Norac UC5 Topcon X30 User manual

Spray Height
C
ontroller
John Deere
GS2
2600 and 1800
All Pull Types Display Kit
Installation Manual
GS2
-
PT01

Printed in Canada
Copyright 2010 by NORAC Systems International Inc.
Reorder P/N: 54VT-GS2-PT01-INST Rev A (John Deere GS2 2600 and 1800 All Pull Types
Display Kit)
NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without
the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information contained in this
manual. The technical information in this manual was reviewed at the time of approval for publication.

1
Contents
1INTRODUCTION...................................................................................................2
1.1 List of Parts....................................................................................................................................... 2
2INSTALLATION ....................................................................................................3
2.1 Control Module on Tractor................................................................................................................. 3
2.2 Control Module on Sprayer................................................................................................................ 4
2.3 Switch Box Installation...................................................................................................................... 5
3CABLE DRAWINGS..............................................................................................6
3.1 ITEM C25: 44602-01 – SWITCH REMOTE HAND CONTROL...................................................... 6
3.2 ITEM C26: 43240-26 – CABLE UC5 SWITCH BOX....................................................................... 7
3.3 ITEM C30: 43250-06 – CABLE UC5 BATTERY PIGTAIL............................................................. 8
3.4 ITEM C41: 43220-03 - CABLE UC5 NETWORK 14 AWG - 3M...................................................... 8
3.5 ITEM C40: 43260-02 – CABLE UC5 CAN BUS VT JD GS2 ........................................................... 9
APPENDIX A: ALTERNATE CONFIGURATION ................................................10

2
1 Introduction
The John Deere GS2 2600 and 1800 – All Pull Types Display Kit Manual is intended to be used
in conjunction with the UC5 Spray Height Control Installation Manual. This manual provides
instructions to interface the UC5 Control Module to the John Deere GS2 2600 and 1800
Displays. For installation of the rest of the UC5 Spray Height Control System please refer to the
sprayer specific manual provided with the kit.
1.1 List of Parts
Item Part Number Name Quantity
C25 44602-01 BOX SWITCH UC4 REMOTE HAND CONTROL VER.1 RMR 1
C26 43240-26 CABLE UC5 SWITCH BOX 1
C30 43250-06 CABLE UC5 BATTERY PIGTAIL (FUSED) 1
C40 43260-02 CABLE UC5 CAN BUS VT JD GS2 1
C41 43220-03 CABLE UC5 NETWORK 14 AWG 3M 1
E12 43764 UC5 NETWORK COUPLER 2-WAY 1
M01 UC5-BC-MANUAL - NS MANUAL UC5 OPERATORS - NORAC 1
M04 54VT-GS2-PT01-INST MANUAL UC5 DISPLAY KIT JOHN DEERE GS2 2600 & 1800 - ALL PULL TYPES 1

3
2 Installation
The following instructions are for installation on a pull type sprayer. On a pull type sprayer if
the CAN-bus and power supply are located on the sprayer, the control module may also be
installed on the sprayer (Section 2.2). This type of installation would eliminate the need for a
cable across the hitch.
2.1 Control Module on Tractor
1. Securely mount the control module (E01) inside the tractor cab.
2. Tee the CAN-bus interface cable (C40) in to the John Deere CAN-bus. Connect the 6 pin
Deutsch plug on cable C40 to the end of the control module with only one Deutsch
connector.
3. Connect cable C41 to the other CAN-bus connector and route the cable to the hitch of the
tractor.
4. Connect the two-way coupler (E12) to the end of cable C41.
5. Connect cable C01 to the coupler (E12) and route towards the rear of the sprayer. The two-
way coupler (E12) will provide the hitch disconnect.
Figure 1: GS2 2600 Display Kit – Control Module on Tractor

4
2.2 Control Module on Sprayer
1. Securely mount the control module (E01) on the sprayer near the CAN-bus connection.
2. Tee the CAN-bus interface cable (C40) in to the John Deere CAN-bus. Connect the 6 pin
Deutsch plug on cable C40 to the end of the control module with only one Deutsch
connector.
Figure 2: GS2 2600 Display Kit – Control Module on Sprayer

5
2.3 Switch Box Installation
1. This step of the installation assumes that the input module and all required cables are
installed.
2. Disconnect cable C20 (Thru 2 connector) from the Input Module (E03). Remove the wedge
from the face of the 12 pin Deutsch plug. The wedge is removed by inserting a small flat
implement underneath the wedge and lifting it up.
3. Insert the Roll CW pin from C26 into position 3 of the 12 pin plug on C20. Insert the Roll
CCW pin from C26 into position 4 of the 12 pin plug on C20. Insert the wedge back into the
plug. Connect C20 to the Thru 2 connector on the Input Module.
4. Connect the 12 pin Deutsch plug on C26 to the OEM 3 connector on the input module.
Route the other end of the cable to the hitch of the sprayer.
5. Attach the switch box (C25) inside the cab and connect it to cable C26. An extra label is
provided with the switch box if you prefer to remove the switches from the housing and
mount them in the existing sprayer switch panel.
* Some sprayer types may not use all the switch functions.
* Refer to “Appendix A” for sprayers with European style slant control.
Figure 3: Switch Box Installation

6
3 Cable Drawings
3.1 ITEM C25: 44602-01 – SWITCH REMOTE HAND CONTROL

7
3.2 ITEM C26: 43240-26 – CABLE UC5 SWITCH BOX

8
3.3 ITEM C30: 43250-06 – CABLE UC5 BATTERY PIGTAIL
3.4 ITEM C41: 43220-03 - CABLE UC5 NETWORK 14 AWG - 3M

9
3.5 ITEM C40: 43260-02 – CABLE UC5 CAN BUS VT JD GS2

10
Appendix A: Alternate Configuration
If your sprayer has European style slant control, you will need to reconfigure the switch box as
shown below. This is only required for sprayer types which are driving the slant output from the
Input Module. Reconfigure the pins on cable C26 and C20 as follows:
Connector Pin Location Connector Pin Location
Power White OEM 3 (C26) 1 OEM 3 (C26) 1
Ground Black OEM 3 (C26) 12 OEM 3 (C26) 12
Remote Auto Brown OEM 3 (C26) 11 OEM 3 (C26) 11
Remote Manual Blue OEM 3 (C26) 10 Thru 2 (C20) 4
Main Up Purple OEM 3 (C26) 9 OEM 3 (C26) 9
Main Down Yellow OEM 3 (C26) 8 OEM 3 (C26) 8
Roll CW Red Thru 2 (C20) 3 OEM 3 (C26) 6
Roll CCW Orange Thru 2 (C20) 4 OEM 3 (C26) 10
European Style Slant Configuration
Wire Color
Function
(Cable C26)
Normal Configuration

Canada
NORAC Systems International Inc.
Phone: [phone]
Toll Free: 1 800 667 3921
Shipping Address:
3702 Kinnear Place
Saskatoon, SK
S7P 0A6
United States
NORAC, Inc.
Phone: [phone]
Toll Free: 1 866 306 6722
Shipping Address:
1290 Osborne Rd NE, Suite F
Fridley, MN
55432-2892
Europe
NORAC Europe
Phone: [phone]
Shipping Address:
Rue de l’hermitage
01090 GUEREINS
France
www.norac.ca