NSA Antique DF-1214-BRZ User manual

Cleaning & Care
♦Unplug the appliance before cleaning.
♦Do not use any water or chemical-based solutions for cleaning metal surfaces.
♦Slightly moisten a cloth and then wipe off the surfaces of the fan.
♦In order to remove the dust from the protective fan grille use a vacuum cleaner or reverse
the assembly instructions ~ undo safety screw, open securing clips on grille edge and
wipe fan blades with a damp cloth.
♦Ensure fan is completely dry and the fan grille securely refitted before storage or
reconnecting to electrical supply.
♦ever immerse the fan or fan motor in water or other liquid.
♦If the fan is not used for long periods, protect with a suitable cover after cleaning, then
store in a dry place.
This appliance complies with both the low voltage and electromagnetic compatibility
directives. Its construction complies with current safety standards. We reserve the right to
make technical changes without prior notice.
Disposal
The packaging of your new fan has a recycle mark on it. Please
dispose of it as recycled paper or by using the “Dual System”.
The symbol on the product or on its packaging indicates that this product may not
be treated as general household waste. Instead it should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed information about the recycling of this
product, please contact your local council office, your household waste disposal service, the
store where you purchased the product or visit www.recycle-more.co.uk.
UK guarantee
12 months warranty valid only in respect of defects found to be due to faulty workmanship or
material. Proof of purchase is required to validate the guarantee. This guarantee is no longer
valid if the damage has been caused by a fall, alteration or repair by any unauthorised
persons or if the product has been resold.
This guarantee in no way affects your statutory rights.
Technical Data
Model o: DF-1214-BRZ (12” / 30cm)
Power: 45W
Voltage: 220-240V ~ 50Hz
Ref: IM/DF1214-BRZ/1903/GU86AA
Product Dims: 350 x390 x 460 mm (L*W*H)
W: 2.9kg
GW: 3.8kg
Class II Product
Tabletop Fan
12” / 30 cm
Mo el DF-1214-BRZ
Instruction manual
3 speeds
4 metal blades
Rotary controls
Oscillation
Tilt
Carry handle
Round base
Please keep safe for future reference
Please Recycle
4
© 2019 ewton Stovold Assocs Ltd
GU8 6AA / www.nsauk.com

Tabletop fan
Thank you for purchasing this tabletop fan. Please read the instructions and warnings
carefully before use to ensure safe & satisfactory operation of this product. Please retain this
information for future reference.
CAUTION:
Use the fan only as described in this manual. Misuse may cause a fire or an
electric shock
1. Do not operate the fan with a damaged
power cord or plug, after it malfunctions,
has been dropped or damaged in any
way. If the power cord is damaged it
must be replaced by a qualified service
engineer to avoid a hazard.
2. Close supervision is necessary when this
fan is used near children and pets.
3. Always turn off the fan after use, before
cleaning or moving location.
4. Do not insert fingers or other objects into
the fan guard.
5. Do not operate the fan in areas where
petrol, paint or other flammable liquids
are used or stored.
6. Do not place the fan near an open
flame, cooking or heating appliance or
hot surface.
7. This fan is not intended for use in wet or
damp locations. ever position the fan in
an area where it may fall into a bath or
other water container.
8. This fan should not be operated outside.
9. Always use on a dry, level surface.
10. Do not let the power cord hang over
the edge of a table or counter.
11. Arrange the power cord away from an
area where it may be tripped over.
12. ever place the power cord under a
carpet or rug.
13. To disconnect from the power supply,
grip the plug and pull from the power
socket. ever pull by the cord.
14. Do not hang or mount the fan on a wall
or ceiling.
15. This product is designed for household
and light commercial use O LY.
16. This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they
have been given supervision or
instruction concerning use of the
appliance in a safe way and
understand the hazards involved.
Operation
1. Position your fan on a dry, level surface & plug into an electrical socket.
2. To switch on the fan, turn the rotary speed control switch (9) to position 1, 2, or 3 position
(Hi * Med * Lo) as desired.
3. To assist the flow of air around the room push down the oscillation knob (8) located on
the top of the motor housing (10).
4. To stop oscillation, pull up the oscillation knob (8).
5. Airflow can be adjusted upwards or downwards by simply tilting the fan head to the
desired level. DO OT tilt fan head when the fan is on; this may damage the
mechanism.
Appliance components
Assembly
1. Loosen the pillar nut (16) & base washer (15) from main pillar (12); insert the main pillar
(12) through the upper ring (13) and into the hole in the fan base (14); then place base
washer (15) over the main pillar and secure in place with the pillar nut (16).
2. Remove the rear grill securing nut (5) from the motor cover and secure the rear grille (6)
to the motor cover using the three pins to align it keeping the carry handle at the top.
Then fasten grille securely in place with rear grille securing nut (6).
3. Push the fan blade (4) onto the motor shaft (7) until the fan blade is fully seated. For
models with shaft pins, push the fan blade onto the motor shaft by matching the slots
on the rear of the blade with the shaft pin.
4. Secure the fan blade (4) with the locking cap (3). The locking cap must be tightened
by turning it counter clockwise. Check that the fan blade rotates freely by turning it
with your hand. If it does not – check the rear grille (6) is correctly aligned on the motor
housing, the rear grille nut (5) is fitted correctly and the locking cap (3) is correctly
threaded & securely tightened.
5. Open the securing clips around the front grille and loosen the safety screw and nut (2)
at the bottom of the front grille (1). Position the front grille hook on the uppermost part
of the rear grille. Push the hook down firmly and press the rim of the front grille onto the
rear grille. Close all clips around the grille & tighten the safety screw.
1. Front grille
2. Safety screw & nut
3. Locking cap
4. Fan blade
5. Rear grille securing nut
6. Rear grille
7. Motor shaft
8. Oscillation knob
9. Speed control switch
10. Motor housing
11. Power cord & plug
12. Main pillar
13. Upper ring
14. Base
15. Base washer
16. Pillar nut
2
3