NXP Semiconductors TWR-VF65GS10-PRO User manual

TOWER SYSTEM
Quick Start Guide
TWR-VF65GS10
For Vybrid Controller Solutions Based
on ARM®Cortex®-A5 and Cortex-M4
Processors with the DS-5 Toolchain
Downloaded from Arrow.com.

Quick Start Guide
Get to Know the TWR-VF65GS10
TWR-VF65GS10
Freescale Tower System
The TWR-VF65GS10 module is a part of the Freescale Tower System,
a modular development platform that enables rapid prototyping and
tool re-use through reconfigurable hardware. Elevate your design to
the next level and begin constructing your Tower System today.
Power/OpenSDA
Micro-USB
Reset
Dual USB
Accelerometer
LEDs
General-Purpose
TWRPI Plug-In
Vybrid JTAG
Header
38-pin Mictor
Trace Debug
External NPN
Ballast
Micro SD
Secondary
Connector
Primary Connector
K20 JTAG Header UART SelectionDual Quad SPI
Boot Config Reset Configuration
Line Drivers
Pushbuttons
DDR3
Front Side of
TWR-VF65GS10
Module
Downloaded from Arrow.com.Downloaded from Arrow.com.

TOWER SYSTEM
3
Get to Know the TWR-VF65GS10
K20
OpenSDA
Device
NAND Flash
Potentiometer
Back Side of
TWR-VF65GS10
Module
Battery
Receptacle
(VBAT)
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Quick Start Guide
4
TWR-VF65GS10 Features
• Vybrid MVF61NS151CMK50 controller (dual-core Cortex-A5
at 500 MHz + Cortex-M4 at 167 MHz, 1.5 MB SRAM, dual
Ethernet, dual USB, advanced security)
• Kinetis K20DX128VFM5 MCU-based OpenSDA circuit
• 1 Gb x 16 (128 MB) DDR3 in 96 FBGA package
• 2 Gb x 16 (256 MB) NAND flash
• Two 128 MB (16 MB) quad I/O serial flash
• Dual USB with on-chip PHY
• Interfaces to TWR-LCD-RGB graphical LCD module
• Four user-controlled status LEDs
• Three mechanical push buttons for user input and one for reset
• Potentiometer and three-axis digital accelerometer
• Micro SD card slot
• Independent battery-operated power supply for real-time clock
and tamper detection module
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TOWER SYSTEM
5
Step-by-Step Installation Instructions
This Quick Start Guide details how to set up the TWR-VF65GS10 module and run
some demo projects on the device.
2
Configure the
Hardware
• Assemble your Tower System
development platform per the
instructions found in the TWR-ELEV
module package, unless the board will
be used standalone.
• Insert the dual-headed USB-A side of
the provided USB cable into the PC
and insert the micro-B end into the
OpenSDA USB port (J3) on the
TWR-VF65GS10 module. Allow the
PC to automatically configure the
USB drivers if needed.
1
Download Software
and Tools
Download installation software
and documentation under
“Jump Start Your Design”
at freescale.com/TWR-VF65GS10.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Quick Start Guide
6
Step-by-Step Installation Instructions
Set up Serial
Communication
• A USB-to-serial bridge is supported
through the USB CDC functionality.
The serial port number is viewable
in the Device Manager (right click,
My Computer>Properties>Device
Manager>Port Settings). This allows
for serial communication between
the Tower module and a terminal
program running on the PC via the
USB connection.
• Setup a terminal program to use this
COM port with the following settings:
115200 baud, eight data bits, no
parity, one stop bit. Alternatively, you
may use the TWR-SER or TWR-SER2
serial module for serial communication.
See the “Introduction to the Vybrid
Tower System Module” video clip at
freescale.com/TWR-VF65GS10
for more details.
Locate and Install
CDC Device Drivers
• The module will enumerate as a
composite “Mass Storage and Serial
CDC Device.” The drivers for the
CDC functionality can be found
on the enumerated drive (for example:
F:\TWR-VF65GS).
• Go to that drive to find the CDC drivers
and install them.
43
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TOWER SYSTEM
7
Tilt the
Board
• After the TWR-VF65GS10 module
powers up, the U-Boot bootloader will
load the out-of-box demo from the
SD card. The Cortex-A5 core runs the
Linux
®
operating system and uses the
Open SDA USB-to-serial bridge. The
Cortex-M4 core runs the Freescale
MQX
™
RTOS and uses the TWR-
SER or TWR-SER2 serial module for
serial communication. Both operating
systems operate independently of each
other on their respective cores, but can
communicate via software APIs and
shared memory.
• Tilt the module to see different LEDs
light up—the accelerometer data is
being read by MQX on the M4 core
and transferred to Linux on the A5
core. You will also see Linux output
on the OpenSDA serial connection
set up in Step 3.
5
Explore the
Features
• Follow the “Introduction to the Vybrid
Tower System Module” video clip at
freescale.com/TWR-VF65GS10
to further explore the features and
capabilities of the out-of-box demo.
Start
Debugging
• To start debugging with DS-5,
the OpenSDA firmware needs to
be updated with the CMSIS-DAP
application. For more detail, please
refer to the “Jump Start Your
Design” documentation located at
freescale.com/TWR-VF65GS10
6
7
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Quick Start Guide
8
TWR-VF65GS10 Jumper Options
The following is a list of all jumper options on the TWR-VF65GS10. The default
settings are shown in bold.
Jumper Option Setting Description
J1
Vybrid VBAT power
source - SecureRTC,
32 kHz XOSC,
Tamper, and Monitors
1-2 VBAT tied to main Vybrid 3.3 V (VCC_3V3_MCU)
2-3 VBAT tied to Coin Cell
J4
VCC_3V3_MCU -
main Vybrid 3.3 V
supply (VDD33 pins)
ON P3V3 from on-board 3.3 V regulator tied directly
to VCC_3V3_MCU
OFF Current-measuring device installed instead of jumper
J6 JTAG 5 V supply
OFF Pin 11 & 13 of JTAG connector floating
ON Pin 11 & 13 of JTAG connecter tied to 5 V
J7 Tamper loopback
ON EXT_WM0_TAMPER_IN tied to
EXT_WM0_TAMPER_OUT
OFF EXT_WM0_TAMPER_IN open;
EXT_WM0_TAMPER_OUT open
J13 Accelerometer
interrupt
ON MCU PTB9 pin tied to INT1 of accelerometer
OFF Accelerometer Interrupt input untied
J18
3.3 V from Vybrid
board to Tower
system (applicable
only when Elevator
not powered with 5 V)
ON P3V3 tied to P3V3_ELEV
OFF Board and Tower System 3.3 V power rails untied
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TOWER SYSTEM
9
(continued from previous page)
Jumper Option Setting Description
J19 Onboard 5 V source
1-2 P5V comes from USB Micro-B connector J3
(only option when “OpenSDA” operates)
2-3 P5V comes from Peripheral USB OTG Micro-B J8
J20 Power source for
Vybrid USB0 PHY
1-2 Self-powered - USB0_VBUS tied to P5V
2-3 Bus-powered - USB0_VBUS tied to VBUS of Peripheral
USB OTG Micro-B J8
J21 Power source for
Vybrid USB1 PHY
ON USB1_VBUS tied to VBUS of Host USB Type-A J12
OFF USB1 PHY unpowered
J22
Pins 1
to 10
Boot configuration
ON/INSTALLED-1,
OFF-0
12345
246 8 10
13579
12_345 Switch Settings Detail
10_000 QuadSPI Boot
10_110 SD Card Boot
10_001 NAND Boot
01_xxx UART/USB Boot
00_xxx Boot From Fuses
J23 SCI1_TX and
SCI2_TX select
1-2 SCI1_TX connected to ELEV_UART1_TX
1-3 SCI1_TX connected to OpenSDA_UART_RX
2-4 SCI2_TX connected to ELEV_UART1_TX
3-4 SCI2_TX connected to OpenSDA_UART_RX
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Quick Start Guide
10
TWR-VF65GS10 Jumper Settings
(continued from previous page)
Jumper Option Setting Description
J23
continued
SCI1_RX and
SCI2_RX select
7-8 SCI1_RX connected to ELEV_UART1_RX
7-9 SCI1_RX connected to OpenSDA_UART_TX
8-10 SCI2_RX connected to ELEV_UART1_RX
9-10 SCI2_RX connected to OpenSDA_UART_TX
J25 Elevator 5 V supply
ON P5V tied to P5V_ELEV
OFF Board and Tower System 5 V power rails untied
R164,
R165
USB0 multiplexer
selection
AConnected to Peripheral USB OTG Micro-B
connector J8
BConnected to Tower System elevator
R21 Optional Ethernet MII
interface
ARMII CLK
BMII0 TXCLK
R175 to
R181
Optional Ethernet MII
interface
None RMII Interfaces used
0-Ohm MII0 Interface used
R182 Optional Ethernet MII
interface
ASAI RX BCLK
BMII0 RXCLK
SH10 Vybrid SDRAM
controller power
Shorted Power pins tied directly to onboard 1.5 V source
Cut Current measuring device connected across
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.