NSK Ti205L User manual

Caution
Airmotor Motor Cord NutMotor Nut
Motor Cord
Spanner
Handpiece Airmotor
Motor Insert
Fig.2
• Place the most priority of the patient's safety.
• For professional use only. Do not make wrong use of the handpiece.
• Do not disassemble, nor alter the handpiece.
• Check the vibration, noise and overheating outside the patient's oral cavity
before use. If any abnormalities are found, stop using immediately and con-
tact your dealer.
• If any abnormalities are found in use, stop using immediately and contact
your dealer.
• Do not drop, hit, or subject to excessive shock.
• Remove the airmotor after the air supply is stopped completely.
• Keep clean and dry supply air. Moisture and debris in supply air may cause
the airmotor to malfunction.
• Do not wash, soak, or wipe off the handpiece with/in the oxidation potential
solution (strong acid, superacid solution) or sterilized solution.
1. Features
• Various E-type (ISO-3964 Compatible) internal coolant attachments are
adaptable.
• Specially-coated cylinder provides outstanding durability.
• Selection of forward or reverse rotation, or stop is achieved at the airmotor.
• The NON-RETRACTION VALVE, incorporated in the rear joint, prevents suction of
oral fluids in a patient's mouth into the water line of the handpiece at the spray
water outlet port. (PAT. )
• It is repeatedly autoclavable up to 135˚C.
3. Connection / Disconnecting the Motor Cord
aConnection
Align the pipe of the airmotor and the pipe hole of the motor cord, and push the
airmotor onto the motor cord. Fasten the motor cord nut securely, holding the
motor nut by spanner.
sDisconnecting
To disconnect the airmotor from the motor cord, unscrew and detach the motor
cord nut, and gently pull out the airmotor, holding the motor nut by spanner.
2. Specifications
The EU directive 93/42/EEC was applied in the design and production of this medical device.
Thank you for purchasing the Ti205L Airmotor.
Please read this Operation Manual carefully and file for future reference.
Internal Coolant Airmotor
Ti205L
OPERATION MANUAL OM-M0071E
Caution
Ensure that the air supply has completely stopped before handling the
airmotor.
Caution
Ensure that the air supply has completely stopped before handling the
airmotor.
4. Connection / Disconnecting the Handpiece
aConnection
Insert the E-type handpiece in the motor insert, and turn until it clicks and
positioning mark are aligned.
sDisconnecting
Simply pull out the handpiece from the airmotor.
*Speed may slightly vary depending on the back-end configuration and type of hose used.
Model
Rotation Speed
Drive Air Pressure
Air Consumption
Lighting
Weight
Ti205L
18,000-22,000min-1(rpm)*
0.25MPa(2.5kgf/cm2)
48-55 L/min
Ye s
114g
Fig. 1
: AUTOCLAVABLE

Fig. 3 Fig. 4 Fig. 5
Fig. 7
Drive Air Tube
6. Replacing Bulb
qLoosen Motor Housing and detach from the motor, and remove the old light bulb
using the small pin, like the screw driver. (Fig. 6)
wAlign and insert the connector of the new bulb into the socket hole securely.
Screw the motor housing securely to the motor.
※Optional Bulb : TM Bulb (Pack of 3) Order No.Y900-078
7. Lubrication
Supply PANA SPRAY Plus or lubrication oil after each use and/or before autoclaving.
Lubrication Oil :
Supply 2-3 drops of the lubrication oil into the drive air tube. Run the airmotor for
a while, approx. 10 seconds, to deliver the oil into the airmotor.
PANA SPRAY Plus :
qMount the arrow-head spray nozzle tip into the spray port.
wInsert the arrow-head spray nozzle in the drive air tube of the handpiece and
spray for approximately 2-3 seconds.
8. Sterilization
The Ti205L airmotor is Autoclavable.
Autoclave sterilization required after each patient as noted below.
■Autoclaving Procedure
qWipe off dirt with alcohol-soaked cloth.
wLubricate the motor. Use PANA SPRAY Plus or Lubrication Oil. When
Lubrication Oil is used, be sure to operate the motor for a few seconds before
autoclaving.
eInsert in a sterilizing pouch and seal.
rAutoclavable up to a max. 135˚C.
ex.) Autoclave for 20 min. at 121˚C, or 15 min. at 132˚C.
Caution
•Supply lubricant until it comes out of the exhaust pipe (for approx. 2
seconds).
•Hold the PANA SPRAY Plus can upright.
Caution
Do not touch the glass section of new bulb.
Caution
•In case the sterilizer chamber temperature could exceed 135˚C during
the dry cycle, skip the dry cycle.
•Always place the airmotor in the center or upper shelf of the chamber,
as the local temperature at the bottom of chamber could rise beyond
the set value.
•Do not wash, soak, or wipe off the handpiece with/in the oxidation po-
tential solution (strong acid, superacid solution) or sterilized solution.
5. Forward/Reverse Rotation
aForward Rotation : Turn the FWD/REV change ring to “F”as shown in Fig. 3.
sReverse Rotation : Turn the FWD/REV change ring to “R”as shown in Fig. 4.
dWhen the FWD/REV change ring is positioned at the middle of “F”and “R”, the
drive air is interrupted and the motor does not rotate. (Fig. 5)
Fig. 6
Fig. 8
PANA SPRAY Plus
Arrow-head
Spray Nozzle Tip
Airmotor
Cover Bulb
Socket Hole
Connector
View from A
Bulb
A