NUTRIBULLET Slow Juicer User manual

SLOW JUICER
User guide.

2
GENERAL SAFETY
INFORMATION
• This juicer system has moving
parts, and is not intended for
use by children or persons
with reduced physical,
sensory, or mental capabilities,
or who lack experience
and knowledge of its safe
operation. Such persons
require close supervision and
thorough instruction on its
proper use and safe operation.
• Close supervision is necessary
when any appliance is used
by or near children. Children
should be supervised to
ensure that they do not play
with the appliance. Keep cord
out of reach of children. This
appliance is not a toy.
• To protect against fire,
electrical shock and injury to
persons, do not immerse the
appliance, motor base, cord,
or plug in water or any
other liquid.
• Unplug from outlet when not
in use, before putting on or
taking o parts, and before
cleaning or attempting to
move the appliance.
• To unplug, grasp the plug and
pull from the outlet. Never pull
from the power cord.
Avoid contact with
moving parts.
• Regularly inspect the power
cord, plug, and entire
appliance for any damage.
• Do not operate any appliance
with a damaged cord or
plug or after the appliance
malfunctions, or is dropped or
damaged in any manner.
• Contact NutriBullet®customer
service for assistance at
1 [phone].
• The use of attachments not
recommended or sold by
NutriBullet®may cause fire,
electric shock, or injury.
Important safeguards.
Warning! To avoid the risk of serious injury, carefully read all instructions
before operating your NutriBullet® Slow Juicer. When using any electrical
appliance, basic safety precautions should always be observed, including
the following important information.
Save these instructions!
FOR HOUSEHOLD USE ONLY
!

3
• This appliance is for
household use only. Do
not use this appliance for
anything other than its
intended use.
Do not use outdoors.
Misuse may cause injury.
• Do not let the power cord
hang over the edge of a table
or countertop.
• Do not let the power cord
touch hot surfaces, including
stove, or become knotted
or tangled.
• Always make sure the juice
bowl cover is securely in place
and locked to the juice bowl
before the motor is turned
on. Do not attempt to unlock
the juice bowl cover from the
juice bowl while the juicer is in
operation.
• Always make sure the juicer
is turned o after each use.
Make sure the auger has
stopped rotating and the
motor has completely stopped
before disassembling. The
juicer will automatically turn
o if the juice bowl cover is
removed during operation.
• Do not push food into the
feed chute with your fingers
or utensils. Always use the
food pusher provided. Do not
place hand or fingers into the
feed chute when it is attached
to the appliance. If food
becomes lodged in the feed
chute, use the food pusher
provided to push it down. Turn
motor o and ensure that all
moving parts have stopped
before disassembling juicer to
remove the remaining food.
• Turn motor o, unplug unit,
and ensure that all moving
parts have stopped before
disassembling juicer to
remove the remaining food or
to clean.
• Do not use appliance if the
auger is damaged.
• This appliance has a
polarized plug (one prong
is wider than the other). To
reduce the risk of electric
shock, this plug will fit in a
polarized outlet only one way.
If the plug does not fit fully in
the outlet, reverse the plug.
If it still does not fit, contact a
qualified electrician. Do not
modify the plug in any way.
ADDITIONAL
SAFEGUARDS
• Remove and safely discard
any packaging material or
promotional labels before
using the juicer for the
first time.
• To eliminate a choking
hazard for young children,
remove and safely discard the
protective cover fitted to the
power plug of this appliance.
• Do not put any NON-food

4
items into the feed chute.
Always make sure the
juicer is properly and
completely assembled
before connecting to
a power outlet
and operating.
Ensure that the surface
where the appliance
operates is stable, level,
clean, and dry.
• Vibration may occur during
normal operation.
• Any significant spillage onto
the surface under or around
the appliance, or onto the
appliance itself, should be
cleaned and dried before
continuing to use
the appliance.
• When using this appliance,
provide adequate air space
above and on all sides
for circulation.
• Do not operate juicer for more
than 15 minutes at a time
when juicing at a rapid rate
or with firm pressure. Allow
the motor to rest for 1 (one)
minute between each use.
This juicer is only designed
to juice fresh fruits and
vegetables. Do not use any
frozen fruits or vegetables.
• Remove rind from all citrus
fruit before juicing.
• Do not juice stone fruit unless
pits or seed stone have
been removed.
Do not leave the appliance
unattended when in use.
Keep hands, fingers, hair,
clothing, as well as spatulas
and other utensils, away from
the feed chute opening during
operation.
Keep the appliance clean.
Refer to the Care and
Cleaning section for tips and
best practices.
Any maintenance other than
cleaning should be performed
by an authorized NutriBullet®
Service Center.
Do not attempt to repair or
service this juicer yourself.
Contact NutriBullet®Customer
Service for assistance at
1 [phone].
If any of the contained
instructions or warnings
are not understood, please
contact NutriBullet®Customer
Service for assistance at
1 [phone].
WARNING!
!

5

6

Contents.
Thank you for purchasing the NutrBullet® Slow Juicer.
08 What’s included
09 Assembly Guide
10 Before first use
11 Assembly
14 Usage instructions
17 Juicing tips
19 Troubleshooting
20 Disassembly
22 Care and maintenance
23 Replacement parts
23 How to store
24 NutriBullet®Slow Juicer one-year
limited warranty
27 Warranty registration

8
What’s included.
150 WATT MOTOR BASE JUICE BOWL JUICE BOWL COVER
JUICING SCREENSTEELTIPPED AUGER
CLEANING BRUSHPULP
CONTAINER
ROTATING BOWL
BRUSH
FOOD PUSHER24 OZ JUICE
CONTAINER

9
Assembly guide.
food pusher
grinding assembly
rotating bowl brush
juice bowl
with Juice Spout and spout
cover, and Pulp Spout
cleaning brush
power switch
pulp container juice
container
150 watt motor base
juice bowl cover
with Feed Chute
and Juice Bowl Lid
auger
juicing screen

10
Before first use.
Before using your juicer for the first time, please take a moment to
perform the steps below.
UNPACK
Open the box and remove the appliance with its various
components, placing all parts on a flat, level surface.
SEPARATE
A few parts will be packed together. Separate them using the
following 3 steps (see image):
a.Lifting up, remove Grinding Assembly and Rotating Bowl Brush together
from the Juice Bowl.
b.Detach Rotating Bowl Brush by moving it down.
c. Lifting up, remove the Auger from Juicing Screen.
CLEAN
Immerse all detachable parts and accessories (not the base) in
warm, soapy water. Rinse and dry.
Clean the outside of the base with a clean, damp cloth.
WARNING: Never submerge the Motor Base in water or any other liquid.
(a)
(b)
(a) (c)

11
Assembly.
1Before starting assembly,
check that the appliance
is unplugged and and the
power switch is off.
2Check the position of the
pulp plug. Look at the
bottom of the Juice Bowl.
Make sure the pulp plug is
positioned properly in the
pulp spout (see image).
4Put the Juice Screen into
the Rotating Bowl Brush.
3Attach Juice Bowl to Motor
Base. Position the Juice
Bowl on top of the Motor
Base and push downwards,
making sure the bowl is
tightly fastened to the base
and locked securely in
place. The Juice Bowl must
be attached in its proper
position or the appliance
will not operate.

12
6Put the Auger into the
strainer and ensure
the Auger is positioned
properly onto the center
axis. Turn and press down
on the head until it is
seated securely into place.
7Place the Juice Bowl Cover
on top of the Juice Bowl,
making sure the “unlocked”
symbol on the lid aligns with
the arrow symbol on the
bowl. Rotate cover clockwise
to lock it in place.
NOTE: To ensure the Juice Bowl
Cover is fully locked, rotate it until
the “locked” symbol on the Juice
Bowl Cover aligns with the up-
triangle symbol on the Juice Bowl
(see closeup image).
Make sure the Juice Bowl Cover
is fully locked in position, or the
appliance will not operate. (To
remove the Juice Bowl Cover
from the Juice Bowl, rotate it
counter-clockwise.)
5Place the screen and
brush assembly into the
Juice Bowl.
NOTE: You may need to turn it
slightly before it seats properly.

13
8Place Juice and Pulp
Containers under spouts.
8aPosition the Juice Container
below the juice spout, this is
on the right side of the Juice
Bowl with the spout cover.
8bPlace the Pulp Container
below the pulp spout.
NOTE: The juice and Pulp
Containers must be in their proper
positions before juicing. During
operation, juice will flow into the
Juice Container from the juice
spout, while pulp will be ejected
from the pulp spout and collected
by the Pulp Container.
9Put the Food Pusher into the
feed chute. The juicer is now
ready to operate.

14
Usage instructions.
1Prepare foods for juicing,
and make sure non-
juiceable foods are not used.
• Remove any hard seeds, pits,
and skin – for example, peel
and pits should be removed
from oranges, lemons,
grapefruits, and melons.
• Cut foods into smaller pieces
if needed to fit into the feed
chute.
• Do not attempt to process
thick or hard foods that
don’t contain any juice
to extract (for example,
it is not recommended to
process bananas, avocados,
coconuts, or similar hard
foods, since these may
damage the motor).
2Before plugging the power
cord into an outlet, make
sure the power switch is in
the “OFF” position.
3The power switch has three
settings. Pressing the power
switch to the “ON” position
activates the motor and
starts making juice; pressing
the power switch to “OFF”
turns o the machine;
and “REV” means reverse
rotation, only used when
something is stuck and you
need to unclog the unit.

15
4Make sure the juice and
Pulp Containers are in their
proper positions.
5Plug the juicer into the
power outlet, then press
the power switch to the
“ON” position.
6Drop the prepared fruits
or vegetables into the feed
chute and gently push
the items down into the
grinding assembly, using
the Food Pusher.
CAUTION: Never place your your
finger or hand into the
feed chute. Always use the food
pusher provided.
6aThe appliance will start to
process the food items. After
a few moments, the juice will
flow out.
NOTE: For ecient juicing,
alternate feeding soft foods and
hard foods into the feed chute.
For example, follow leafy greens
with an apple slice, or orange with
a carrot. The harder produce will
help with processing the softer
produce and extract more juice.
CAUTION: The auger must stop
rotating before changing from "ON"
to "REV". Do not turn the power switch
from "ON" to "REV" or from "REV" to "ON"
without pressing the power switch to
"OFF" first. Once the appliance is "OFF"
and has stopped running completely
then turn the power switch from "OFF"
to "REV" or from "OFF" to "ON".

16
7While you are juicing, you
may choose to open the
wide chute lid, which will
open the chute to 3-inches.
This will accommodate
larger pieces of fruits and
vegetables. When the wide
chute lid is in the open
position, the motor will
pause and the Auger will
stop rotating. After you
have inserted fruits and
vegetables into the large
chute, close the wide chute
lid to restart the motor and
continue juicing.
8Once the Juice Container
is full, or all food has been
processed, turn the power
switch to “OFF”. If you have
more food to process,
empty the Juice and Pulp
Containers before starting
a new round of juice
extracting.
NOTE:Do not insert too much
food to extract at one time. During
operation, once the Juice Container
is full, you must stop the appliance
and empty the Juice and Pulp
Containers before the next
juicing cycle.
CAUTION: During operation, if the
Juice Bowl Lid is disconnected from
the Juice Bowl, the motor will stop.

17
PROPER PRODUCE PREP
Prepare fruit and veggies
before inserting them into
the juicer:
• Clean produce properly.
Rinse with lukewarm water,
produce wash, or water and
apple cider vinegar.
• Peel or remove skin as
needed. Foods with thick or
hard skin must be peeled
before being put into
the juicer.
• Remove rind from all citrus
fruits before juicing.
• Remove large pits and seeds
from stone fruit before
juicing. Stone fruit may be
used only if the seeds or pits
have been removed. Fruit with
hard cores must be pitted. The
cores of peach, plum, mango,
and apricot should not be put
into the feed chute, to avoid
any potential malfunction.
• Chop food items down to the
right size - small enough to
fit easily into the feed chute,
without having to force pieces
down with the Food Pusher.
Juicing tips.
• Foods with less moisture and
hard fiber: Cut into slices.
• Leafy vegetables and foods
with long, hard fiber (such as
celery and kale): Cut the stems
into 4 inch pieces and then roll
up the leaves well.
• For ecient juicing, alternate
feeding soft foods and hard
foods into the feed chute.
For example, follow leafy
greens with an apple slice, or
an orange with a carrot. The
harder produce will help with
processing the softer produce
and extract more juice.
• Frozen food items can be
put in the juicer after being
defrosted.
FEED CHUTE
• Never place your hand,
fingers, utensils, or other
foreign objects into the feed
chute while it is attached to
the appliance.
• Do not overload the feed
chute. Insert food gradually,
at a pace the juicer can
keep up with.
• Use only the provided Food
Pusher to push food into

18
the feed chute. Never use
fingers, utensils, or any other
apparatus.
• Never use excessive force to
push items into the feed chute.
• After inserting food, ensure
all items have moved down
the feed chute before
adding more.
• If any food gets stuck in the
feed chute, use the Food
Pusher to move it down
the chute.
• For best taste, consume fresh
juice and pulp within 72 hours
of juicing.
CAUTION: Do not operate the unit
without feeding food into it, to avoid
damaging the grinding assembly.
FOODS THAT CANNOT
BE JUICED:
• Foods that do not contain
juice to extract (for example,
bananas, avocados, coconuts)
• Stone fruits that have large
pits or seeds that have not
been removed
• Hard fruits or thick vegetables
rich in fiber and starch
• Frozen fruits or vegetables

19
PROBLEM: PARTS
ARE DIFFICULT TO
DISASSEMBLE
Solution: After finishing juicing,
in order to detach and clean
parts more easily, continue
to run the juicer for about 30
seconds without adding any
additional food in order to
process any food that might
be stuck in the Auger and
Juicing Screen.
Another tip: after you are done
extracting juice, pouring some
water in the feed chute to clean
it can help make it easier to
disassemble.
PROBLEM:
JUICER IS STUCK
AND WON'T OPERATE
Solution: If the juicer is stuck
and not operable, press the
power switch to the “OFF”
position. Then press the
RESET switch, which is located
at the bottom of the base
(see image).
Next, press and hold the power
switch in the “REV” position
for few seconds, then try
operating again.
Troubleshooting.
If this reverse function
does not work, turn o
the machine, unplug, and
reassemble it, using the
instructions given earlier in this
guide. After reassembly, try
turning on the machine to see
if normal function has been
restored.
PROBLEM: THE JUICER
TURNED OFF IN THE
MIDDLE OF JUICING
If the motor overheats, the
juicer will turn o.
Solution: If the juicer is
overheated and stops working,
unplug it and allow it to cool
down for at least fifteen
minutes before attempting to
use again.

20
Disassembly.
1Make sure the juicer is
powered OFF, cooled
down completely, and
unplugged before starting
disassembly. Ensure that
the motor has completely
stopped, the grinding
assembly has stopped
moving, and all moving
parts have stopped before
disassembling juicer.
2Remove the Juice Container
from under the juice spout.
To prevent drips, use the
spout cover to close the
juice spout.
3Remove the Pulp Container
from under the pulp spout.
4Twist the Juice Bowl
lid counter-clockwise
to unlock it, then lift to
remove it from the top of
the juicing jar.