Nortel M7100N User manual

© 2000 Nortel Networks
P0908517 Issue 02
Enterprise Edge
M7100N
User Card

Page 1 Enterprise Edge M7100N User Card
Your Enterprise Edge M7100N telephone
Using Button
Inquiry Check what is programmed on your memory button. 1. Release all calls or lines with dial tone.
2. Press ƒ•‚.
3. Press the button that you want to check.
4. Read the display.
5. Press ƒwhen finished.
Adjusting the
display contrast 1. Press ƒ•‡.
2. Press⁄to·forthelevelyouwant;thehigherthenumberthehigher
the level.
Selecting a ring
type and volume
level
1. Press ĥfl.
2. Press ⁄, ¤, ‹or ›to hear the different ring types.
3. While the telephone is ringing, press √to adjust the
volume level.
4. Press ƒto store the ring.
Adjusting the
handset or
telephone
speaker volume
1. Press √when using the handset or the speaker.
Display
shows the time, date, and call information; guides you while
using features; tilts for easy viewing
Feature button
starts or ends a feature
Dial pad
Volume control
Memory button
is programmable to store a
feature or to automatically
dial an internal or external
number.
Hold button
Release button
cancels active calls

Page 2 Enterprise Edge M7100N User Card
Making and answering calls
Answering calls 1. When your telephone rings, lift your handset.
You are immediately connected to the call.
Making external
calls Depending upon the dialling mode programmed for your telephone, you may be able to dial your call before lifting your handset.
1. Pick up the handset.
2. Dial ‚(your system’s exchange line access code or a line pool
access code).
3. Dial the external telephone number.
Making internal
calls 1. Pick up the handset.
2. Dial the internal number.
Note: Extension numbers and the exchange line access code are
supplied by your System Administrator.
Making or
answering a
second call
The M7100N telephone allows you to have two calls active at the same
time.
You can switch between calls using ˙.
To answer a second call while on another call
1. Press ˙to put the first call on hold.
The second call automatically comes onto the line.
To hold a call and make a second call
1. Press ˙to put the first call on hold.
2. Dial the telephone number for the second call.
To return to the first call
1. Press ˙again to return to the first call on hold.
The second call is automatically put on hold.
˙To hold a call
1. Press ˙.
2. Press ˙again to return to the call on hold.
Check the display for confirmation or additional information.
Note: If you have difficulty selecting a line on your M7100N telephone,
ask your System Administrator to check your telephone's
programming. Your telephone must be assigned to use an
exchange line or line pool.
9

Page 3 Enterprise Edge M7100N User Card
Programming the memory button
Remember: Press ƒ•‚ to check a memory or line button.
Programming the
memory button External Autodial 1. If you are on a call or a line with dial tone, press ˙or®.
2. Press ƒ•⁄.
3. Dial the external number.
4. Press ˙to store the number.
5. Label your new button.
Internal Autodial
1. If you are on a call or a line with dial tone, press ˙or®.
2. Press ƒ•¤.
3. Dial the extension number.
4. Label your new button.
Features
1. If you are on a call or a line with dial tone, press ˙or ®.
2. Press ƒ•‹.
3. Press ƒand the feature code.
4. Label your new button.
Erasing the memory button
1. If you are on a call or a line with dial tone, press ˙or®.
2. Press ƒ•⁄.
3. Press ˙to erase the button.
Notice These telephones now conform to the latest standards in relation to the
positioning of Q and Z on the number buttons. The Q appears on button
number 7 and the Z appears on button number 9.
About the
memory button The memory button can store a telephone number or feature
code to give you one touch
dialling or feature activation. You
can change the memory button
by programming it with a new
number or feature code.
Memory button
Page 3 Enterprise Edge M7100N User Card

Page 4 Enterprise Edge M7100N User Card
Setting up the telephone
Connecting the cords ATTENTION Before attempting to carry
out any work on the telephone, ensure
that the line cord is unplugged from the
wall socket.
To remove any of the cords, squeeze
the release latch on the plug and gently
pull the plug from the socket.
Connect the handset cord to the jack
labelled with the telephone icon and
route the cord as shown.
Route the line cord through the stand
and connect the cord to the telephone
jack that is marked with the jack icon.
Attach the stand using either pair of
slots; to raise the back of the telephone
to its highest position, use these slots.
Once the above work is complete, plug
the line cord back into its wall socket.
Press here to
remove the stand.
1
Press here firmly
until it clicks, to
attach the stand.
2

Page 5 Enterprise Edge M7100N User Card
Setting up the telephone
Mounting the
telephone on
the wall
12 cm
Page 5 Enterprise Edge M7100N User Card P0908517 Issue02