OHAUS EX124 User manual

Explorer®Balances
Instruction Manual

EXPLORER BALANCES EN-1
TABLE OF CONTENTS
1. INTRODUCTION ....................................................................................................................5
1.1 Description ................................................................................................................................................... 5
1.2 Features ....................................................................................................................................................... 5
1.3 Safety Precautions ....................................................................................................................................... 5
2. INSTALLATION .....................................................................................................................6
2.1 Unpacking .................................................................................................................................................... 6
2.2 Installing Components.................................................................................................................................. 7
2.2.1 Terminal Setup ......................................................................................................................................... 7
2.2.2 Installing the Wind Ring, Weighing Platform on Models EX124, EX224, and EX324 ............................. 7
2.2.4 Installing the Draft Shield Glass and Doors on Draft Shield Models........................................................ 8
2.2.5 Installing the Weighing Pan & Wind Shield – Non-Draft Shield Models .................................................. 9
2.3 Selecting the Location.................................................................................................................................. 9
2.4 Leveling the Equipment................................................................................................................................ 9
2.5 Connecting Power...................................................................................................................................... 10
2.5.1 AC Adapter............................................................................................................................................. 10
2.6 Connecting the Interface ............................................................................................................................ 10
2.7 Adjusting the View Angle of the Terminal .................................................................................................. 10
2.8 Remote Terminal Operation................................................................................................................... 11
2.8.1 Separating the Terminal from the Weighing Base ................................................................................. 11
2.8.2 Terminal Mounting.................................................................................................................................. 11
2.9 Initial Calibration......................................................................................................................................... 11
3. OPERATION ........................................................................................................................12
3.1 Overview of Display, Home Screen ........................................................................................................... 12
3.2 Principal Functions and Main Menu.......................................................................................................... 12
3.3 Overview of Parts and Features –Draft Shield Models.............................................................................. 13
3.4 Overview of Parts and Features – Non-Draft Shield Models ..................................................................... 14
3.5 Overview of Parts and Features – Terminal .............................................................................................. 15
3.6 Functions and Their Icons.......................................................................................................................... 16
3.6.1 Standby .................................................................................................................................................. 16
3.6.2 Printing Data........................................................................................................................................... 16
3.6.3 Applications ............................................................................................................................................ 16
3.6.4 TouchLess Sensor Status ...................................................................................................................... 16
3.6.5 AutoCal™................................................................................................................................................ 16
3.6.6 Menu ...................................................................................................................................................... 16
3.6.7 More….................................................................................................................................................... 16
3.6.8 Level Assist ............................................................................................................................................ 16
3.6.9 Zero Operation ....................................................................................................................................... 16
3.6.10 Taring a Container.................................................................................................................................. 16
3.6.11 Weighing Units ....................................................................................................................................... 17
3.6.12 Preset Tare............................................................................................................................................. 17
3.6.13 Calibration Test ...................................................................................................................................... 17
3.6.14 Calculator ............................................................................................................................................... 17
3.6.15 Stopwatch............................................................................................................................................... 17
3.6.16 Logout .................................................................................................................................................... 17
4. APPLICATIONS ...................................................................................................................18
4.1 Weighing .................................................................................................................................................... 19
4.1.1 Edit Settings ........................................................................................................................................... 19
4.1.2 Application Setup ................................................................................................................................... 20
4.1.3 Statistics for Weighing............................................................................................................................ 21
4.2 Parts Counting ........................................................................................................................................... 22
4.2.1 Standard Parts Counting (default).......................................................................................................... 22
4.2.2 Application Setup ................................................................................................................................... 25
4.2.3 Parts Counting – Check ......................................................................................................................... 26
4.2.4 Parts Counting – Fill............................................................................................................................... 27
4.2.5 Statistics for Parts Counting................................................................................................................... 28
4.3 Percent Weighing....................................................................................................................................... 30
4.3.1 Edit Settings ........................................................................................................................................... 30
4.3.2 Application Setup ................................................................................................................................... 33
4.4 Check Weighing ......................................................................................................................................... 34

EN-2 EXPLORER BALANCES
4.4.1 Standard Check Weighing (default) ....................................................................................................... 34
4.4.2 Edit Settings ........................................................................................................................................... 34
4.4.3 Application Setup ................................................................................................................................... 35
4.4.4 Check Weighing – Nominal/Weight Mode ............................................................................................. 36
4.4.5 Check Weighing – Nominal/Percent Tolerance Mode ........................................................................... 37
4.4.6 Display Settings...................................................................................................................................... 38
4.4.7 Statistics for Check Weighing ................................................................................................................ 39
4.5 Dynamic/Animal Weighing ......................................................................................................................... 40
4.5.1 Edit Settings ........................................................................................................................................... 41
4.5.2 Application Setup ................................................................................................................................... 41
4.5.3 Dynamic Weighing – Semi-Auto ............................................................................................................ 42
4.5.4 Dynamic Weighing – Automatic ............................................................................................................. 43
4.5.5 Statistics for Dynamic Weighing............................................................................................................. 44
4.6 Filling .......................................................................................................................................................... 45
4.6.1 Edit Settings ........................................................................................................................................... 45
4.6.2 Application Setup ................................................................................................................................... 46
4.6.3 Statistics for Filling ................................................................................................................................. 47
4.7 Totalization................................................................................................................................................. 49
4.7.1 Totalization – Manual (Default) .............................................................................................................. 49
4.7.2 Application Setup ................................................................................................................................... 50
4.7.3 Totalization – Automatic......................................................................................................................... 51
4.8 Formulation ................................................................................................................................................ 52
4.8.1 Free Formulation (default)...................................................................................................................... 52
4.8.2 Application Setup ................................................................................................................................... 53
4.8.3 Recipe Formulation ................................................................................................................................ 54
4.9 Differential Weighing .................................................................................................................................. 57
4.9.1 Item Settings .......................................................................................................................................... 57
4.9.2 Application Setup ................................................................................................................................... 59
4.9.3 Differential Weighing with Auto-Process On .......................................................................................... 60
4.10 Density Determination................................................................................................................................ 61
4.10.1 Measuring the Density of a Solid Using Water (default) ........................................................................ 61
4.10.2 Application Setup ................................................................................................................................... 63
4.10.3 Measuring the Density of a Buoyant Material Using Water ................................................................... 64
4.10.4 Measuring the Density of a Solid Using an Auxiliary Liquid................................................................... 64
4.10.5 Measuring the Density of a liquid using a Calibrated Sinker (not supplied)........................................... 65
4.10.6 Measuring the Density of Porous Material Using Oil ............................................................................. 67
4.11 Peak Hold................................................................................................................................................... 69
4.11.1 Peak Hold – Semi-Automatic (default) ................................................................................................... 69
4.11.2 Application Setup ................................................................................................................................... 70
4.11.3 Peak Hold – Manual............................................................................................................................... 71
4.11.4 Peak Hold – Automatic........................................................................................................................... 72
4.12 Ingredient Costing ...................................................................................................................................... 73
4.12.1 Item Settings .......................................................................................................................................... 73
4.12.2 Application Setup ................................................................................................................................... 76
4.13 Pipette Adjustment ..................................................................................................................................... 77
4.13.1 Pipette Adjustment – Manual (default)................................................................................................... 77
4.13.2 Begin Pipette Adjustment Process......................................................................................................... 79
4.13.3 Application Setup ................................................................................................................................... 80
4.14 Statistical Quality Control (SQC)................................................................................................................ 81
4.14.1 Edit Settings ........................................................................................................................................... 81
4.14.2 Begin the SQC Process ......................................................................................................................... 82
4.14.3 Application Setup ................................................................................................................................... 84
4.15 Statistics ..................................................................................................................................................... 85
4.16 Library ........................................................................................................................................................ 85
4.16.1 Creating a Library Record ...................................................................................................................... 85
4.16.2 Retrieving a Library Record ................................................................................................................... 86
4.16.3 Deleting a Stored Library Record........................................................................................................... 86
4.17 Additional Features .................................................................................................................................... 87
4.17.1 Weigh Below .......................................................................................................................................... 87
5. MENU SETTINGS ................................................................................................................88
5.1 Menu Navigation ........................................................................................................................................ 88
5.1.1 Changing Settings.................................................................................................................................. 88
5.2 Main Menu.................................................................................................................................................. 89

EXPLORER BALANCES EN-3
5.3 Calibration .................................................................................................................................................. 89
5.3.1 Calibration sub-menu ............................................................................................................................. 89
5.3.2 Internal Calibration (AutoCal™) ............................................................................................................. 89
5.3.3 Automatic Calibration ............................................................................................................................. 89
5.3.4 AutoCal™ Adjustment............................................................................................................................ 90
5.3.5 Span Calibration..................................................................................................................................... 90
5.3.6 User Calibration...................................................................................................................................... 91
5.3.7 Calibration Test ...................................................................................................................................... 91
5.4 User Settings.............................................................................................................................................. 92
5.4.1 User Settings Sub-menu ........................................................................................................................ 92
5.4.2 Language ............................................................................................................................................... 92
5.4.3 Volume ................................................................................................................................................... 92
5.4.4 Display Settings...................................................................................................................................... 92
5.4.5 User Manager......................................................................................................................................... 92
5.4.6 Functions Configuration ......................................................................................................................... 93
5.4.7 TouchLess Sensor Setup....................................................................................................................... 93
5.4.8 Draft Shield light ..................................................................................................................................... 93
5.5 Balance Setup............................................................................................................................................ 94
5.5.1 Balance Set-up sub-menu...................................................................................................................... 94
5.5.2 Stable Range.......................................................................................................................................... 94
5.5.3 Filter level ............................................................................................................................................... 94
5.5.4 Auto Zero Tracking................................................................................................................................. 94
5.5.5 Auto Tare................................................................................................................................................ 95
5.5.6 Gross Indicator ....................................................................................................................................... 95
5.5.7 Legal For Trade...................................................................................................................................... 95
5.5.8 Graduations............................................................................................................................................ 95
5.5.9 Date & Time ........................................................................................................................................... 95
5.6 Applications................................................................................................................................................ 96
5.6.1 Turning an Application ON/OFF............................................................................................................. 96
5.7 Weighing Units ........................................................................................................................................... 96
5.7.1 Units Sub-menu...................................................................................................................................... 96
5.7.2 Turning a Unit ON/OFF .......................................................................................................................... 97
5.7.3 Custom Units.......................................................................................................................................... 97
5.8 GLP and GMP Data ................................................................................................................................... 98
5.8.1 GLP Data Sub-menu.............................................................................................................................. 98
5.8.2 Header.................................................................................................................................................... 98
5.8.3 Balance Name........................................................................................................................................ 98
5.8.4 User Name ............................................................................................................................................. 98
5.8.5 Project Name.......................................................................................................................................... 98
5.9 Communication .......................................................................................................................................... 99
5.9.1 Communication Sub-menu..................................................................................................................... 99
5.9.2 Baud Rate .............................................................................................................................................. 99
5.9.3 Transmission .......................................................................................................................................... 99
5.9.4 Handshake ........................................................................................................................................... 100
5.9.5 Alternate Command ............................................................................................................................. 100
5.9.6 Print Output .......................................................................................................................................... 100
5.9.7 Auto Print.............................................................................................................................................. 101
5.9.8 Print Calibration Data ........................................................................................................................... 101
5.9.9 Print Content ........................................................................................................................................ 101
5.9.10 Print Layout .......................................................................................................................................... 103
5.9.11 Data Transfer Function ........................................................................................................................ 103
Double click “Accessibility Options” in control panel......................................................................................... 104
5.10 Library ...................................................................................................................................................... 105
5.11 I/O Settings............................................................................................................................................... 105
5.12 Diagnostics............................................................................................................................................... 105
5.12.1 Level Bubble Light................................................................................................................................ 105
5.12.2 Draft Shield Light (Analytical models) .................................................................................................. 105
5.12.3 Sensors ................................................................................................................................................ 105
5.12.4 Service Menu ....................................................................................................................................... 105
5.13 Factory Reset........................................................................................................................................... 106
5.13.1 Factory Reset Sub-menu ..................................................................................................................... 106
5.13.2 Reset Calibration.................................................................................................................................. 106
5.13.3 Reset User Settings ............................................................................................................................. 106

EN-4 EXPLORER BALANCES
5.13.4 Reset Balance Setup............................................................................................................................ 106
5.13.5 Reset Application Modes ..................................................................................................................... 106
5.13.6 Reset Weighing Units........................................................................................................................... 106
5.13.7 Reset GLP and GMP Data................................................................................................................... 106
5.13.8 Reset Communication.......................................................................................................................... 106
5.13.9 Reset I/O Settings ................................................................................................................................ 106
5.13.10 Reset All (Global Reset)....................................................................................................................... 106
5.14 Lockout..................................................................................................................................................... 107
5.14.1 Lockout Sub-menu ............................................................................................................................... 107
5.14.2 Lock Calibration.................................................................................................................................... 107
5.14.3 Lock User Settings ............................................................................................................................... 107
5.14.4 Lock Balance Setup ............................................................................................................................. 107
5.14.5 Lock Application Modes ....................................................................................................................... 107
5.14.6 Lock Weighing Units............................................................................................................................. 107
5.14.7 Lock GLP and GMP Data..................................................................................................................... 107
5.14.8 Lock Communication............................................................................................................................ 108
5.14.9 Lock Library.......................................................................................................................................... 108
5.14.10 Lock I/O Settings .................................................................................................................................. 108
5.14.11 Factory Reset ....................................................................................................................................... 108
5.15 Securing the Menu and Key Lock menu settings..................................................................................... 108
5.16 Information ............................................................................................................................................... 109
5.16.1 Using Information ................................................................................................................................. 109
6. LEGAL FOR TRADE..........................................................................................................110
6.1 Settings .................................................................................................................................................... 110
6.2 Verification................................................................................................................................................ 110
6.3 Sealing ..................................................................................................................................................... 110
7. PRINTING ..........................................................................................................................111
7.1 Connecting, Configuring and Testing the Printer/Computer Interface..................................................... 111
7.2 Printout Examples .................................................................................................................................... 112
7.3 Output Format .......................................................................................................................................... 120
8. MAINTENANCE .................................................................................................................121
8.1 Calibration ................................................................................................................................................ 121
8.2 Cleaning ................................................................................................................................................... 121
8.3 Troubleshooting ....................................................................................................................................... 121
8.4 Service Information .................................................................................................................................. 121
9. TECHNICAL DATA ............................................................................................................122
9.1 Specifications ........................................................................................................................................... 122
9.2 Drawings and Dimensions ....................................................................................................................... 129
9.3 Parts and Accessories ............................................................................................................................. 130
9.4 Icons List .................................................................................................................................................. 131
9.5 Communication ........................................................................................................................................ 137
9.5.1 Interface Commands............................................................................................................................ 137
9.5.2 RS232 (DB9) Pin Connections............................................................................................................. 140
9.6 The USB Interface.................................................................................................................................... 140
10.SOFTWARE UPDATES .....................................................................................................144
11.COMPLIANCE....................................................................................................................145

EXPLORER BALANCES EN-5
1. INTRODUCTION
1.1 Description
The Explorer balance is a precision weighing instrument that will provide you with years of service if properly cared
for. The Ohaus Explorer balances are available in capacities from 120 grams to 10,200 grams.
1.2 Features
Modular Design: Ohaus Explorer balances are composed of two interconnected modules: a Terminal and a Base.
Depending on the user’s needs, the unit can be operated with the Terminal either attached to, or remote from, the
Base, with a single interconnect cord 1 meter long.
Touch Controls: Quick, graphical access to all control
functions, over a dozen applications and many features.
Touchless Sensors: can be assigned functions when
activated: Zero, Print, Tare, etc.
Statistics: available in Weighing, Counting, Percent
Weighing, Check Weighing, Dynamic Weighing, Filling,
Density Determination, Pipette Adjustment and
Statistical Quality Control applications.
1.3 Safety Precautions
Caution: Read all safety warnings before installing, making connections, or servicing this
equipment. Failure to comply with these warnings could result in personal injury and/or
property damage. Retain all instructions for future reference.
•Verify that the input voltage range printed on the data label and the plug type matches the local AC power
to be used.
•Make sure that the power cord does not pose a potential obstacle or tripping hazard.
•Use the balance only in dry locations.
•Do not drop loads on the pan.
•Use only approved accessories and peripherals.
•Operate the equipment only under ambient conditions specified in these instructions.
•Disconnect the equipment from the power supply when cleaning.
•Do not operate the equipment in hazardous or unstable environments.
•Service should only be performed by authorized personnel.

EN-6 EXPLORER BALANCES
2. INSTALLATION
2.1 Unpacking
Carefully remove your Explorer balance and each of its components from the package. The included components
vary depending on the balance model (see table below). Save the packaging to ensure safe storage and transport.
Included Component Photo
EX124
EX224
EX324
EX223
EX423
EX623
EX1103
EX2202
EX4202
EX6201
EX6202
EX10201
EX10202
Terminal X X X
Weighing Base X X X
Weighing Platform 90 mm Diameter
X
130 mm Diameter
X
180 x 210 mm
X
Sub-Platform 130mm Diameter
X
Support Caps
(4 Pcs)
X
Wind Ring X
Wind Shield
X
Draft Shield
Assembly X X
Power Adapter X X X
Power Cord (Country specific) X X X
Use Cover Terminal X X X
Compact Disk: USB Software X X X
Instruction Manual X X X
Quick Start Guide X X X
Warranty Card X X X

EXPLORER BALANCES EN-7
2.2 Installing Components
Refer to the illustrations and instructions below to identify and assemble your Explorer balance with its
components. All components must be assembled before using the balance.
2.2.1 Terminal Setup
When the Explorer is delivered, the Terminal is already attached (docked) to the Base. No additional setup is
necessary. However, for Draft Shield models, the Terminal needs to be detached temporarily in order to assemble
parts of the Draft Shield. Refer to the illustrations and instructions below to identify and assemble your Explorer
Balance.
Note: The Terminal is identical for all Explorer Balance models.
2.2.2 Installing the Wind Ring, Weighing Platform on Models EX124, EX224, and EX324
Note: Assembly instructions also apply to models with the suffix M or N.
1. Place the Wind Ring in position.
2. Insert the Platform Assembly
onto the Mounting Cone located
in the center of the Balance.
2.2.3 Installing the Sub-Platform and Weighing Pan on Models EX223, EX423, EX623 and EX1103
1. Place the Sub-platform in
position.
2. Position the Platform on the
Sub-platform.

EN-8 EXPLORER BALANCES
2.2.4 Installing the Draft Shield Glass and Doors on Draft Shield Models
1. Carefully remove each of the four glass Draft Shield sections from the packaging.
NOTE: Before installing side doors, be sure to set the lock tabs in the proper position, as shown here.
UNLOCK:
LOCK:
2. Follow the steps below to install side, front and top doors of the Draft Shield.
Side Door Installation
1. Unlock 2. Align
3. Clear 4. Lock
Position glass door to slide. Open lock tab (top); insert in top groove and slide inside bottom groove. Close lock tab.
Front Panel Installation
1. Release
terminal
2. Align
3. Push to
rear
4. Reconnect
terminal
Press button to separate Terminal from Base. Seat panel’s hooked ends in base. Swing panel to vertical position.
Top Door Installation
1. Align 2. Press Down
Insert Top Door’s hooked ends in grooved pegs. Press gently to seat. Check for smooth movement. Close door.

EXPLORER BALANCES EN-9
2.2.5 Installing the Weighing Pan & Wind Shield – Non-Draft Shield Models
Note: Assembly instructions also apply to models with the suffix M or N.
1. Place the four Support Caps onto the Balance as shown.
2. Place the Weighing Pan on the Support Caps
3. Place the Wind Shield onto the Balance as shown.
Note: The balance can be operated without the Wind Shield. However, depending on ambient conditions the
displayed results may be slightly less stable.
2.3 Selecting the Location
Avoid excessive vibrations, heat sources, air current, or rapid temperature changes. Allow sufficient space.
Note: Interface cables connect to the terminal. The terminal can be detached and mounted on a wall or
positioned on a table separate from the balance.
2.4 Leveling the Equipment
The Explorer has an illuminated level indicator as a reminder that the balance should
be leveled for accurate weighing. There is a level bubble in a small round window on
the front of the Base. To level the balance, adjust the Leveling Thumbwheels at each
corner until the bubble is centered in the circle.
Be sure the equipment is level each time its location is changed.
Note: The feet cannot rotate. The Thumbwheels must be used for leveling.
See the Level Assist screen in the Information Menu.
To see the Level Assist menu, touch
More on the bottom-right corner of the
main screen. Then touch Level Assist.
The Level Assist screen shows which
direction to turn the thumbwheels to
center the level bubble.

EN-10 EXPLORER BALANCES
2.5 Connecting Power
2.5.1 AC Adapter
Connect the power cord of the AC Adapter (supplied) to the power receptacle on the rear of the Base.
Then connect the AC adapter plug to a suitable electrical outlet.
Caution: For use with CSA certified (or equivalent approved) power source,
which must have a limited current output.
Note: Allow equipment to warm up for 60 minutes for optimal weighing performance.
Standby: When unit is plugged in, it starts in Standby mode. Press the Standby icon to start.
2.6 Connecting the Interface
Use the built-in RS-232 (10101) Port to connect either to a
computer or a printer with a standard (straight-through) serial
cable. Or connect using the scale’s USB port.
Note: For configuration and interface commands, see the
Communication Menu Settings section.
For Connecting, Configuring and Testing the Printer/Computer
Interface, and for sample Print Output Formats, see the Printing
section.
Interface connections on back of Terminal.
Thread printer cable along cable coils on bottom of balance. Or pass cable through groove near release button.
2.7 Adjusting the View Angle of the Terminal
To adjust the Terminal display’s viewing angle, press in the Terminal Adjust buttons on both sides of the Terminal.

EXPLORER BALANCES EN-11
2.8 Remote Terminal Operation
The Terminal communicates with the weighing base via the Terminal cable. This cable must be plugged into the
Terminal for the Explorer to display properly. If desired, the Explorer balance may be operated either with the
Terminal attached (as-shipped), or remotely (up to 1 meter away).
2.8.1 Separating the Terminal from the Weighing Base
1. To detach, press both the Release buttons inward (both at the same time) and gently pull the Terminal
towards you (outward) until the Terminal is detached. These Release buttons disengage the two hooks
holding the Terminal to the Base. A cable is attached to the Terminal. Take care to not damage or
disconnect this cable.
2. To reattach the Terminal, press in the two Release buttons and slide the Terminal into the Base until the
Terminal hooks click and engage to hold the Terminal in place.
Release Button Base and Terminal Terminal Cable
Note: If a longer operation distance is required, a Terminal Extension cable is available as an accessory.
2.8.2 Terminal Mounting
If desired, the Terminal may be mounted to a wall or table using fasteners (not supplied) that are appropriate for the
type of mounting surface The Terminal bracket will accommodate 4mm (#8) screws. Locate the mounting holes as
shown in Figure 2-1.
Figure 2-1. Terminal Mounting Dimensions.
2.9 Initial Calibration
When the Balance is first installed, and when it is moved to another location, it must be calibrated to ensure
accurate weighing results. The Explorer Balances have built in AutoCal which can calibrate the balance
automatically and does not require calibration masses. If preferred, the balance can be manually calibrated with
external masses. Have the appropriate calibration masses available before beginning calibration. Refer to the
Calibration Section for masses and calibration procedure.
56.5 mm
2.2 in
112 mm / 4.4 in
48.5 mm
1.9 in

EN-12 EXPLORER BALANCES
3. OPERATION
3.1 Overview of Display, Home Screen
This equipment utilizes a touch-sensitive display. Touch areas and Buttons to control the equipment’s functions.
CONTROLS Touch to access application setup menu
Touch to change
applications Touch to access available libraries
Touch for information menu
Instructional Messages
Stability (*), Net (NET),
Gross (G) and/or center
of zero (>0<) indicators
Touch unit indicator to
change weighing unit
Capacity or Status Guides:
Vary by application
Result Fields:
Information varies by
application
Application Buttons:
Functions vary by
application
Touch icons to perform
specific functions or
access other functions
3.2 Principal Functions and Main Menu
Weighing: Press Tare to set the display to zero. Place an item on the pan. Display indicates gross weight.
Taring: With no load on the pan, press Tare to set the display to zero. Place an empty container on the pan
and press Tare. Add material to the container and its net weight is displayed. Remove container and
container’s weight appears as a negative number. Press Tare to clear.
MENU & SCREEN NAVIGATION
Touch Menu to open the menu list.
Touch and drag the Scroll bar to view additional items.
Calibration:
Touch to view calibration options.
User Settings:
Touch to view user preferences.
Balance Setup:
Touch to view balance settings.
Application Modes:
Touch to view application modes.
Weighing Units:
Touch to view weighing units.
GLP and GMP Data:
Insert user data for traceability.
Diagnostics:
Touch to view Diagnostics items.
Communication:
Touch to view COM Device Settings and Print
Settings.
Factory Reset:
Touch to do a Factory reset.
Library:
Touch to delete all Library records.
Lockout:
Touch to access the Lockout menu list.
I/O Settings:
Touch to view remote I/O Settings.
Information:
Touch to view list of topics.

EXPLORER BALANCES EN-13
3.3 Overview of Parts and Features –Draft Shield Models
Top View
Rear View
Bottom View
Side View
Figure 3-1. Explorer Balance (models EX124, EX224, EX324, EX223, EX423, EX623, EX1103)
Leveling
Thumbwheels
Data label
Terminal cable
storage clips
Lock switch Weigh
Below
Access
Foot; Non-
Adjustable
Type label
(M, N models only)
Touchless
Sensors
Power
Connection
Draft Shield
Light
Illuminated
Level
Indicator
(hidden)
Touchless
Sensors with
Indicator Lights

EN-14 EXPLORER BALANCES
3.4 Overview of Parts and Features – Non-Draft Shield Models
Top View
Rear View
Bottom View
Side View
Figure 3-2. Explorer Base (models EX2202, EX4202, EX6202, EX10202, EX6201, EX10201)
Illuminated
Level
Indicator
Touchless
Sensors
Touchless
Sensors with
Indicator Li
g
hts
Type label
(M, N models only)
Data label
Terminal cable
storage clips
Lock switch Weigh
Below
Access
Foot; Non-
Adjustable
Leveling
Thumbwheels
Power
Connection

EXPLORER BALANCES EN-15
3.5 Overview of Parts and Features – Terminal
Top View
Back View
Side View
Figure 3-3. Explorer Terminal
Hooks
(to attach
to base)
Capacity sticker
(Approved models
only)
Touchless
Sensors with
Indicator Lights
Terminal
Bracket
Terminal
Release
Buttons
Angular
Adjust
Buttons
Foot
USB Device
Connection
Terminal
Cable
(from Base)
Terminal
Cable Clamp
RS232
Connection
Option
Port

EN-16 EXPLORER BALANCES
3.6 Functions and Their Icons
Seven Icons are initially available to operate the Balance and access the Menu. These Icons can be customized
based on user preference. For setup information, see User Settings.
3.6.1 Standby
Touch Standby to shut down the display.
Note: After initial start-up (Section 2), in Standby your balance needs no warm-up time and is
immediately available for weighing by touching the Start-up icon.
3.6.2 Printing Data
Touch Print to send the displayed value to a printer or computer via the active COM port.
Note: Ensure proper setup of connections, printing and interface parameters.
Note: Data may also be printed using the Touchless Sensors by configuring these for Printing.
Data may also be printed using the P command from a computer connected to the COM port.
3.6.3 Applications
The balance can be configured to operate in various Application modes.
Touch Applications to choose – or the top button in the Application area.
3.6.4 TouchLess Sensor Status
Explorer balances have four TouchLess sensors that can be assigned a unique function when
activated (e.g., zero, print, tare, etc).
To assign a task for each TouchLess sensor, press Sensors.
Note: To activate a sensor, move an object over it (from a distance of 1-2 inches or 3 cm). The sensor
shows a green light and beeps when activated. If the sensor cannot be activated (sensor is disabled
during certain instances, like when the Menu is displayed) the sensor shows a red light.
3.6.5 AutoCal™
When AutoCal is ON, the balance performs a self calibration. AutoCal will automatically calibrate the
Balance (using the internal mass) each time a change in temperature significant enough to affect
accuracy, or after every 11 hours.
Touch AutoCal™ to initiate. (Default status is ON.)
3.6.6 Menu
Touch Menu to enter the balance’s menu list.
3.6.7 More…
Touch More to access Level Assist, Zero, Tare, Units, Pretare, Cal Test, Calculator, and Stopwatch.
3.6.8 Level Assist
For assistance with Leveling the Balance; the Level Assist screen shows which direction to turn the
thumbwheels to center the level bubble.
3.6.9 Zero Operation
Remove the load from the pan and touch Zero to set the display to zero. When weighing pan is
empty, the >0< indicator turns on when the measurement is within + ¼ division (d) of the zero setting.
Note: The balance also features Auto Zero Tracking (AZT) that automatically maintains a Center of
Zero within the tolerances set in the AZT menu (see Balance Settings).
or
3.6.10 Taring a Container
Taring sets the weight of a container as zero, so only the weight of objects held in the container
(net weight) is displayed.
Manual Tare – Place the empty container on the pan and touch Tare when stable.
Add material to the container. The net weight of the material is displayed.
To clear the Tare value, remove the container from the pan and touch Tare.

EXPLORER BALANCES EN-17
3.6.11 Weighing Units
The balance can be configured to measure in a variety of weighing units, including three (3) custom
units. Touch Units to choose from the displayed list. (Scroll down to see all options.)
Note: The active weighing Unit can also be accessed by touching the unit area of the Main Display
line; If a unit is not displayed in the list, it must first be turned on via the User Menu.
3.6.12 Preset Tare
To enter a Preset Tare, press the Icon and then enter a value;
enter 0 to clear the Preset Tare. The display will show the PT symbol and the tare value as a negative
number.
3.6.13 Calibration Test
is used to compare a known calibration weight against the last stored span calibration data.
3.6.14 Calculator
To use the built-in calculator application, touch Calculator. A four function calculator with addition,
subtraction, multiplication and division mathematical operations is available
•Perform a numeric operation using the keypad.
•Press = to view the result.
•To Clear the display: Press CE to clear the entry, C to clear
all
•Touch x to close and return to the current Application.
3.6.15 Stopwatch
To use the built-in stopwatch application, touch Stopwatch. A countdown timer with interval (lap)
timer is available.
•Press Start to begin using the Stopwatch timer.
•Press Reset to reset the timer to Zero.
•Touch Close to close and return to the current Application.
3.6.16 Logout
Used for User logout and return to User Login screen. This feature is only active if a user profile has
been created and a User has logged in.

EN-18 EXPLORER BALANCES
4. APPLICATIONS
The balance can be configured to operate in various Application modes.
Touch Applications to choose – or the top button in the Application area:
Note: If an application mode does not appear in the list of available Applications it must be enabled in the User
Menu: touch Menu, then select Application Modes. The full list of modes appears. Touch the one you want to
enable. Then touch Enabled in the setup menu for that application mode – Percent Weighing in the example
below. Each enabled mode appears in the Applications menu.
The Explorer Balance incorporates the following Applications.
Weighing Parts Counting Percent
Weighing
Check
Weighing
Dynamic
(Animal)
Weighing
Filling
Totalization Formulation Differential
Weighing
Density
Determination
Peak Hold
(High Point)
Ingredient
Costing
Pipette
Adjustment
Statistical
Quality Control
(SQC)
Library
(complements most Applications)