0000 to pair and connect the
headset to your device.
In some devices, you may need
to make the connection
separately after pairing.

© 2010 Nokia. All rights reserved. 7
If pairing is successful, the headset
appears in the menu of the mobile
device where you can view the
currently paired Bluetooth
devices.
When the headset is connected to
your device and is ready for use,
the blue indicator light flashes
slowly.
To disconnect the headset from
your mobile device, switch off the
headset, or disconnect it in the
Bluetooth menu of the device.
If you disconnect the headset from
your mobile device, you can
reconnect the headset to the
device without switching the
headset off and back on. Press and
hold the multifunction key for
about 2 seconds, or make the
connection in the Bluetooth menu
of your device.
You may be able to set your device
so that the headset connects to it
automatically. To activate this
feature in a Nokia device, change
the paired device settings in the
Bluetooth menu.
Basic use
Place the headset on the ear
The headset is provided with an
earloop that you can use for a
better fit on your ear.
To use the headset without the
earloop, gently push the earpiece
into your ear (13), and point the
headset toward your mouth.

8
8 © 2010 Nokia. All rights reserved.
To use the headset with the
earloop, insert the earloop holder
into the slot at the base of the
earpiece (14), and insert the
earloop into the opening on the
holder (15). To wear the headset
on the right ear, rotate the earloop
so that the loop is to the right of
the Nokia logo. Slide the earloop
over your ear (16), and push or pull
the earloop to set its length.
Gently push the earpiece into your
ear, and point the headset toward
your mouth (17).
To use the headset on the left ear,
rotate the earloop so that it is to
the left of the Nokia logo (18).
To detach the earloop, gently pull
it from the headset.
Carry the headset in the
strap
The headset may be provided with
a carrying strap. You can use the
strap to wear the headset around
your neck.
To attach the headset to the strap,
insert the headset into the catch
at the end of the strap (19).
To detach the headset, pull it from
the catch.
Calls
To make a call, use your mobile
device in the normal way when the
headset is connected to it.
To redial the number you last
called (if your mobile device
supports this feature with the
headset), when no call is in
progress, press the multifunction
key twice.
To activate voice dialling (if your
mobile device supports this
feature with the headset), when
no call is in progress, press and
hold the multifunction key for

© 2010 Nokia. All rights reserved. 9
about 2 seconds. Proceed as
described in the user guide of the
mobile device.
To answer or end a call, press the
multifunction key. To reject a call,
press this key twice.
To adjust the headset volume,
press either volume key.
To switch a call from the headset
to a connected device, press and
hold the multifunction key for
about 4 seconds (the headset
switches off), or use the keys of
your device. To switch the call
back to the headset, switch on
the headset, or press and hold the
multifunction key for about 2
seconds (when the headset is
switched on).
Clear settings or reset
To clear all the pairing settings
from the headset, switch off the
headset, and press and hold the
multifunction key (for over 8
seconds) until the red, green, and
blue indicator lights start to
alternate. After the settings are
cleared, the headset enters pairing
mode.
To reset the headset if it stops
functioning, even though it is
charged, connect the headset to a
charger that is plugged into a wall
outlet. The reset does not clear the
pairing settings.
Troubleshooting
If you cannot connect the headset
to your compatible device, check
that the headset is charged,
switched on, and paired with the
device.