norix Oasis Classroom Table User manual

B
A
C
C
C
J
K
H
H
L
D
E
F
G
Step 1:
Place Table Top on protected surface. Attach Leg Frame to
Table Top using (8) 5/16-18 x 1" Screws( F ),
(8) 5/16 Lock Washers( E ), and (8) 11/32 Flat Washers( D ).
Step 2:
Attach Leg to Table Top using
(4) 5/16-18 x 1 1/4" Screws( G ).
Repeat for other Legs.
Tools Needed
Low RPM Variable Speed Drill
5/8" Magnetic Deep Socket
1/4" Hex Driver
Rubber Mallet
24" Socket Extension
3/8" Concrete Drill Bit
PARTS LIST
ITEM QTY PART NUMBER DESCRIPTION
A 1 033-3206-XX Oasis Classroom Table Frame
B 1 053-3072-MA-YYZZZ-J Top, Oasis, 30x72, Juvenile Class, Laminate Top, Molded-Edge
C 3 033-3205-XX Oasis Bolt Down Leg
D 8 026-006 Washer, Flat, 11/32 ID x 3/4" OD x 0.050 THK 18-8 SST
E 8 025-030 Washer, Lock, Split, 5/16", Blk Ox.
F 8 021-050 Screw, 5/16"-18 x 1" BH, Pin in Torx T-40, Black Oxide, Loctite
G 12 021-002 Screw, Machine 5/16"-18 X 1-1/4" L, FH, Pin in Torx® T40, Black Oxide, Thd. Lk.
H 3 024-003
Anchor, Secure Bolt, 3/8" x 2-1/2" L, 5/16"-18 Thread, BH, Pin in Torx® T45, SST
Post
J 2 024-001 Anchor, Concrete, Wedge, 3/8"-16 X 3.5", Zinc
K 2 026-008 Nut/Washer Assy. 3/8"-16, Zinc, Thd. Lk.
L 3 025-009 Washer, Flat, 3/8"
Rev. A - 3/14/18
091-914
Page 1 of 2
www.norix.com ● TEL [phone]
Assembly Notes:
Norix is not responsible for any damage due to improper installation. If your shipment does not match the parts list, please contact Norix Customer Service at 800-234-4900.
Norix reserves the right to modify design specifications at any time without an obligation to owners of previously sold products.
___________________________________________________________________________________________________________________________________________________________________________________________________
Oasis Classroom Table
Bolt Down
Assembly Instructions
For Model Number
O23072-XXXXXXX-XXXX-XXXB

Mark Floor
Locations
K
J
L
H
L
Step 3:
Position unit at final location and mark anchor
locations through holes on Legs. Remove Table
and drill holes. Completely remove all concrete
dust.
Step 4:
For Frame: Place Flange Nuts(K) on Anchor Wedges(J) and drive
Anchors into holes using a rubber mallet. Remove Flange Nut after
setting Anchor. With Anchor Wedges installed put Frame
Weldment(A) over Floor Anchors(J) and secure with Flange Nuts. Use
socket extention and magnetic socket to tighten.
For Three Single Legs(C)use Secure Bolt Anchors(H) and 3/8 Flat
Washers(L).
Step 3:
Position unit at final location and mark
anchor locations through holes on Legs.
Remove Table and drill holes. Completely
remove all concrete dust. Place Flange
Nut on Anchor and drive Anchors into
holes using a rubber mallet. Remove
Flange Nut after setting Anchor.
Rev. A - 3/14/18
091-914
Page 2 of 2