OEM Tools 24987 Service manual

UNPACKING
After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for loose,
missing, or damaged parts. If any damage is observed, a shipping damage claim must be filed with the carrier. DO
NOT use the OEMTOOLS®Sidekick Creeper Stool if broken, bent, cracked or damaged parts (including labels)
are noted. Any Rolling Stool that appears damaged in any way, operates abnormally or is missing parts should be
removed from service immediately. If you suspect that the Rolling Stool was subjected to shock load (a load that was
dropped suddenly, unexpectedly, etc.), immediately discontinue use until it has been checked by a factory authorized
service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and
others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal
injury and/or damage to product or property. Please retain instructions for future reference.
Operating Instructions and Parts Manual 24987
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
Thank you very much for choosing an OEMTOOLS®Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible for issues
arising from modification. We strongly recommend that this product is not modified and/or used for any application other than that
for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first
contacted customer service to determine if it can or should be performed on the product.
WARNING:This product can expose you to chemicals, including DEHP and lead, which are known to the State of
California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
SIDEKICK CREEPER STOOL
1
7/21
2021 OEMTOOLS®

2
Operating Instructions and Parts Manual 24987
7/21
2021 OEMTOOLS™
SIDEKICK CREEPER STOOL
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your product. Read this manual carefully. Learn
the product’s applications and limitations, as well as
potential hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
3. Keep children away. All children should be kept away
from the work area. Never let a child handle tools or
equipment without strict adult supervision.
4. DO NOT operate this product if under the influence of
alcohol or drugs. Read warning labels on prescriptions
to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, DO NOT
attempt to operate.
5. Use safety equipment. Eye protection should be worn at all
times when operating this tool. Use ANSI approved safety
glasses. Everyday eyeglasses are NOT safety glasses. Dust
mask, non-skid safety shoes, hard hat or hearing protection
should be used in appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties,
rings, bracelets or other jewelry may present a potential
hazard when operating this product. Keep all apparel
clear of the product.
7. DO NOT overreach. Keep proper footing and balance
at all times when operating this product.
8. Check for damage. Check equipment regularly. If part of
the product is damaged, it should be carefully inspected
to make sure that it can perform its intended function
correctly. If in doubt, discontinue use of product.
9. Keep away from flammables. DO NOT attempt to operate
this product near flammable materials or combustibles.
Failure to comply may cause serious injury or death.
10. Store this product out of the reach of children and
untrained persons. This product may be dangerous in
the hands of untrained users.
11. Keep this product dry and clean.
12. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one product may become hazardous when
used on another product.
13. Service must be performed only by qualified repair
personnel. Service or maintenance performed by
unqualified personnel could result in a risk of injury.
14. When servicing a product, use only identical replacement
parts. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.
15. Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. DO NOT use this
product in a damp or wet location.
16. Maintain labels and nameplates on this product. These
carry important information. If unreadable or missing,
contact OEMTOOLS®for a replacement.
17. Keep this product dry, clean, and free from brake fluid,
oil, and grease.
18. Avoid accidental fire. DO NOT smoke near this product.
19. The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are factors
which cannot be built into this product, but must be
supplied by the operator.
20. We believe the information contained herein to be
reliable. However, general technical information is given
by us without charge and the user shall employ such
information at their own discretion and risk. We assume
no responsibility for results or damages incurred from
the use of such information in whole or in part.
21. The manufacturer declines any and all responsibility
for property damage or injury if said damage is the
result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
22. The procedures documented in this manual are to
serve as guidelines for the use of this equipment.
23. The use of this equipment is simple and straightforward
if you follow the instructions. When operating this
equipment, use common sense, and only use this
equipment for its intended purpose.
PRODUCT DESCRIPTION
The OEMTOOLS®24987 Sidekick Creeper Stool is designed for easy
access to tools and supplies. Large open trays allow user to carry a
wide range of items with additional holster caddies on the side for
rapid access to the user’s items. The slide out under seat drawer can
be used to store and organize smaller items.
PRODUCT SPECIFICATIONS
Length 17.72"
Width 14.96"
Height 14.96"
Weight 20.9 Lb.
Weight Capacity 300 Lb.
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
1. DO NOT place under automobile tires to move or
reposition vehicle.
2. DO NOT use as a toy or skateboard.
3. DO NOT stand on unit or use as a stepping device.
4. DO NOT use if one or more wheels are inoperative.
Repair before re-use.
5. DO NOT use if any part of the support structure is
broken, split or cracked.
6. When not in use, unit should be stored in a secure
place.
7. Always store in an upright position.
8. Keep out of the reach of children.
ASSEMBLY
1. Put the screw (#7) go through the hole of the caster (#5)
then go through the hole of plastic body (#1).
2. Put the sleeve (#6) through the screw (#7).
3. Settle the caster with flat washer (#4) and nut M6 (#3).

3
Operating Instructions and Parts Manual 24987
7/21
2021 OEMTOOLS™
SIDEKICK CREEPER STOOL
Figure Description Qty.
1
Seat Cover 1
2Seat Creeper Frame 1
3, 4, 6, 7 Removable Trays 5
5Nuts 4
8Wheels 4
NOTE:Not all components of the Sidekick Creeper Stool are replacement items, but are illustrated as a convenient reference for location and
position in the assembly sequence. The manufacturer and/or distributor have provided the parts list and assembly diagram in this manual as
a reference tool only. Neither the manufacturer nor distributor makes any representation or warranty of any kind to the buyer that he or she is
qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or
distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the
buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out
of his or her installation of replacement parts thereto.

4
Operating Instructions and Parts Manual 24987
7/21
2021 OEMTOOLS™
SIDEKICK CREEPER STOOL
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
CONTACT US
OEMTOOLS®ONE YEAR WARRANTY
For up to one year from the date of purchase of this OEMTOOLS®product, if you find any defect in material or workmanship (through normal usage),
return it to the place of purchase or to OEMTOOLS®for repair or replacement at our discretion. In order to obtain this service, send the product and
proof of purchase (transportation pre-paid) to:
OEMTOOLS®Q.A. Dept, 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our inspection verifies the defect, we will
either repair or replace the product, or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We
will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our
warranty, then you must bear the cost of returning the product.
OEMTOOLS®does not provide warranty for products labeled other than OEM®or OEMTOOLS®. OEMTOOLS®will not provide any warranty for products
subjected to abnormal use. Abnormal use includes (but is not limited to) abuse, accident, alteration, neglect, and unauthorized or unreasonable use or
repairs. This warranty does not cover bits, blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace
blades, bits, files, and batteries as necessary. OEMTOOLS®reserves the right to make any changes in construction or design at any time without any
obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS®makes every effort to ensure that its products meet high quality and durability standards, and warrants to the original purchaser that
this product is free from defects in materials and workmanship for the period of one year from the date of purchase. This warranty does not apply
to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the
use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Don’t forget to register your new OEMTOOLS®product at www.oem-tools.com.