Nuvoton NuMicro NuMaker-HMI-M2354 User manual

NuMaker-HMI-M2354
April. 15, 2022 Page 1of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
NuMicro® Family
Arm®Cortex®-M23-based Microcontroller
NuMaker-HMI-M2354
User Manual
Evaluation Board for NuMicro®M2354 Series
The information described in this document is the exclusive intellectual property of
Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.
Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system
design. Nuvoton assumes no responsibility for errors or omissions.
All data and specifications are subject to change without notice.
For additional information or questions, please contact: Nuvoton Technology Corporation.
www.nuvoton.com

NuMaker-HMI-M2354
April. 15, 2022 Page 2of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Table of Contents
1Overview.................................................................................... 7
2Features .................................................................................... 9
NuTFT Kit Board Features .................................................................. 9
NuMaker-M2354 Features .................................................................. 9
3NuTFT Kit Board Hardware Configuration .......................................... 10
Front View.....................................................................................10
Rear View.....................................................................................11
Extension Connectors.......................................................................12
3.3.1 Pin Assignment for Extension Connectors...................................................... 12
3.3.2 Pin Function Description........................................................................... 14
4NuTFT Kit BoardHardware Configuration........................................... 16
Front View.....................................................................................16
Rear View.....................................................................................17
Extension Connectors.......................................................................18
4.3.1 Pin Assignment for Extension Connectors...................................................... 18
4.3.2 Arduino UNO Compatible Extension Connectors ............................................. 24
Power Supply Configuration ...............................................................26
4.4.1 VIN Power Source.................................................................................. 26
4.4.2 5V Power Sources.................................................................................. 26
4.4.3 3.3 V Power Sources............................................................................... 26
4.4.4 1.8V Power Sources ............................................................................... 27
4.4.5 Power Connectors.................................................................................. 27
4.4.6 USB Connectors .................................................................................... 27
4.4.7 Power Switches..................................................................................... 27
4.4.8 Power Supply Models.............................................................................. 28
External Reference Voltage Connector ..................................................31
Ammeter Connector.........................................................................31
Push-Buttons .................................................................................31
MicroSD Card Slot...........................................................................31
SWD / ETM interface........................................................................32
LEDs...........................................................................................32
Wi-Fi Module (ESP-12) .....................................................................32
Nu-Link2-Me..................................................................................33

NuMaker-HMI-M2354
April. 15, 2022 Page 3of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
4.12.1 VCOM Switches..................................................................................... 33
4.12.2 Status LEDs ......................................................................................... 33
5Quick Start ............................................................................... 34
Toolchains Support..........................................................................34
Nuvoton Nu-Link Driver Installation.......................................................34
BSP Firmware Download...................................................................36
Hardware Setup..............................................................................36
Finding the Example Project...............................................................38
Executing the Project under Toolchains .................................................38
5.6.1 Keil MDK ............................................................................................. 38
5.6.2 IAR EWARM......................................................................................... 41
5.6.3 NuEclipse ............................................................................................ 43
6EmWin GUI Library PACKAGE Quick Start......................................... 49
emWin GUI Library Package Download .................................................49
Find the M2354 emWin Quick Start Guide ..............................................49
7NUTFT KIT BOARD SCHEMATICS ................................................. 50
NuTFT Kit Board.............................................................................50
PCB Placement ..............................................................................51
8NuMaker-M2354 Schematics ......................................................... 52
Nu-Link2-Me..................................................................................52
M2354 target Board .........................................................................53
USB 2.0 FS OTG ............................................................................54
Power Supply.................................................................................55
MCU Connector..............................................................................56
Arduino UNO Compatible Interface.......................................................57
MicroSD Card ................................................................................58
Wi-Fi Module (ESP-12) .....................................................................59
LCD interface.................................................................................60
PCB Placement ..............................................................................61
9REVISION HISTORY................................................................... 62

NuMaker-HMI-M2354
April. 15, 2022 Page 4of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
List of Figures
Figure 1-1 NuTFT Kit Board............................................................................................................. 7
Figure 1-2 NuMaker-M2354 Board .................................................................................................. 8
Figure 1-3 NuMaker-HMI-M2354..................................................................................................... 8
Figure 3-1 Front View of NuTFT Kit Board .................................................................................... 10
Figure 3-2 Rear View of NuTFT Kit Board..................................................................................... 11
Figure 3-3 NuTFT Kit Board Extension Connectors –Front View................................................. 12
Figure 3-4 NuTFT Kit Board Connectors –Rear View .................................................................. 13
Figure 4-1 Front View of NuMaker-M2354..................................................................................... 16
Figure 4-2 Rear View of NuMaker-M2354 ..................................................................................... 17
Figure 4-3 M2354 Extension Connectors ...................................................................................... 18
Figure 4-4 Arduino UNO Compatible Extension Connectors......................................................... 24
Figure 4-5 External Power Supply Sources on Nu-Link2-Me ........................................................ 28
Figure 4-6 External Power Supply Sources on M2354 target board ............................................. 29
Figure 4-7 Separate the Nu-Link2-Me from NuMaker-M2354 ....................................................... 30
Figure 4-8 Wiring between Ammeter Connector and Ammeter..................................................... 31
Figure 5-1 Nu-Link USB Driver Installation Setup.......................................................................... 34
Figure 5-2 Nu-Link USB Driver Installation.................................................................................... 35
Figure 5-3 Open VCOM Function .................................................................................................. 36
Figure 5-4 ICE USB Connector...................................................................................................... 36
Figure 5-5 Device Manger.............................................................................................................. 36
Figure 5-6 PuTTY Session Setting................................................................................................. 37
Figure 5-7 Blinky Project Folder Path ............................................................................................ 38
Figure 5-8 Debugger Setting in Options Window........................................................................... 38
Figure 5-9 Programming Setting in Options Window..................................................................... 39
Figure 5-10 Compile and Download the Project............................................................................ 39
Figure 5-11 Keil MDK Debug Mode............................................................................................... 40
Figure 5-12 Debug Message on Serial Port Terminal Windows.................................................... 40
Figure 5-13 IAR EWARM Window................................................................................................. 41
Figure 5-14 Compile and Download the Project............................................................................ 41
Figure 5-15 IAR EWARM Debug Mode ......................................................................................... 42
Figure 5-16 Debug Message on Serial Port Terminal Windows.................................................... 42
Figure 5-17 Import the Project in NuEclipse .................................................................................. 43
Figure 5-18 Import Projects Windows............................................................................................ 43
Figure 5-19 Build Project................................................................................................................ 44
Figure 5-20 Project Properties Settings......................................................................................... 44
Figure 5-21 Build Project................................................................................................................ 45

NuMaker-HMI-M2354
April. 15, 2022 Page 5of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Figure 5-22 Open Debug Configuration......................................................................................... 45
Figure 5-23 Main Tab Configuration .............................................................................................. 46
Figure 5-24 Debugger Tab Configuration ...................................................................................... 46
Figure 5-25 Startup Tab Configuration .......................................................................................... 47
Figure 5-26 NuEclipse Debug Mode.............................................................................................. 48
Figure 5-27 Debug Message on Serial Port Terminal Windows.................................................... 48
Figure 6-1 M2354 emWin Quick Start Guide Folder Path ............................................................. 49
Figure 7-1 NuTFT Kit Board Circuit ............................................................................................... 50
Figure 7-2 Front Placement ........................................................................................................... 51
Figure 7-3 Rear Placement............................................................................................................ 51
Figure 8-1 Nu-Link2-Me Circuit...................................................................................................... 52
Figure 8-2 M2354 Pin Assignment................................................................................................. 53
Figure 8-3 USB 2.0 FS OTG Circuit............................................................................................... 54
Figure 8-4 Power Circuit and Configurations................................................................................. 55
Figure 8-5 MCU connector............................................................................................................. 56
Figure 8-6 Arduino UNO Compatible Interface.............................................................................. 57
Figure 8-7 MicroSD Card Circuit.................................................................................................... 58
Figure 8-8 Wi-Fi Module Circuit ..................................................................................................... 59
Figure 8-9 LCD interface Circuit..................................................................................................... 60
Figure 8-10 Front Placement ......................................................................................................... 61
Figure 8-11 Rear Placement.......................................................................................................... 61

NuMaker-HMI-M2354
April. 15, 2022 Page 6of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
List of Tables
Table 3-1 NuTFT Kit Board Pin Function Description –NU1, NU2 and NU5................................ 14
Table 3-2 NuTFT Kit Board Pin Function Description –NU6 and NU7......................................... 15
Table 4-1 Extension Connectors.................................................................................................... 18
Table 4-2 M2354KJFAE Full-pin Extension Connectors and GPIO Function List......................... 23
Table 4-3 Arduino UNO Extension Connectors and M2354KJFAE Mapping GPIO List............... 25
Table 4-4 Vin Power Source.......................................................................................................... 26
Table 4-5 5V Power Sources......................................................................................................... 26
Table 4-6 3.3 V Power Sources..................................................................................................... 27
Table 4-7 1.8V Power Sources...................................................................................................... 27
Table 4-8 Power Connectors ......................................................................................................... 27
Table 4-9 USB Connectors ............................................................................................................ 27
Table 4-10 Power Switches ........................................................................................................... 28
Table 4-11 Supply External Power through Nu-Link2-Me ............................................................. 29
Table 4-12 Supply External Power for M2354 target board........................................................... 30
Table 4-13 External Reference Voltage Connector....................................................................... 31
Table 4-14 Ammeter Connector..................................................................................................... 31
Table 4-15 Push-Buttons ............................................................................................................... 31
Table 4-16 LEDs ............................................................................................................................ 32
Table 4-17 Optional Function of ESP-12....................................................................................... 32
Table 4-18 VCOM Function of Nu-Link2-Me.................................................................................. 33
Table 4-19 Status LEDs patterns of Nu-Link2-Me......................................................................... 33

NuMaker-HMI-M2354
April. 15, 2022 Page 7of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
1 OVERVIEW
The NuMaker-HMI-M2354 consists of two parts, a NuTFT Kit Board and a NuMaker-M2354 board. The
NuMaker-M2354 consists of two parts, a M2354 target board and an on-board Nu-Link2-Me debugger
and programmer. The NuMaker-M2354 is designed for secure evaluation, prototype development and
validation with power consumption monitoring function.
The M2354 target board is based on NuMicro M2354KJFAE. For the development flexibility, the M2354
target board provides the extension connectors of M2354KJFAE, the Arduino UNO compatible headers
and is able to adopt multiple power supply by external power connectors. Furthermore, the Nuvoton-
designed ammeter connector can measure the power consumption instantly, which is essential for the
prototype evaluation. The M2354 target board also has Wi-Fi connectivity on board for quick
development.
In addition, there is an attached on-board debugger and programmer “Nu-Link2-Me”. The Nu-Link2-
Me supports on-chip debugging, online and offline ICP programming via SWD interface. The Nu-
Link2-Me supports virtual COM (VCOM) port for printing debug messages on PC. Besides, the
programming status could be shown on the built-in LEDs. Lastly, the Nu-Link2-Me could be detached
from the evaluation board and become a stand-alone mass production programmer.
The NuTFT Kit Board is a daughter board that extends the NuMaker development boards. The NuTFT
Kit Board requires NuMaker development board as mother board to create a GUI development
platform. All Nuvoton NuMaker development boards support this kit board. It is designed for LCD
display or GUI evaluation, prototype development and validation. Besides, Nuvoton provides emWin
GUI library onNuMaker-M2354. By using NuMaker- M2354 as the mother board, user can create a
powerful and stunning graphics for the embedded system.
The NuTFT Kit Board is equipped with one SPI flash, one LCD panel with touch function, one five
direction joystick and two push buttons. NuTFT Kit Board pin arrangement is compatible with Arduino
UNO. The driver IC of the LCD panel is ILI9341, for more detailed information about the LCD panel,
please refer to the ILI9341 datasheet.
Figure 1-1 NuTFT Kit Board

NuMaker-HMI-M2354
April. 15, 2022 Page 8of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Figure 1-2 NuMaker-M2354 Board
Figure 1-3 NuMaker-HMI-M2354

NuMaker-HMI-M2354
April. 15, 2022 Page 9of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
2 FEATURES
NuTFT Kit Board Features
16 M bits (2 MB) SPI Flash * 1 (W25Q16CV)
24” (320x240) LCD Panel with 4-Wire ADC Touch Function (LCD Driver is Ili9341)
Five Direction Joystick * 1
Push Button * 2
Arduino UNO compatible extension connectors
NuMaker-M2354 Features
NuMicro M2354KJFAE microcontroller with function compatible with:
–M2354LJFAE
–M2354SJFAE
M2354KJFAE extension connectors
Arduino UNO compatible extension connectors
ETM (embedded trace macrocell) debug interface for instruction and data tracing of a
processor
Wi-Fi module for wireless application
MicroSD Card slot for T-Flash
Ammeter connector for measuring the microcontroller’s power consumption
Flexible board power supply:
–External VDD power connector
–Arduino UNO compatible extension connector Vin
–USB FS connector on M2354 target board
–ICE USB connector on Nu-Link2-Me
On-board Nu-Link2-Me debugger and programmer:
–Debug through SWD interface
–Online/offline programming
–Virtual COM port function

NuMaker-HMI-M2354
April. 15, 2022 Page 10 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
3 NUTFT KIT BOARD HARDWARE CONFIGURATION
Front View
Five
Direction
Joystick
Switch Button
TFT LCD Panel with
Touch Function
TFT LCD Panel with
Touch Function
Arduino compatible
interface connectors
Arduino compatible
interface connectors
Arduino compatible
interface connectors
Arduino compatible
interface connectors
Figure 3-1 Front View of NuTFT Kit Board
Figure 3-1 shows the main components and connectors from the front side of NuTFT Kit Board. The
following lists components and connectors from the front view:
Five Direction Joystick (J3)
–There are five dimensions: up, down, left, right and middle in five-direction joystick.
Push Button (SW7 and SW8)
2.4” (320x240) LCD Panel with 4-Wire ADC Touch Function (LCD Driver is Ili9341) (J7)
–This TFT LCD panel with 4-wire ADC touch function is equipped with driver IC,
ILI9341.
–LCD Control Interface: SPI
–Touch Function Interface: ADC * 4
–Panel Size: 2.4”
–Panel Resolution: 320x240
Arduino UNO Compatible Interface Connectors (NU1, NU2, NU5 and NU6)

NuMaker-HMI-M2354
April. 15, 2022 Page 11 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Rear View
shows the main components and connectors from the rear side of NuTFT Kit Board.
The following lists components and connectors from the rear view:
16 Mbits (2 MB) SPI Flash * 1 (W25Q16CV) (U1)
Arduino UNO Compatible Interface Connectors (NU1, NU2, NU5, NU6 and NU7)
SPI Flash
Arduino compatible
interface connectors
Arduino compatible
interface connectors
Arduino compatible
interface connectors
Arduino compatible
interface connectors
Arduino compatible
interface connectors
Arduino compatible
interface connectors
Figure 3-2 Rear View of NuTFT Kit Board

NuMaker-HMI-M2354
April. 15, 2022 Page 12 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Extension Connectors
3.3.1 Pin Assignment for Extension Connectors
NuTFT Kit Board is equipped with one SPI flash, one LCD panel with touch function, one five direction
joystick and two push buttons for developing and verifying some special feature. Besides, the pin
arrangement of NuTFT Kit Board is compatible with Arduino UNO.
NC
NC
NC
3.3V
NC
GND
GND
NC
ADC-YU
ADC-XL
ADC-YD
ADC-XR
Button-SW7
Button-SW8
NC
NC
NC
VSS
SPIFlash-CLK
SPIFlash-MISO0
SPIFlash-MOSI0
SPIFlash-SS
SPIFlash-MOSI1
SPIFlash-MISO1
LCM_LED
Joystick-R
Joystick-U
Joystick-L
Joystick-D
Joystick-M
LCM_RESET
LCM_DC
Figure 3-3 NuTFT Kit Board Extension Connectors –Front View

NuMaker-HMI-M2354
April. 15, 2022 Page 13 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
LCM_SPI_SS LCM_RESET LCM_SPI_CLK LCM_SPI_MISO
GPIO GND LCM_SPI_MOSI 3.3V
NC
NC
NC
3.3V
NC
GND
GND
NC
ADC-YU
ADC-XL
ADC-YD
ADC-XR
Button-SW7
Button-SW8
NC
NC
NC
VSS
SPIFlash-CLK
SPIFlash-MISO0
SPIFlash-MOSI0
SPIFlash-SS
SPIFlash-MOSI1
SPIFlash-MISO1
LCM_LED
Joystick-R
Joystick-U
Joystick-L
Joystick-D
Joystick-M
LCM_RESET
LCM_DC
Figure 3-4 NuTFT Kit Board Connectors –Rear View

NuMaker-HMI-M2354
April. 15, 2022 Page 14 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
3.3.2 Pin Function Description
There is few different between NuMaker pin define and Arduino UNO pin define. The pin define of
NU7 of Arduino is same as D11, D12, D13 (SPI function) and there is 1 set of SPI. The pin define of
NU7 of NuMaker is another SPI function and there are 2 sets of SPI. If user wants to operate the
NuTFT Kit Board on Arduino UNO, because it share one SPI, it recommends that control Flash and
panel by switching the SPI Flash –SS0(D10) and LCM_SPI_SS.
Header
Arduino UNO
Pin Define
NuMaker
Pin Define
NuTFT Kit Board Function
NU1
NC
NC
NC
IOREF
IOREF
NC
RESET
RESET
NC
3.3V
3.3V
Power for NuTFT Kit Board
5V
5V
NC
GND
GND
GND
GND
GND
GND
Vin
Vin
NC
NU2
A0
A0
4 wired ADC Touch Panel –YU
A1
A1
4 wired ADC Touch Panel –XL
A2
A2
4 wired ADC Touch Panel –YD
A3
A3
4 wired ADC Touch Panel –XR
A4
A4
SW7 Push Button
A5
A5
SW8 Push Button
NU5
D0
D0
LCM_DC
D1
D1
LCM_RESET
D2
D2
Five direction joystick –Middle
D3
D3
Five direction joystick –Down
D4
D4
Five direction joystick –Left
D5
D5
Five direction joystick –Up
D6
D6
Five direction joystick –Right
D7
D7
LCM_EN (PWM)
Table 3-1 NuTFT Kit Board Pin Function Description –NU1, NU2 and NU5

NuMaker-HMI-M2354
April. 15, 2022 Page 15 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Header
Arduino UNO
Pin Define
NuMaker Pin
Define
NuTFT Kit Board Function
NU6
D8
D8
SPI Flash –MISO1
D9
D9
SPI Flash –MOSI1
D10
D10 (SPI0)
SPI Flash –SS0
D11
D11 (SPI0)
SPI Flash –MOSI0
D12
D12 (SPI0)
SPI Flash –MISO0
D13
D13 (SPI0)
SPI Flash –CLK0
GND
GND
GND
AREF
AREF
NC
SDA
SDA
NC
SCL
SCL
NC
NU7
D12
SPI_MISO (SPI1)
LCM_SPI_MISO
5V
5V
3.3V
D13
SPI_CLK (SPI1)
LCM_SPI_CLK
D11
SPI_MOSI (SPI1)
LCM_SPI_MOSI
RESET
RESET
LCM Panel Reset
GND
GND
GND
--
SPI_SS (SPI1)
LCM_SPI_SS
--
GPIO
GPIO
Table 3-2 NuTFT Kit Board Pin Function Description –NU6 and NU7

NuMaker-HMI-M2354
April. 15, 2022 Page 16 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
4 NUTFT KIT BOARDHARDWARE CONFIGURATION
Front View
Figure 4-1 Front View of NuMaker-M2354
Figure 4-1 shows the main components and connectors from the front side of NuMaker-M2354. The
following lists components and connectors from the front view:
Target Chip: M2354KJFAE (U1)
USB PWR Connector (J2)
Arduino UNO Compatible Extension Connectors (NU1, NU2, NU3, NU4)
M2354 Extension Connectors (JP6, JP7, JP8, JP9)
External VDD Power Connector
External VSS Power Connector
External VREF Connector (VREF1)
VDD Switch (SW4)
Ammeter Connector (AMMETER)
Reset Button (SW1) and push Button (SW2)
Power LED and PD2/3 LED (LEDG1 and LEDR1)
Wi-Fi Module
COM/SEG LCD interface (JLCD)
Nu-Link2-Me
–VCOM Switch
–ICE Chip: M48SSIDAE (ICEU2)
–ICE USB Connector (ICEJ3)
–ICE Status LED (ICES0, ICES1, ICES2, ICES3)
–Off-line Program Button (ICESW1)

NuMaker-HMI-M2354
April. 15, 2022 Page 17 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Rear View
Figure 4-2 shows the main components and connectors from the rear side of NuMaker-M2354.
The following lists components and connectors from the rear view:
Nu-Link2-Me
–MCUVCC Power Switch (ICEJPR1)
–ICEVCC Power Switch (ICEJPR2)
MicroSD Card Slot: T-Flash Slot
Figure 4-2 Rear View of NuMaker-M2354

NuMaker-HMI-M2354
April. 15, 2022 Page 18 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Extension Connectors
Table 4-1 presents the extension connectors.
Connector
Description
JP6, JP7, JP8 and JP9
Full pins extension connectors on the NuMaker-M2354.
NU1, NU2, NU3 and
NU4
Arduino UNO compatible pins on the NuMaker-M2354.
Table 4-1 Extension Connectors
4.3.1 Pin Assignment for Extension Connectors
The NuMaker-M2354 provides the M2354 target chip on board and full pins extension connectors (JP6,
JP7, JP8 and JP9). Figure 4-3 shows the M2354 extension connectors.
JP6
Pin1 ~ Pin32
JP9
Pin97 ~ Pin128
JP8 Pin33 ~ Pin64
JP7 Pin65 ~ Pin96
Figure 4-3 M2354 Extension Connectors

NuMaker-HMI-M2354
April. 15, 2022 Page 19 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Header
M2354KJFAE
Pin No.
Function
JP6
JP6.1
1
PB.5 / EADC0_CH5 / ACMP1_N / EBI_ADR0 / SD0_DAT3 / SPI1_MISO / I2C0_SCL / UART5_TXD
/ USCI1_CTL0 / SC0_CLK / I2S0_BCLK / EPWM0_CH0 / UART2_TXD / TM0 / INT0
JP6.2
2
PB.4 / EADC0_CH4 / ACMP1_P1 / EBI_ADR1 / SD0_DAT2 / SPI1_MOSI / I2C0_SDA /
UART5_RXD / USCI1_CTL1 / SC0_DAT / I2S0_MCLK / EPWM0_CH1 / UART2_RXD / TM1 / INT1
JP6.3
3
PB.3 / EADC0_CH3 / ACMP0_N / EBI_ADR2 / SD0_DAT1 / SPI1_CLK / UART1_TXD /
UART5_nRTS / USCI1_DAT1 / SC0_RST / I2S0_DI / EPWM0_CH2 / I2C1_SCL / TM4 / TM2 / INT2
JP6.4
4
PB.2 / EADC0_CH2 / ACMP0_P1 / EBI_ADR3 / SD0_DAT0 / SPI1_SS / UART1_RXD /
UART5_nCTS / USCI1_DAT0 / SC0_PWR / I2S0_DO / EPWM0_CH3 / I2C1_SDA / TM5 / TM3 /
INT3
JP6.5
5
PC.12 / EBI_ADR4 / UART0_TXD / I2C0_SCL / SPI3_MISO / SC0_nCD / ECAP1_IC2 /
EPWM1_CH0 / ACMP0_O
JP6.6
6
PC.11 / EBI_ADR5 / UART0_RXD / I2C0_SDA / SPI3_MOSI / ECAP1_IC1 / EPWM1_CH1 /
ACMP1_O
JP6.7
7
PC.10 / EBI_ADR6 / SPI3_CLK / UART3_TXD / ECAP1_IC0 / EPWM1_CH2
JP6.8
8
PC.9 / EBI_ADR7 / SPI3_SS / UART3_RXD / EPWM1_CH3
JP6.9
9
PB.1 / EADC0_CH1 / EBI_ADR8 / SD0_CLK / SPI1_I2SMCLK / SPI3_I2SMCLK / UART2_TXD /
USCI1_CLK / I2C1_SCL / I2S0_LRCK / EPWM0_CH4 / EPWM1_CH4 / EPWM0_BRAKE0 /
QSPI0_MISO1
JP6.10
10
PB.0 / EADC0_CH0 / EBI_ADR9 / SD0_CMD / SPI2_I2SMCLK / UART2_RXD / SPI0_I2SMCLK /
I2C1_SDA / EPWM0_CH5 / EPWM1_CH5 / EPWM0_BRAKE1 / QSPI0_MOSI1
JP6.11
11
VSS
JP6.12
12
VDD
JP6.13
13
PA.11 / ACMP0_P0 / EBI_nRD / SC2_PWR / SPI2_SS / USCI0_CLK / I2C2_SCL / BPWM0_CH0 /
EPWM0_SYNC_OUT / TM0_EXT / DAC1_ST
JP6.14
14
PA.10 / ACMP1_P0 / EBI_nWR / SC2_RST / SPI2_CLK / USCI0_DAT0 / I2C2_SDA / BPWM0_CH1
/ QEI1_INDEX / ECAP0_IC0 / TM1_EXT / DAC0_ST
JP6.15
15
PA.9 / EBI_MCLK / SC2_DAT / SPI2_MISO / USCI0_DAT1 / UART1_TXD / BPWM0_CH2 / QEI1_A
/ ECAP0_IC1 / TM4_EXT / TM2_EXT
JP6.16
16
PA.8 / EBI_ALE / SC2_CLK / SPI2_MOSI / USCI0_CTL1 / UART1_RXD / BPWM0_CH3 / QEI1_B /
ECAP0_IC2 / TM5_EXT / TM3_EXT / INT4
JP6.17
17
PC.13 / EBI_ADR10 / SC2_nCD / SPI2_I2SMCLK / USCI0_CTL0 / UART2_TXD / BPWM0_CH4 /
CLKO / EADC0_ST
JP6.18
18
PD.12 / EBI_nCS0 / UART2_RXD / BPWM0_CH5 / QEI0_INDEX / CLKO / EADC0_ST / INT5
JP6.19
19
PD.11 / EBI_nCS1 / UART1_TXD / CAN0_TXD / QEI0_A / INT6
JP6.20
20
PD.10 / EBI_nCS2 / UART1_RXD / CAN0_RXD / QEI0_B / INT7
JP6.21
21
PG.2 / EBI_ADR11 / SPI2_SS / I2C0_SMBAL / I2C1_SCL / TM0 / LCD_SEG39
JP6.22
22
PG.3 / EBI_ADR12 / SPI2_CLK / I2C0_SMBSUS / I2C1_SDA / TM1 / LCD_SEG38
JP6.23
23
PG.4 / EBI_ADR13 / SPI2_MISO / TM4 / TM2 / LCD_SEG37
JP6.24
24
PF.11 / EBI_ADR14 / SPI2_MOSI / UART5_TXD / TAMPER5 / TM5 / TM3
JP6.25
25
PF.10 / EBI_ADR15 / SC0_nCD / I2S0_BCLK / SPI0_I2SMCLK / UART5_RXD / TAMPER4
JP6.26
26
PF.9 / EBI_ADR16 / SC0_PWR / I2S0_MCLK / SPI0_SS / UART5_nRTS / TAMPER3
JP6.27
27
PF.8 / EBI_ADR17 / SC0_RST / I2S0_DI / SPI0_CLK / UART5_nCTS / TAMPER2
JP6.28
28
PF.7 / EBI_ADR18 / SC0_DAT / I2S0_DO / SPI0_MISO / UART4_TXD / TAMPER1
JP6.29
29
PF.6 / EBI_ADR19 / SC0_CLK / I2S0_LRCK / SPI0_MOSI / UART4_RXD / EBI_nCS0 /
SPI3_I2SMCLK / TAMPER0
JP6.30
30
VBAT
JP6.31
31
PF.5 / UART2_RXD / UART2_nCTS / EPWM0_CH0 / BPWM0_CH4 / EPWM0_SYNC_OUT /
X32_IN / EADC0_ST

NuMaker-HMI-M2354
April. 15, 2022 Page 20 of 63 Rev 1.00
NUMAKER-HMI-M2354 USER MANUAL
Maker Nu-mbed NUC472 User Manual
Header
M2354KJFAE
Pin No.
Function
JP6.32
32
PF.4 / UART2_TXD / UART2_nRTS / EPWM0_CH1 / BPWM0_CH5 / X32_OUT
JP8
JP8.1
33
PH.4 / EBI_ADR3 / SPI1_MISO / LCD_SEG36
JP8.2
34
PH.5 / EBI_ADR2 / SPI1_MOSI / LCD_SEG35
JP8.3
35
PH.6 / EBI_ADR1 / SPI1_CLK / LCD_SEG34
JP8.4
36
PH.7 / EBI_ADR0 / SPI1_SS / LCD_SEG33
JP8.5
37
PF.3 / EBI_nCS0 / UART0_TXD / I2C0_SCL / XT1_IN / BPWM1_CH0
JP8.6
38
PF.2 / EBI_nCS1 / UART0_RXD / I2C0_SDA / QSPI0_CLK / XT1_OUT / BPWM1_CH1
JP8.7
39
VSS
JP8.8
40
VDD
JP8.9
41
PE.8 / EBI_ADR10 / I2S0_BCLK / SPI2_CLK / USCI1_CTL1 / UART2_TXD / EPWM0_CH0 /
EPWM0_BRAKE0 / ECAP0_IC0 / TRACE_DATA3 / LCD_SEG32
JP8.10
42
PE.9 / EBI_ADR11 / I2S0_MCLK / SPI2_MISO / USCI1_CTL0 / UART2_RXD / EPWM0_CH1 /
EPWM0_BRAKE1 / ECAP0_IC1 / TRACE_DATA2 / LCD_SEG31
JP8.11
43
PE.10 / EBI_ADR12 / I2S0_DI / SPI2_MOSI / USCI1_DAT0 / UART3_TXD / EPWM0_CH2 /
EPWM1_BRAKE0 / ECAP0_IC2 / TRACE_DATA1 / LCD_SEG30
JP8.12
44
PE.11 / EBI_ADR13 / I2S0_DO / SPI2_SS / USCI1_DAT1 / UART3_RXD / UART1_nCTS /
EPWM0_CH3 / EPWM1_BRAKE1 / ECAP1_IC2 / TRACE_DATA0
JP8.13
45
PE.12 / EBI_ADR14 / I2S0_LRCK / SPI2_I2SMCLK / USCI1_CLK / UART1_nRTS / EPWM0_CH4 /
ECAP1_IC1 / TRACE_CLK
JP8.14
46
PE.13 / EBI_ADR15 / I2C0_SCL / UART4_nRTS / UART1_TXD / EPWM0_CH5 / EPWM1_CH0 /
BPWM1_CH5 / ECAP1_IC0
JP8.15
47
PC.8 / EBI_ADR16 / I2C0_SDA / UART4_nCTS / UART1_RXD / EPWM1_CH1 / BPWM1_CH4
JP8.16
48
PC.7 / EBI_AD9 / SPI1_MISO / UART4_TXD / SC2_PWR / UART0_nCTS / I2C1_SMBAL /
EPWM1_CH2 / BPWM1_CH0 / TM0 / INT3
JP8.17
49
PC.6 / EBI_AD8 / SPI1_MOSI / UART4_RXD / SC2_RST / UART0_nRTS / I2C1_SMBSUS /
EPWM1_CH3 / BPWM1_CH1 / TM1 / INT2
JP8.18
50
PA.7 / EBI_AD7 / SPI1_CLK / SC2_DAT / UART0_TXD / I2C1_SCL / TM4 / EPWM1_CH4 /
BPWM1_CH2 / ACMP0_WLAT / TM2 / INT1
JP8.19
51
PA.6 / EBI_AD6 / SPI1_SS / SC2_CLK / UART0_RXD / I2C1_SDA / TM5 / EPWM1_CH5 /
BPWM1_CH3 / ACMP1_WLAT / TM3 / INT0
JP8.20
52
VSS
JP8.21
53
VDD
JP8.22
54
LDO_CAP
JP8.23
55
PA.5 / QSPI0_MISO1 / SPI1_I2SMCLK / SC2_nCD / UART0_nCTS / UART5_TXD / I2C0_SCL /
CAN0_TXD / UART0_TXD / BPWM0_CH5 / EPWM0_CH0 / QEI0_INDEX / LCD_SEG29
JP8.24
56
PA.4 / QSPI0_MOSI1 / SPI0_I2SMCLK / SC0_nCD / UART0_nRTS / UART5_RXD / I2C0_SDA /
CAN0_RXD / UART0_RXD / BPWM0_CH4 / EPWM0_CH1 / QEI0_A / LCD_SEG28
JP8.25
57
PA.3 / QSPI0_SS / SPI0_SS / SC0_PWR / UART4_TXD / UART1_TXD / I2C1_SCL / I2C0_SMBAL
/ LCD_SEG27 / BPWM0_CH3 / EPWM0_CH2 / QEI0_B / EPWM1_BRAKE1
JP8.26
58
PA.2 / QSPI0_CLK / SPI0_CLK / SC0_RST / UART4_RXD / UART1_RXD / I2C1_SDA /
I2C0_SMBSUS / LCD_SEG26 / BPWM0_CH2 / EPWM0_CH3
JP8.27
59
PA.1 / QSPI0_MISO0 / SPI0_MISO / SC0_DAT / UART0_TXD / UART1_nCTS / I2C2_SCL /
LCD_SEG25 / BPWM0_CH1 / EPWM0_CH4 / DAC1_ST
JP8.28
60
PA.0 / QSPI0_MOSI0 / SPI0_MOSI / SC0_CLK / UART0_RXD / UART1_nRTS / I2C2_SDA /
LCD_SEG24 / BPWM0_CH0 / EPWM0_CH5 / DAC0_ST
JP8.29
61
VDDIO
JP8.30
62
PE.14 / EBI_AD8 / UART2_TXD / CAN0_TXD / LCD_SEG23
JP8.31
63
PE.15 / EBI_AD9 / UART2_RXD / CAN0_RXD / LCD_SEG22