Nuvoton Numicro NuMaker-NUC1311L User manual

NuMaker-NUC1311L
Aug. 12, 2022 Page 1of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
NuMicro® Family
Arm®Cortex®-M0-based Microcontroller
NuMaker-NUC1311L
User Manual
Evaluation Board for NuMicro®NUC1311 Series
The information described in this document is the exclusive intellectual property of
Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.
Nuvoton is providing this document only for reference purposes of NuMicro microcontroller and
microprocessor based system design. Nuvoton assumes no responsibility for errors or omissions.
All data and specifications are subject to change without notice.
For additional information or questions, please contact: Nuvoton Technology Corporation.
www.nuvoton.com

NuMaker-NUC1311L
Aug. 12, 2022 Page 2of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
Table of Contents
1OVERVIEW .........................................................................................................7
2FEATURES......................................................................................................... 8
3HARDWARE CONFIGURATION.......................................................................9
3.1 Front View ....................................................................................................................... 9
3.2 Rear View ......................................................................................................................10
3.3 Extension Connectors .................................................................................................11
3.3.1 Pin Assignment for Extension Connectors ................................................................. 11
3.3.2 Arduino UNO Compatible Extension Connectors ..................................................... 14
3.4 Power Supply Configuration.......................................................................................16
3.4.1 VIN Power Source .......................................................................................................... 16
3.4.2 5 V Power Sources......................................................................................................... 16
3.4.3 3.3 V Power Sources ..................................................................................................... 17
3.4.4 1.8 V Power Sources ..................................................................................................... 17
3.4.5 Power Connectors .......................................................................................................... 17
3.4.6 USB Connectors ............................................................................................................. 18
3.4.7 Power Switches .............................................................................................................. 18
3.4.8 Power Supply Models .................................................................................................... 18
3.5 External Reference Voltage Connector ....................................................................22
3.6 Ammeter Connector.....................................................................................................23
3.7 Push Buttons.................................................................................................................24
3.8 LEDs...............................................................................................................................25
3.9 Nu-Link2-Me..................................................................................................................26
3.9.1 VCOM Switches.............................................................................................................. 26
3.9.2 Status LEDs..................................................................................................................... 27
4QUICK START..................................................................................................28
4.1 Toolchains Supporting .................................................................................................28
4.2 Nuvoton Nu-Link Driver Installation...........................................................................29
4.3 BSP Firmware Download............................................................................................31
4.4 Hardware Setup............................................................................................................32
4.5 Find the Example Project............................................................................................34
4.6 Execute the Project under Toolchains ......................................................................35
4.6.1 Keil MDK .......................................................................................................................... 35
4.6.2 IAR EWARM.................................................................................................................... 39
4.6.3 NuEclipse......................................................................................................................... 41
5NUMAKER-NUC1311L SCHEMATICS...........................................................47
5.1 Nu-Link2-Me..................................................................................................................47

NuMaker-NUC1311L
Aug. 12, 2022 Page 3of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
5.2 NUC1311 Target Board ...............................................................................................48
5.3 Extension Connectors .................................................................................................49
5.4 PCB Placement ............................................................................................................50
6REVISION HISTORY........................................................................................51

NuMaker-NUC1311L
Aug. 12, 2022 Page 4of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
List of Figures
Figure 1-1 NuMaker-NUC1311L Evaluation Board..........................................................................7
Figure 3-1 Front View of NuMaker-NUC1311L ................................................................................9
Figure 3-2 Rear View of NuMaker- NUC1311L..............................................................................10
Figure 3-3 NUC1311LD2AE Extension Connectors.......................................................................11
Figure 3-4 Arduino UNO Compatible Extension Connectors.........................................................14
Figure 3-5 External Power Supply Sources on Nu-Link2-Me.........................................................18
Figure 3-6 External Power Supply Sources on NUC1311 Target Board .......................................19
Figure 3-7 Detach the Nu-Link2-Me from NuMaker- NUC1311L...................................................20
Figure 3-8 Wiring between Ammeter Connector and Ammeter .....................................................23
Figure 4-1 Nu-Link USB Driver Installation Setup ..........................................................................29
Figure 4-2 Nu-Link USB Driver Installation.....................................................................................30
Figure 4-3 Open VCOM Function...................................................................................................32
Figure 4-4 ICE USB Connector ......................................................................................................32
Figure 4-5 Device Manger ..............................................................................................................33
Figure 4-6 PuTTY Session Setting.................................................................................................33
Figure 4-7 Template Project Folder Path .......................................................................................34
Figure 4-8 Warning Message of “Device not found”.......................................................................35
Figure 4-9 Project File Migrate to Version 5 Format.......................................................................35
Figure 4-10 Debugger Setting in Options Window .........................................................................36
Figure 4-11 Programming Setting in Options Window ...................................................................36
Figure 4-12 Compile and Download the Project.............................................................................37
Figure 4-13 Keil MDK Debug Mode................................................................................................38
Figure 4-14 Debug Message on Serial Port Terminal Windows ....................................................38
Figure 4-15 IAR EWARM Window..................................................................................................39
Figure 4-16 Compile and Download the Project.............................................................................39
Figure 4-17 IAR EWARM Debug Mode..........................................................................................40
Figure 4-18 Debug Message on Serial Port Terminal Windows ....................................................40
Figure 4-19 Import the Project in NuEclipse...................................................................................41
Figure 4-20 Import Projects Windows.............................................................................................41
Figure 4-21 Open Project Properties Window................................................................................42
Figure 4-22 Project Properties Settings..........................................................................................42
Figure 4-23 Build Project ................................................................................................................43
Figure 4-24 Open Debug Configuration .........................................................................................43
Figure 4-25 Main Tab Configuration...............................................................................................44
Figure 4-26 Debugger Tab Configuration.......................................................................................44
Figure 4-27 Startup Tab Configuration...........................................................................................45

NuMaker-NUC1311L
Aug. 12, 2022 Page 5of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
Figure 4-28 NuEclipse Debug Mode...............................................................................................46
Figure 4-29 Debug Message on Serial Port Terminal Windows ....................................................46
Figure 5-1 Nu-Link2-Me Circuit.......................................................................................................47
Figure 5-2 NUC1311 Target Board Circuit .....................................................................................48
Figure 5-3 Extension Connectors Circuit........................................................................................49
Figure 5-4 Front Placement............................................................................................................50
Figure 5-5 Rear Placement.............................................................................................................50

NuMaker-NUC1311L
Aug. 12, 2022 Page 6of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
List of Tables
Table 3-1 Extension Connectors ....................................................................................................11
Table 3-2 NUC1311LD2AE Full-pin Extension Connectors and GPIO Function List ....................12
Table 3-3 Arduino UNO Extension Connectors and NUC1311LD2AE Mapping GPIO List ..........15
Table 3-4 Vin Power Source...........................................................................................................16
Table 3-5 5 V Power Sources.........................................................................................................16
Table 3-6 3.3 V Power Sources......................................................................................................17
Table 3-7 1.8 V Power Sources......................................................................................................17
Table 3-8 Power Connectors..........................................................................................................17
Table 3-9 USB Connectors.............................................................................................................18
Table 3-10 Power Switches............................................................................................................18
Table 3-11 Supply External Power through Nu-Link2-Me..............................................................19
Table 3-12 Supply External Power for NUC1311 Target Board.....................................................21
Table 3-13 External Reference Voltage Connector........................................................................22
Table 3-14 Ammeter Connector .....................................................................................................23
Table 3-15 Push Buttons ................................................................................................................24
Table 3-16 LEDs.............................................................................................................................25
Table 3-17 VCOM Function of Nu-Link2-Me ..................................................................................26
Table 3-18 Operation Status LED Patterns....................................................................................27

NuMaker-NUC1311L
Aug. 12, 2022 Page 7of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
1 OVERVIEW
The NuMaker-NUC1311L is an evaluation board for NuMicro NUC1311LC and NUC1311LD
microcontrollers. The NuMaker-NUC1311L consists of two parts: an NUC1311 target board and an on-
board Nu-Link2-Me debugger and programmer. The NuMaker-NUC1311L is designed for project
evaluation, prototype development and validation with power consumption monitoring function.
The NUC1311 target board is based on NuMicroNUC1311LD2AE. For the development flexibility, the
NUC1311 target board provides the extension connectors, the Arduino UNO compatible headers and
the capability of adopting multiple power supplies. Furthermore, the Nuvoton-designed ammeter
connector can measure the power consumption instantly, which is essential for the prototype evaluation.
In addition, there is an attached on-board debugger and programmer “Nu-Link2-Me”. The Nu-Link2-Me
supports on-chip debugging, online and offline ICP programming via SWD interface. The Nu-Link2-Me
supports virtual COM (VCOM) port for printing debug messages on PC. Besides, the programming
status could be shown on the built-in LEDs. Lastly, the Nu-Link2-Me could be detached from the
evaluation board and become a stand-alone mass production programmer.
Figure 1-1 NuMaker-NUC1311L Evaluation Board

NuMaker-NUC1311L
Aug. 12, 2022 Page 8of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
2 FEATURES
⚫NuMicro NUC1311LD2AE used as main microcontroller with function compatible with:
–NUC1311LC2AE
–NUC1311LD2AE
⚫NUC1311LD2AE full pins extension connectors
⚫Arduino UNO compatible extension connectors
⚫Ammeter connector for measuring the microcontroller’s power consumption
⚫Flexible board power supply:
–External VDD power connector
–Arduino UNO compatible extension connector Vin
–USB FS connector on NUC1311 target board
–ICE USB connector on Nu-Link2-Me
⚫On-board Nu-Link2-Me debugger and programmer:
–Debug through SWD interface
–Online/offline programming
–Virtual COM port function

NuMaker-NUC1311L
Aug. 12, 2022 Page 9of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
3 HARDWARE CONFIGURATION
3.1 Front View
Figure 3-1 Front View of NuMaker-NUC1311L
Figure 3-1 shows the maincomponents and connectors fromthe front side of NuMaker-NUC1311L. The
following lists components and connectors from the front view:
⚫Target chip:NUC1311LD2AE (U1)
⚫USB PWR Connector (J2)
⚫Arduino UNO Compatible Extension Connectors (NU1, NU2, NU3, NU4)
⚫NUC1311 Extension Connectors (JP3, JP4, JP5 and JP6)
⚫External VDD Power Connector (JP1)
⚫External VSS Power Connector (JP2)
⚫External VREF Connector (VREF1)
⚫VDD Switch (SW2)
⚫Ammeter Connector (AMMETER)
⚫Reset Button (SW1)
⚫Power LED and PB12 LED (LEDG1 and LEDR1)
⚫Nu-Link2-Me
–VCOM Switch
–ICE Chip: M48SSIDAE (ICEU2)
–ICE USB Connector (ICEJ3)
–ICE Status LED (ICES0, ICES1, ICES2, ICES3)
–Off-line Program Button (ICESW1)

NuMaker-NUC1311L
Aug. 12, 2022 Page 10 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
3.2 Rear View
Figure 3-2 shows the main components and connectors from the rear side of NuMaker-NUC1311L.
The following lists components and connectors from the rear view:
⚫Nu-Link2-Me
–MCUVCC Power Switch (ICEJPR1)
–ICEVCC Power Switch (ICEJPR2)
Figure 3-2 Rear View of NuMaker-NUC1311L

NuMaker-NUC1311L
Aug. 12, 2022 Page 11 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
3.3 Extension Connectors
Table 3-1 presents the extension connectors.
Connector
Description
JP3, JP4, JP5 and JP6
Full pins extension connectors on the NuMaker-NUC1311L.
NU1, NU2, NU3 and
NU4
Arduino UNO compatible pins on the NuMaker- NUC1311L.
Table 3-1 Extension Connectors
3.3.1 Pin Assignment for Extension Connectors
The NuMaker-NUC1311L provides the NUC1311LD2AE onboard and extension connectors (JP3, JP4,
JP5 and JP6). Figure 3-3 shows the NUC1311LD2AE extension connectors.
Figure 3-3 NUC1311LD2AE Extension Connectors

NuMaker-NUC1311L
Aug. 12, 2022 Page 12 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
Header
NUC1311LD2AE
Pin
No.
Function
JP3
JP3.1
1
PB.12 / CLKO
JP3.2
2
PF.5 / I2C0_SCL / PWM1_CH5
JP3.3
3
PF.4 / I2C0_SDA / PWM1_CH4
JP3.4
4
PA.11 / PWM1_CH3
JP3.5
5
PA.10 / PWM1_CH2
JP3.6
6
PA.9 / I2C0_SCL / UART1_nCTS
JP3.7
7
PA.8 / I2C0_SDA / UART1_nRTS
JP3.8
8
PB.4 / UART1_RXD
JP3.9
9
PB.5 / UART1_TXD
JP3.10
10
LDO_CAP
JP3.11
11
VDD
JP3.12
12
VSS
JP5
JP5.1
13
PB.0 / UART0_RXD
JP5.2
14
PB.1 / UART0_TXD
JP5.3
15
PB.2 / UART0_nRTS / TM2_EXT / TM2 / PWM1_BRAKE1
JP5.4
16
PB.3 / UART0_nCTS / TM3_EXT / TM3 / PWM1_BRAKE0
JP5.5
17
PD.6 / CAN0_RXD
JP5.6
18
PD.7 / CAN0_TXD
JP5.7
19
PD.14 / UART2_RXD
JP5.8
20
PD.15 / UART2_TXD
JP5.9
21
PC.3 / SPI0_MOSI0
JP5.10
22
PC.2 / SPI0_MISO0
JP5.11
23
PC.1 / SPI0_CLK
JP5.12
24
PC.0 / SPI0_SS0
JP4
JP4.1
25
PA.15 / PWM0_CH3
JP4.2
26
PA.14 / PWM0_CH2
JP4.3
27
PA.13 / PWM0_CH1
JP4.4
28
PA.12 / PWM0_CH0
JP4.5
29
PF.7 / ICE_DAT
JP4.6
30
PF.6 / ICE_CLK
JP4.7
31
AVSS
JP4.8
32
PA.0 / ADC_CH0 / PWM0_CH4

NuMaker-NUC1311L
Aug. 12, 2022 Page 13 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
Header
NUC1311LD2AE
Pin
No.
Function
JP4.9
33
PA.1 / ADC_CH1 / PWM0_CH5
JP4.10
34
PA.2 / ADC_CH2 / PWM1_CH0 / UART3_TXD
JP4.11
35
PA.3 / ADC_CH3 / PWM1_CH1 / UART3_RXD
JP4.12
36
PA.4 / ADC_CH4
JP6
JP6.1
37
PA.5 / ADC_CH5 / UART3_RXD
JP6.2
38
PA.6 / ADC_CH6 / UART3_TXD
JP6.3
39
PA.7 / ADC_CH7 / VREF
JP6.4
40
AVDD
JP6.5
41
PC.7 / I2C0_SCL / PWM0_BRAKE1
JP6.6
42
PC.6 / I2C0_SDA / PWM0_BRAKE0
JP6.7
43
PB.15 / INT1 / TM0_EXT / TM0
JP6.8
44
PF.0 / XT1_OUT
JP6.9
45
PF.1 / XT1_IN
JP6.10
46
nRESET
JP6.11
47
PF.8 / CLKO
JP6.12
48
PB.8 / STADC / TM0 / CLKO
Table 3-2 NUC1311LD2AE Full-pin Extension Connectors and GPIO Function List

NuMaker-NUC1311L
Aug. 12, 2022 Page 14 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
3.3.2 Arduino UNO Compatible Extension Connectors
Figure 3-4 shows the Arduino UNO compatible extension connectors.
Figure 3-4 Arduino UNO Compatible Extension Connectors

NuMaker-NUC1311L
Aug. 12, 2022 Page 15 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
Header
NuMaker-NUC1311L
Header
NuMaker-NUC1311L
Compatible to
Arduino UNO
GPIO Pin of
NUC1311LD2AE
Compatible to
Arduino UNO
GPIO Pin of
NUC1311LD2AE
NU3
NU3.1
RX
PB.4
NU2
NU2.6
SCL
PA.9
NU3.2
TX
PB.5
NU2.5
SDA
PA.8
NU3.3
D2
PA.12
NU2.4
A3
PA.3
NU3.4
D3
PA.13
NU2.3
A2
PA.2
NU3.5
D4
PA.14
NU2.2
A1
PA.1
NU3.6
D5
PA.15
NU2.1
A0
PA.0
NU3.7
D6
PA.10
NU1
NU1.8
VIN
-
NU3.8
D7
PA.11
NU1.7
VSS
NU4
NU4.1
D8
PF.4
NU1.6
VSS
NU4.2
D9
PF.5
NU1.5
5V
NU4.3
SS
PC.0
NU1.4
3V
NU4.4
MOSI
PC.3
NU1.3
RST
nRESET
NU4.5
MISO
PC.2
NU1.2
VDD
VDD
NU4.6
SCK
PC.1
NU1.1
NC
-
NU4.7
VSS
VSS
NU4.8
VREF
VREF
NU4.9
SDA
PA.8
NU4.10
SCL
PA.9
Table 3-3 Arduino UNO Extension Connectors and NUC1311LD2AE Mapping GPIO List

NuMaker-NUC1311L
Aug. 12, 2022 Page 16 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
3.4 Power Supply Configuration
The NuMaker-NUC1311L is able to adopt multiple power supplies. External power sources include NU1
Vin (7 V to 12 V), VDD (depending on the target chip operating voltage), and PC through USB connector.
By using switches and voltage regulator, multiple power domains can be created on the NuMaker-
NUC1311L.
3.4.1 VIN Power Source
Table 3-4 presents the Vin power source.
Connector
Net Name in
Schematic
Description
NU1 pin8
NU1_VIN
Board external power source, with voltage range from 7
V to 12 V. The voltage regulator UP2 converts the NU1
pin8 input voltage to 5 V and supplies it to NU1_5VCC.
Table 3-4 Vin Power Source
3.4.2 5 V Power Sources
Table 3-5 presents the 5 V power sources.
Connector
Net Name in
Schematic
Description
ICEJ3
USB_HS_VBUS
ICE USB connector supplies 5 V power from PC to
NUC1311 target board and Nu-Link2-Me.
J2
USB_VBUS
USB connector on NuMaker-NUC1311L supplies 5 V
power from PC to NUC1311 target board and Nu-Link2-
Me.
NU1 pin5
NU1_5VCC
ICEJ3, J2 or NU1 pin8 supplies 5 V power to NU1 pin5.
NU1 pin5 supplies 5 V power to target chip or Arduino
adapter board.
Note: NUC1311 operating voltage range is from 1.8 V
to 3.6 V. Do not switch SW2.1 (NU1 5VCC) to ON.
Table 3-5 5 V Power Sources

NuMaker-NUC1311L
Aug. 12, 2022 Page 17 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
3.4.3 3.3 V Power Sources
Table 3-6 presents the 3.3 V power sources.
Voltage
Regulator
5 V Source
Description
ICEUP1
USB_HS_VBUS
ICEUP1 converts USB_HS_VBUS to 3.3 V and
supplies 3.3 V to NUC1311 target board or ICE chip.
UP1
USB_VBUS
UP1 converts USB_VBUS to 3.3 V and supplies 3.3 V
to NUC1311 target board.
Note: SW2.2 (NU1 3VCC) should be switched to ON.
UP1
NU1_5VCC
UP1 converts NU1_5VCC to 3.3 V and supplies 3.3 V
to NUC1311 target board.
Note: SW2.2 (NU1 3VCC) should be switched to ON.
Table 3-6 3.3 V Power Sources
3.4.4 1.8 V Power Sources
Table 3-7 presents the 1.8 V power source.
Voltage Regular
5V Source
Description
ICEUP2
USB_HS_VBUS
ICEUP2 converts USB_HS_VBUS to 1.8 V and
supplies 1.8 V to NUC1311 target board or ICE chip.
Table 3-7 1.8 V Power Sources
3.4.5 Power Connectors
Table 3-8 presents the power connectors.
Connector
Description
JP1
VDD connector on the NuMaker-NUC1311L.
Note: NUC1311 operating voltage range is from 1.8 V to 3.6 V.
JP2
VSS connector on the NuMaker-NUC1311L.
Table 3-8 Power Connectors

NuMaker-NUC1311L
Aug. 12, 2022 Page 18 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
3.4.6 USB Connectors
Table 3-9 presents the USB connectors.
Connector
Description
ICEJ3
ICE USB connector on Nu-Link2-Me for power supply, debugging and
programming from PC.
J2
USB FS connector on NuMaker-NUC1311L for power supply.
Table 3-9 USB Connectors
3.4.7 Power Switches
Table 3-10 presents the power switches.
Switch
Description
ICEJPR1
Configures the target chip operating voltage at 1.8 V / 3.3 V / 5 V.
Note: NUC1311 operating voltage range is from 1.8 V to 3.6 V. Do not
switch ICEJPR1 (MCUVCC) to 5 V.
ICEJPR2
Configures the ICE chip operating voltage at 1.8 V / 3.3 V.
SW2
Configures the target chip operating voltage at 3.3 V / 5 V.
Note: NUC1311 operating voltage range is from 1.8 V to 3.6 V. Do not
switch SW2.1 (NU1 5VCC) to ON.
Table 3-10 Power Switches
3.4.8 Power Supply Models
External Power Supply through Nu-Link2-Me to Target Chip
The external power supply source on Nu-Link2-Me is shown in Figure 3-5.
Figure 3-5 External Power Supply Sources on Nu-Link2-Me

NuMaker-NUC1311L
Aug. 12, 2022 Page 19 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
To use ICEJ3 as external power supply source with Nu-Link2-Me, please follow the steps below:
1. Solder the resistor on ICEJPR1 (MCUVCC) depending on the target chip operating voltage.
2. Solder the resistor on ICEJPR2 (ICEVCC) depending on the ICE chip operating voltage.
3. Switch the SW2 to OFF.
4. Connect the external power supply to ICEJ3.
Table 3-11 presents all power models when supplying external power through Nu-Link2-Me. The Nu-
Link2-Me external power sources are highlighted in yellow.
Model
Target
Chip
Voltage
ICEJ3
ICEJPR1
(MCUVCC)
Selection [1]
ICEJPR2
(ICEVCC)
Selection [2]
ICE
Chip
Voltage
SW2
Selection
J2
Vin
JP1
1
1.8 V
Connect
to PC
1.8 V
1.8 V
1.8 V
Off
-
-
1.8 V
output
2
3.3 V
Connect
to PC
3.3 V (default)
3.3 V
(default)
3.3 V
Off
-
-
3.3 V
output
3
5 V
Connect
to PC
5 V
3.3 V
(default)
3.3 V
Off
-
-
5 V
output
Note:
1. 0 Ω should be soldered between ICEJPR1’s MCUVCC and 1.8 V / 3.3 V / 5 V.
2. 0 Ω should be soldered between ICEJPR2’s ICEVCC and 1.8 V / 3.3 V.
3. -: Unused.
Table 3-11 Supply External Power through Nu-Link2-Me
External Power Supply through NUC1311 Target Board to Target Chip
The external power supply sources on NUC1311 target board are shown in Figure 3-6.
Figure 3-6 External Power Supply Sources on NUC1311 Target Board
To use Vin or J2 as external power supply source, please follow the steps below:
1. Switch the SW2 depending on the target chip operating voltage.
2. Remove the resistor on ICEJPR1 (MCUVCC).
3. Solder the resistor on ICEJPR2 (ICEVCC) depending on the ICE chip operating voltage.
4. Connect the external power supply to Vin or J2.

NuMaker-NUC1311L
Aug. 12, 2022 Page 20 of 52 Rev 1.01
NUMAKER-NUC1311L USER MANUAL
Maker Nu-mbed NUC472 User Manual
To use JP1 as external power supply source, please follow the steps below:
Switch the SW2 to OFF.
2. Remove the resistor on ICEJPR1 (MCUVCC).
3. Solder the resistor on ICEJPR2 (ICEVCC) depending on the ICE chip operating voltage.
4. Connect ICEJ3 to PC.
5. Connect the external power supply to JP1.
To use Vin or J2 as external power supply source with Nu-Link2-Me detached from NuMaker-
NUC1311L, please follow the steps below:
Switch the SW2 depending on the target chip operating voltage.
2. Detach the Nu-Link2-Me from NuMaker-NUC1311L.
3. Connect the external power supply to Vin or J2.
To use JP1 as external power supply source with Nu-Link2-Me detached from NuMaker-
NUC1311L, please follow the steps below:
Switch the SW2 to OFF.
2. Detach the Nu-Link2-Me from NuMaker-NUC1311L.
3. Connect the external power supply to JP1.
Figure 3-7 Detach the Nu-Link2-Me from NuMaker-NUC1311L