norix Protege II Single PROT100 Series User manual

Rev. C - 4/3/14
091-824
Note: Do not tighten screws until assembly is complete.
PARTS LIST
ITEM
NO.
QTY REV PART NUMBER DESCRIPTION
A 1 A 037-PT001-XX Protege II Deck
B 2 A 036-PT001-XX Protege II Endframe
C 8 A 027-PT001-XX Protege II Tube Cap
D 4 A 025-043 Washer, Flat, 3/8" ID x 11/16" OD, Black Oxide
E 12 A 025-041 Washer, Flat, 1/4" ID x 5/8 OD, Black Oxide
F 12 A 021-133
Screw, Machine, 1/4-20 X .625", CH, 4mm Hex
Socket, Black Oxide
G 4 A 030-PT001-XX Protege II Floor Bracket
H 4 A 021-135 Screw, Lag, M8X45, Hex Head, Black Oxide
I 4 A 025-044 Nut, Lock, 1/4-20, Black Oxide
J 4 A 024-023 Concrete Anchor 1/2" x 1-3/4" for 5/16" Lag Bolt
Page 1 of 3
www.norix.com ● TEL [phone]
Assembly Notes:
Norix is not responsible for any damage due to improper installation. If your shipment does not match the parts list, please contact Norix Customer Service at 800-234-4900.
Norix reserves the right to modify design specifications at any time without an obligation to owners of previously sold products.
___________________________________________________________________________________________________________________________________________________________________________________________________
Protege II Single
Assembly Instructions
Model Number
PROT100-XX

037-PT001-XX (1 PCS)
A
036-PT001-XX (2 PCS)
B
C
G
F
E
D
I
H
J
K
L
027-PT001-XX (8 PCS) 030-PT001-XX (4 PCS)
021-133 (12 Pcs)
025-041 (12 Pcs)
025-043 (4 Pcs)
025-044 (4 Pcs)
021-135 (4 Pcs)
024-023 (4 Pcs)
071-016 (1 Pcs)
071-018 (1 Pcs)
Rev. C - 4/3/14
091-824
Page 2 of 3

Rev. C - 4/3/14
091-824
B
A
E F
Step 2: Determine if Freestanding, Bolt Down, or Bunked.
A: If Free Standing Insert (8) Tube Caps (C) in the top and bottom of the End
Frames.
B: IF Bolting to Floor use (4) Floor Brackets (G), (4) 1/4" x 5/8" Screws (F), (4) 1/4"
Washers (E), and (4) Lock Nuts (I) and secure to each End Frame Leg using 4mm
Allen Wrench (K) and 11.3mm Wrench (L). Insert (4) Tube Caps (C) into bottom of
End Frame Legs Aligning cut-out with Lock Nut. Bolt to Floor Using (4) Concrete
Anchors (J), (4) 3/8" Washers (D) and (4) Lag Screws (H). Insert (4) Tube Caps (C) in
the tops of End Frame Tubes.
C: If Bunked, See Instructions for PROT200-XX
C
C
I
J
F
E
H
D
G
Step 1: Using (4) 1/4" x 5/8" Screws (F) and (4) 1/4" Washers (E) Secure Deck (A)
to End Frame (B) Using 4mm Allen Wrench (K). Repeat for other end Frame.
Page 3 of 3