Novy 830 User manual

IMPORTANT! PLEASE READ INSTALLATION INSTRUCTIONS AND TIPS ON REVERSE BEFORE PROCEEDING .








4 X
2 X
2 X
6 X
8 X
Dimensions of opening to cut out:
830  opening 845mm x 485mm
840  opening 45mm x 485mm
Make sure that an electrical socket is within
reach of the built in unit to plug into.
Carefully remove the hood
out of the packaging.
The direction of the
exhaust can be altered.
For alteration proceed as
follows:
emove the filter and
unscrew the 8 screws
of the motor.
Turn the motor
in the
desired
position and
reattach using
the same screws.
To obtain an upward
exhaust remove the 8
screws of the motor,
give the motor a quart
turn an reattach.
The clips are suited for plates with
a thickness of 18 mm - 35 mm.
Always install the hood with the control panel
to the right side of the user. This insures that
the plate opens properly and access to the
filter is not impaired.
Connect the exhaust pipe to the motor. Use a
ringclamp (adapt the length of exhaust pipe so
it can be reattached in case of dismantling).
Put the plug in the socket. Push the unit
upward into the opening until you hear a click.
The unit will now hang from the ceiling.
Tighten the clips (see) in position
(Beware! Do not screw excessively tight in
plasterboard). The unit is now ready for use.
When removing the unit, unscrew clips
completely. Always protect underlying
surfaces with blanket or cardboard when
installing or removing.
Separate the motor from the unit by removing
the 8 screws (see ), use the same screws to
attach the ductadapter to the unit.
Attach the other ductadapter to the bottom of
the motor with the screws provided.
emove the screws on the side of the
motor by which you intend to attach it
to the wall. Attach the bracket to the
motor with the same screws. Hang
the motor in place using the screws
provided (6 woodscrews or 4
stonescrews with plug)
Do not hang the motor from the
ceiling if possible!
Connect the ducts to
the motor (in and
out) with clamps and
aluminium tape.
Make the electrical
connection.
The ducts can be
installed at a 90°
angle or in a straight
line (see for
adaptation)
stone – concrete
wood
INSTALLATION INSTRUCTIONS FOR BUILT IN HOOD TYPE 830 & 840

INSTRUCTIONS IN CASE OF DISSOCIATED MOTOR
2 X
2 X
X X

BUILT IN HOOD STAINLESS STEEL
830 90 cm
840 120 cm
INSTALLATION MANUAL
DIMENSIONS
830
840
NOVY nv
Noordlaan 6
B - 8520 KUU NE
Belgium
Tel. [phone]
Fax [phone]
E-mail : [email protected]
www.novy.be
NOVY nv reserves the right to modify construction and prices at any time and without
reservation.
INSTALLATION
This hood is equipped with a powerful turbine (1080m³/h), Novy
peripheral extraction and Novy silencer. The motor has one exhaust Ø
150 mm. The exhaust can be adapted for an extraction to the left,
right, front, back or upward.
This hood is for domestic use only.
Installation height: min. 65 cm above gas, min. 60 cm above electric,
min. 75 cm above induction. Maximum height: 130 cm above cooking
surface.
Beware!
• The unit has sharp edges. Please wear protective gloves.
• Protect the underlying surface with cardboard or blanket when
installing (or removing) the unit.
Do’s and don’t’s
The exhaust system needs to be installed correctly!
• Never use a duct or chimney that is used for other purposes to
create an outlet for the hood
• Never diminish the diameter of the exhaust pipe. It will diminish the
suction power and increase noise levels.
• Use smooth uninflammable ducts
• Use Novy wall exit 906.178
• oof exits should allow enough air through
• Use aluminium tape 906.292 to ensure air tightness of connections
• Angles in ducts should be smooth not sharp
ELECTRICS
For connecting into the main the unit has a cord with plug and
grounding. Always plug into a grounded socket. The socket must have
easy acces. eplacement of the cord can only be done by a certified
electrician.
All relevant information can be found on the type plate (behind the
filter).
Electrical scheme
Damage due to faulty installation suppresses factory warranty.
Installation of a Novy hood without a Novy motor or the reverse
suppresses factory warranty.
Do not install a damaged unit. Contact Novy or your Novy
dealer.
juli ’08