Nordson Rhino SD3 User manual

Instruction Sheet
Part 1610314−03
E2018 Nordson Corporation
P/N 1610314−03
RhinorSD3/XD3 Single-Post Container
Hold-Down
WARNING: Allow only qualified personnel to perform the following tasks. Follow
the safety instructions in this document and all other related documentation.
Description
See Figure 1. The RhinorSD3/XD3 container hold-down is used to secure the
material container in place during a container change.
10016501
Container Hold-Down
Figure 1 Container Hold-Down

RhinorSD3/XD3 Container Hold-Down
2
Part 1610314−03 E2018 Nordson Corporation
Installation
See Figure 2.
1. Remove the two locating discs (3).
2. Align the container hold-down assembly to the threaded holes (4) on the base
plate (5).
3. Use the screw (1) and washer (2) to secure the locating disc (3) to the
container hold-down assembly bracket and base plate (5). Tighten to
18 ft-lb (24 NSm).
4. Use the six screws (6) included in the container hold-down kit to secure the
container hold-down to the base plate (5). Tighten to 18 ft-lb (24 NSm).
10015733
1
2
3
54
6
Figure 2 Container Hold-Down Installation

3
RhinorSD3/XD3 Container Hold-Down
Part 1610314−03
E2018 Nordson Corporation
Adjustment
See Figure 3.
NOTE: Ensure the locating discs are installed and adjusted properly for the
material container size.
1. Loosen the four screws (2) on the side brackets (3) on either side of the
container hold-down assembly.
2. Raise the container hold-down assembly to its highest position.
3. Temporarily tighten the four screws (2) to keep the container hold-down
assembly elevated.
4. Load material container on the base plate beneath the container hold-down
assembly.
5. Ensure the bails of the material container are aligned directly below the lateral
adjustment bracket (4).
6. Lower the container hold-down assembly until the lateral adjustment
bracket (4) is slightly above the material container bails.
7. Tighten the four screws (2) on the side bracket (3) to 7 ft-lb (9.5 NSm).
8. Loosen the four screws (1) and adjust the lateral adjustment bracket (4) until it
it almost touches the material container.
9. Tighten the four screws (1) to 7 ft-lb (9.5 NSm).
10015733
1
2
4
3
Figure 3 Container Hold-Down Adjustment

RhinorSD3/XD3 Container Hold-Down
4
Part 1610314−03 E2018 Nordson Corporation
Parts
To order parts, call the Nordson Industrial Coating Systems Customer Support
Center at [phone] or contact your local Nordson representative.
See Figure 4 and refer to the following parts list.
10015733
2
3
56
7
9
8
1
11
10
4
Figure 4 Container Hold-Down
Item Part Description Quantity Note
— 1612241 KIT, container, hold-down, Rhino, 5 gal, blue 1
— 1613413 KIT, container, hold-down, Rhino, 5 gal, red 1
1−−−−−− SSCREW, button head, M8 x 18 mm, steel, zinc,
Class 10.9, per ISO 7380 6
2−−−−−− SBRACKET, upper, hold-down 1 A
3−−−−−− SSCREW, button head, socket, M6 x 14, zinc,
Class 10.9, per ISO 7380 4
4−−−−−− SWASHER, flat, M6, steel, zinc, per DIN 125 4
5−−−−−− SSCREW, flat, socket, M6 x 14, zinc 4
6−−−−−− SBRACKET, left, lower, hold-down 1 A
7−−−−−− SSCREW, button, socket, cap, M6 x 16, zinc,
Class 10.9, per ISO 7380 4
8−−−−−− SBRACKET, lateral adjustment, hold-down 2 A
9−−−−−− SBRACKET, mounting plate, hold-down 2 A
10 −−−−−− SBRACKET, vertical adjustment, hold-down 2 A
11 −−−−−− SBRACKET, right, lower, hold-down 1 A
NS 900464 SADHESIVE, LoctiterThreadlocker Blue 242r,
removable, 50 m AR
NOTE A: Part is available in blue or red.
AR: As Required
NS: Not Shown
Issued 7/18
Original copyright date 2018. Rhino, Nordson, and the Nordson logo are registered trademarks of Nordson Corporation.
All other trademarks are the property of their respective owners.