nuVita 1170 User manual

Digital bottle warmer
Instruction manual

22
Keep the instruction sheet for future reference:
Only use the appliance indoors. NEVER use it outdoors.
Ensure the voltage is compatible with the electricity supply.
Always add water rst before switching the appliance on.
Use the appliance away from children. Store the appliance in a safe place
away from children.
When nish using the warmer, make sure it is o and pull out plug
while storing it dry in a safe place afterwards. Empty the water from
the device. Keep it away from children’s reach. Note the surface of the
heating element is subject to residual heat after each use.
Do not immerse any xed or removable parts in water to avoid injury.
Follow the heating guidelines suggested for child’s safety during
feeding.
Do not use any appliance with a damaged part. If the damage is from a
new unit, return the unit immediately. The supplied accessories of the
bottle warmer should only be use.
•
•
•
•
•
•
•
•
important safety notes
Bottle Warmer Body
Ring
Bottle and Jar Basket
Sterilisation cover
Detachable power cable
Water Measuring Cup
A.
B.
C.
D.
E.
F.
box contents
ENGLISH
a
c
b
d
E
f

23
If you are experiencing problems with the Nuvita 1170 digital bottle
warmer immediately contact the establishment where the item was
purchased.
customer service
control panel
On / O Start / Timer Minus Menu Plus
Baby bottle
warming
Gentle defrost
Baby food
warming
Sterilisation and
Fast warming
Timer
indicator light
Light will turn on when device is on and/or a cycle is running.
Light will blink continuously when a cycle ends.
Light will blink for 2 seconds when water nishes and device will switch
o automatically.
•
•
•

24
The “beep” sound can be heard once the in the following:
Plugging in the device
Pressing any button
Once the program/cycle starts the beep can be heard twice
Once the program/cycle nishes the beep can be heard three times.
If the water nishes a long beep of 2 seconds will be heard.
•
•
•
•
•
beep sound
These instructions are to be used as a guide only in order to operate the
product. There are many variables and factors, such as size of the bottle,
ambient temperature, and starting temperature of the food which aects
the intended performance of this device. It may be necessary to adapt the
times indicated in the table. Always test the temperature of food before
feeding baby. The temperatures written in the chart below refer to the
starting temperature of the milk.
setting guide
CAUTION
Check temperature of liquid before feeding it to the baby.
8:00 70 70
food jar warming
heat
time
( min:sec )
heat
time
( min:sec )
recom-
mended
water
(ml)
recom-
mended
water
(ml)
8:00
20°c5°c
jar
content
home with
steriliser
cover
start
temperature

25
milk
gentle defrost
warming
jar
content
starting
tempera-
ture
ending
tempera-
ture
heat
time
(
min:sec)
heat
time
(
min:sec)
heat
time
(
min:sec)
-5°c
20°c
20°c
37°c
5°c
37°c
recom-
mended
water
(ml)
recom-
mended
water
(ml)
recom-
mended
water
(ml)
60ml
200
8:3040 150
6:00 150
180ml 19:0060 12:00 120ml 15:0050
200
9:00
200
250ml 25:0070 15:00 300ml 30:0080 20:00
90ml 12:0050 8:00
210ml 23:0060 13:30 150ml 17:0050 10:30 280ml 28:0070 17:30 330ml 35:0090 24:00
fast warming
heat
time
(
min:sec)
heat
time
(
min:sec)
20°c
37°c
5°c
37°c
recom-
mended
water
(ml)
recom-
mended
water
(ml)
3:00
20
1:15(*)
30
5:303:00 4:00
30
2:30
40
6:303:00 7:004:00 3:301:30 6:003:00 4:302:30 6:303:30 7:004:30
(*) 1:15 is the actual time needed, you may set the timer to 1:30

26
Please refer to the SETTING GUIDE section for table of volume and
warming times
1.
2.
3.
4.
5.
6.
operation
BABY BOTTLE WARMING
Insert the basket and if necessary the adapter ring.
Fill the tank with water as indicated. Do not overow.
Place the bottle without the teat and protective cap inside the bottle warmer.
Plug the device into a power outlet. Press the on/o button once to turn
the unit on. The display will show the bottle icon, digits 0:00 and indicator
light will switch on. “Baby Bottle Warming”will be the default function.
Digits will start blinking after 1 second to indicate the time can be set by
pressing the +/- buttons (30 sec for each press and 1 min with long press
up to 40 minutes).
(If there will be no actions chosen within 30 seconds the bottle warmer
will shut o automatically).
Once the time has been set, press the START button. When cycle ends,
device will beep 3 times before to shifts automatically to the keep
warming mode.
Switch o the device by pressing the on/o button if the keep warming
function is not needed.
Before using the bottle warmer, ensure the mains outlet is of correct
voltage.
The bottle warmer must be out of reach of children, placed on a stable
surface.
Plug the cable to a power outlet.
Before heating, remove the protective cap and the teat from the bottles
and remove the lid from the jars.
1.
2.
3.
4.
device setup
CAUTION
-This device is for home use only and is no way to be use outdoors.
-Always ensure to avoid any water over ow once a lled baby bottle is inside.
-Always use the bottle warmer with water inside it.
-Re-heating food is not recommended.

27
AUTOMATIC KEEP WARMING MODE
At the end of the cycle, indicator light will blink continuously showing
the bottle icon and the digits “37”. When the temperature goes down by
about 3 °C, the device will stop blinking which indicates that the warming
feature started again. Keep warming mode will run continuously unless
switched o manually or until water nishes
1.
2.
3.
4.
BABY FOOD JAR WARMING
Insert the basket and if necessary the adapter ring.
Remove the food jar cover. Place the jar inside the basket and ll the
tank with enough water to reach the same level of the food inside the
jar. Do not allow the water to enter the jar.
Plug the device into a power outlet and switch the device on by
pressing the on/o button. To select “Baby Food Warming”, press the
MENU button once, device will show food jar icon and default digits
10:00 will blink to indicate the time can be set by pressing the +/-
buttons (1 min each press or long press for a faster setting up to 20 min).
Once the time has been set, press the START button. When cycle ends,
device will beep 3 times and switch o automatically.
1.
2.
3.
4.
5.
6.
GENTLE DEFROST
Insert the basket and if necessary the adapter ring.
Fill the tank with 100ml of water as indicated. Do not overow.
Place the bottle inside the warmer.
Plug the device into a power outlet and switch the device on by
pressing the on/o button. To select “Gentle Defrost”, press the MENU
button twice, device will show GENTLE icon and default digits 00:30 *
will blink to indicate the time can be set by pressing the +/- buttons (10
minutes for each press or 30 minutes long press up to 3 hours)
Once the time has been set, press the START button. When cycle ends,
device will beep 3 times and switch o automatically.
To reach the feeding temperature of 37ºC start the “Baby Bottle
Warming” function.

28
NOTE
Digits on the display for this function will change from MIN:SEC to HRS:MIN,
i.e. 30 minutes will show 00:30 and 3 hours will show 3:00.
1.
2.
3.
4.
5.
STERILISING
Fill the tank with 100ml of water.
Insert the bottle parts / paciers or similar items directly inside the tank.
Put the sterilization cover.
Plug the device into a power outlet and switch the device on by
pressing the on/o button. To select “Sterilising and Fast Warming”, press
the MENU button three times, device will show the steam icon and
default digits 8:00 will blink.
There’s no need to adjust the time for this function, press the START
button. When cycle ends, device will beep 3 times and switch o
automatically.
1.
2.
3.
4.
5.
FAST WARMING
Insert the basket and if necessary the adapter ring.
Fill the tank with water as indicated. Do not overow.
Place the bottle without the teat and protective cap inside the bottle warmer.
Plug the device into a power outlet and switch the device on by
pressing the on/o button. To select “Sterilising and Fast Warming”, press
the MENU button three times, device will show the steam icon and
default digits 8:00 will blink to indicate the time can be set by pressing
the +/- buttons (30 sec for each press or 1 minute for long press up to
20 minutes.)
Once the time has been set, press the START button. When cycle ends,
device will beep 3 times and switch o automatically.
CAUTION
During sterilization, the lid heats up considerably. Avoid touching the lid
with your hands and use the handle on the top of the lid to remove it from
the bottle warmer. During sterilization, very hot steam comes out of the slots
on the top of the lid. Avoid approaching the lid with your hands and face, to
avoid being reached by the jet of steam and getting burns.

29
Timer allows to delay the start of the selected warming function
After selecting any of the previous functions, at the step 5, instead of
short pressing the START button, keep the button pressed for 2 sec.
Display will blink and will eventually show the TIMER icon.
Press the button +/- to set the timer at 15 minutes interval. Long press
will set the time at 1 hour interval up to 12 hours.
Once the timer is set, press the START button. Light will switch o until
the countdown nishes and the function will automatically start with a
beep sound.
•
•
•
timer function
NOTE
Timer can still be adjusted during the countdown.
general notes
MEMORY
This device is equipped with a memory function. If the device is turned
o and on again, Function 1 will remember the last time set. The function
remains stored for 12 hours when the device is turned o.
NOTE
When the device is on and on “Sterilising and Fast Warming”, pressing the
MENU button again, will go back to “Baby Bottle Warming”. When cycle is
nished take out the baby bottle to avoid the milk temperature to increase
further.
CONSECUTIVE CYCLES
Change the water between one use and the next.
BREASTMILK NUTRIENTS FRIENDLY
This device has been designed to gently warm up the milk and prevent
overheating in order to retain the breastmilk’s nutrients.

3030
The Nuvita 1170 Digital Bottle Warmer product and design are trademark by
Anteprima Brands International,
1, St. Luke’s Street, Gwardamangia,
PTA1020 Pieta, Malta, Europe.
Made in China
www.nuvitababy.com
Home use:
220V-240V / 400W
CE-EMC Certicate