norix PRD240 User manual

Drill Guide, Pin (1)
011-063
5/8" Drill Bit (1)
029-944
Shim (4)
060-197
Screw, 5/16-18 X 5/8" L, BH (2)
021-118
Ball Lock Pin (2)
002-027
Guide Tube (2)
029-941
Pin Extractor Tool (1)
011-066
Concrete Anchor,
5/16" X 2" L (4)
024-024
Floor Anchor Bracket (2)
011-058
Anchor Hook, Left (1)
011-067
Anchor Hook, Right (1)
011-068
Anchor Tab, Straight (2)
011-059
Important Note: For a successful installation, careful and accurate
layout of the anchor brackets is a must. Read through the
instructions first and familiarize yourself with all of the steps. If you
have any questions, please call Norix Customer Care before
proceeding. Norix is not responsible for damage to components
due to improper installation.
Security Caulk is highly recommended to help seal gaps and
secure the furniture in place. Apply caulk to clean surfaces.
Anchor hardware:
Please familiarize yourself with the anchoring components as shown below.
If any components are missing, contact Norix Customer Care before proceeding.
Patents Pending
Tools Needed
Low RPM Variable Speed Drill
Hammer Drill
5/16" masonry drill bit
Pin-in-Torx® Driver Bit T-40 (provided)
5/8" Drill Bit (provided)
Rev. B - 10/30/20
091-993
Page 1 of 9
www.norix.com ● TEL [phone]
Assembly Notes:
Norix is not responsible for any damage due to improper installation. If your shipment does not match the parts list, please contact Norix Customer Service at 800-234-4900.
Norix reserves the right to modify design specifications at any time without an obligation to owners of previously sold products.
___________________________________________________________________________________________________________________________________________________________________________________________________
Prodigy Nightstand
Assembly Instructions
Model Number
PRD240

Molded line
on Nightstand
First line to draw
Second line to draw
Connect the two "T"s
using a chalk line
or straight edge
Mid-wall installation:
Note: In a mid-wall installation, the Left and Right
Anchor Hooks will not be used.
Both Ball Lock Pins and Guide Tubes will be used.
1. Marking the Location
Place the Nightstand on the floor in an upright position
in the location where it is to be installed.
2. Mark a line on the floor along the sides of the
Nightstand, toward the center.
3. Locate the molded line at the center of each side,
and mark the floor at this location, perpendicular to the
first line. When finished marking, you will have what
looks like a letter "T" on each side.
4. Move the Nightstand aside.
5. Using a straight edge or chalk line, mark a line down
the center, by connecting the bases of the two "T"s that
were drawn in step 3.
Nightstand
open areas
The procedure for a corner installation is different from a
mid-wall installation . These will be shown separately. See
page 6 for corner Installation.
Page 2 of 9
Rev. B - 10/30/20
091-993

3"
Centerline
Align vertical face
with inward line
Mark (4) drill locations
for Concrete Wedge Anchors
M
Drill Guide
Molded line is
centered in hole
6. Carefully measure 3" inward from the first line
and mark a second line. Repeat on the other side.
7. Place Floor Anchor Bracket with holes centered on
centerline as shown, and vertical face aligned with
the line as shown.
Mark (2) holes on floor for Concrete Wedge Anchors.
Repeat on the other side. When (4) drilling locations
have been marked on the floor, set Brackets aside.
8. Install Floor Anchors and Brackets
If floor anchors other than the provided Concrete
Wedge Anchors are to be used, consult the
manufacturer for proper installation.
If the provided Concrete Wedge Anchors are to be
used, drill (4) 5/16" dia. holes a minimum of 1" deep
into the floor at the locations where previously
marked.
Vacuum debris from the holes.
Place the (2) Brackets back into their locations as
shown and install the Concrete Wedge Anchors,
securing the Hex Nuts tightly to the Brackets. Ensure
that the brackets are still aligned with the centerline
and the vertical face is still aligned with the 3" mark.
Make adjustments if necessary. It is critical that these
brackets are installed inline and in the correct
position. The provided Shims can be used to help
level the brackets.
9. Drill Holes and Install Brackets Onto Nightstand
To drill the holes and install brackets, it is easiest if the
Nightstand is inverted. Place padding on the floor to
protect the Nightstand from scratches.
Wear protective gloves when drilling holes, in case of
an accidental slip.
Place the Drill Guide on the Nightstand so that the
molded line is centered in the diamond shaped hole
in the Drill Guide as shown. The Drill Guide may be
held by hand, or clamped in place with a padded C-
clamp if necessary.
It is important to drill the holes accurately in the
correct position, centered and in line with the molded
line.
Using the provided 5/8" brad-point drill bit, drill through
the Nightstand. Drill carefully, and don't force the bit.
The Guide will help drill a hole that is perpendicular to
the outer face of the Nightstand.
Repeat drilling a hole on the other side.
3"
3"
Make new lines
3'' inward
Page 3 of 9
Rev. B - 10/30/20
091-993

N
Guide Tube
J
Straight Anchor Tab
5/16" X 5/8" L Screw
10. Install Anchor Tabs on the Nightstand
Install (2) Straight Anchor Tabs where shown, using
(2) 5/16" Screws.
11. Install Guide Tube
Insert the Guide Tubes into the drilled hole on
each side.
Page 4 of 9
Rev. B - 10/30/20
091-993

Pin Extractor Tool
Ball Lock Pin
E
F
Ball Lock Pin Installed
Outer surface of Nightstand
BB
WALL
Floor Bracket
Anchor Tab
KK
WALL
Tab engaged
under Floor Bracket
12. Set Nightstand in Place
Turn the Nightstand upright
and position in place over the
Floor Brackets.
Slide the Nightstand to
engage the Anchor Tabs with
the Floor Brackets.
13. Install the Ball Lock Pins
Thread the Pin Extractor Tool into
one of the Pins until it is almost all
the way in. This will retract the two
ball bearings at the end of the pin.
Insert the Pin into the Guide Tube
at one end until the Head of the
Pin is below the outer surface of
the Nightstand.
Unscrew the Tool from the Pin.
The Pin is now locked in place.
Repeat for the 2nd Lock Pin.
Installation is complete.
Page 5 of 9
Rev. B - 10/30/20
091-993

Second line to draw
First line to draw
Molded line
on Nightstand
Corner Installation:
1. Marking the Location
Place the Nightstand on the floor in an upright position
in the corner location where it is to be installed.
2. Mark a line on the floor along the exposed side of
the Nightstand, toward the center.
3. Locate the molded line at the center of the
exposed side, and mark the floor at this location,
perpendicular to the first line. When finished marking,
you will have what looks like a letter "T" on the floor.
4. Move the Nightstand aside.
5. Measure the width (from front to back) of the
Nightstand on the side that goes in the corner. Divide
this number in half. Measure out from the corner, and
make a mark on the floor at this dimension.
6. Using a straight edge or chalk line, mark a line down
the center, by connecting the base of the "T" and the
line previously drawn.
Half the width
(front to back)
of Nightstand
Connect the "T"
and the line from
Step 5 using a
chalk line or
straight edge.
Page 6 of 9
Rev. B - 10/30/20
091-993

3"
Align vertical face
with inward line
Centerline
Brackets Touching
3"
7. On the side that will be exposed, carefully
measure 3" inward from the first line
and mark a second line.
Exposed end: 3"
8. Place the Floor Anchor Bracket so that the
holes are centered on the centerline as
shown, and the vertical face is aligned with
the inward line as shown.
9. Place the corner end Floor Anchor Bracket
so that it is in the same direction as the first
bracket, with the holes centered on the
centerline as shown. This bracket should be
touching the first bracket as shown.
Mark the (4) drill locations for the anchors.
Page 7 of 9
Rev. B - 10/30/20
091-993

Wall side uses Hook Tab
Hook faces
closest wall
Exposed side uses Straight Tab
10. Install Floor Anchors and Brackets
If floor anchors other than the provided Concrete
Wedge Anchors are to be used, consult the
manufacturer for proper installation.
If the provided Concrete Wedge Anchors are to
be used, drill (4) 5/16" dia. holes a minimum of 1"
deep into the floor at the locations where
previously marked.
Vacuum debris from the holes.
Place the (2) Brackets back into their locations as
shown and install the Concrete Wedge Anchors,
securing the Hex Nuts tightly to the Brackets.
Ensure that the brackets are still aligned with the
centerline and the vertical face is still aligned with
the 3" mark. Make adjustments if necessary. It is
critical that these brackets are installed inline and
in the correct position. The provided Shims can
be used to help level the brackets.
11. Drill Holes and Install Brackets Onto
Nightstand
Refer to page 3 and the section on Drill Holes
and Install Brackets Onto Nightstand.
Using the Drill Guide, drill a hole in only the
exposed side of the Nightstand. Do not drill a
hole in the side that goes against the wall.
12. Install Anchor Tabs on Nightstand
In a corner installation , the wall side of the
Nightstand will receive a Hook Anchor,
and the exposed side will receive a
Straight Anchor Tab. Use whichever hook
that will point to the closest wall. For
further clarification, see the illustration on
page 9, step 14.
Install the brackets using (2) 5/16" Screws.
Page 8 of 9
Rev. B - 10/30/20
091-993

N
Guide Tube
AA
Push Nightstand at an
angle to engage the
Hook first
Rotate the Nightstand to
engage the Straight Tab
RR
14. Set Nightstand in Place
Place the upright Nightstand over the
brackets and slide the Nightstand in
place at an angle, ensuring that the
Hook Tab engages the Floor Anchor
Bracket first. Once the back corner of
the unit touches the wall, the
Nightstand can be rotated into place,
engaging the Straight Tab with the
2nd Floor Anchor Bracket.
13. Install Guide Tube
Insert the Guide Tube into the drilled hole in the
side.
15. Install the Ball Lock Pin
Refer to Page 5, Step 13, to install the
Ball Lock Pin into the Guide Tube to
secure the Nightstand in place.
Page 9 of 9
Rev. B - 10/30/20
091-993