OHAUS TROOPER COUNT User manual

Trooper Count Scale
Instruction Manual
Balanza Trooper Count
Manual de Instrucciones
Balance Trooper Count
Manuel D'instructions

Trooper Count ScaleTrooper Count Scale
Trooper Count ScaleTrooper Count Scale
Trooper Count Scale 11
11
1
TABLE OF CONTENTS
1. GETTING TO KNOW YOUR TROOPER COUNT SCALE ................................................................................................ 3
1.1 Introduction....................................................................................................................................................... 3
1.1.1 Features .................................................................................................................................................. 3
2. INSTALLATION .................................................................................................................................................... 3
2.1 Unpacking and Checking .................................................................................................................................... 3
2.2 Selecting the Location ........................................................................................................................................ 4
2.3 Connecting Power .............................................................................................................................................. 4
2.3.1 Battery Installation .................................................................................................................................... 4
2.3.2 AC Power ................................................................................................................................................. 4
2.4 Leveling the Scale .............................................................................................................................................. 4
2.5 Stabilization ..................................................................................................................................................... 4
3. OPERATION ....................................................................................................................................................... 5
3.1 Overview of Controls and Display Functions ........................................................................................................ 5
3.2 Basic Weighing ................................................................................................................................................. 7
3.2.1 Turning On the Scale ................................................................................................................................ 7
3.2.2 Turning Off the Scale ................................................................................................................................. 7
3.2.3 Zero Operation .......................................................................................................................................... 7
3.2.4 Weighing ................................................................................................................................................. 7
3.2.5 Manual Tare Operation .............................................................................................................................. 8
3.2.6 Pre-Set Tare Operation............................................................................................................................... 8
3.2.7 Gross/Tare Recall Operation....................................................................................................................... 8
3.2.8 Unit Switch Operation ................................................................................................................................ 8
3.3 Basic Counting .................................................................................................................................................. 9
3.3.1 Positive Sampling ..................................................................................................................................... 9
3.3.2 Negative Sampling .................................................................................................................................... 9
3.3.3 Positive Counting .................................................................................................................................... 10
3.3.4 Negative Counting ................................................................................................................................... 10
3.3.5 Using Keypad to Edit Counting Data ......................................................................................................... 11
3.4 Library Mode ................................................................................................................................................... 11
3.4.1 Library Operation .................................................................................................................................... 11
3.4.2 Entering Data Directly into Library ............................................................................................................ 11
3.4.3 Saving Library Data ................................................................................................................................ 13
3.4.4 Saving Library Data in Another Location................................................................................................... 13
3.4.5 Using the Library..................................................................................................................................... 14
3.5 Auto Optimization............................................................................................................................................. 14
3.6 Auto Add Mode ................................................................................................................................................ 14

22
22
2Trooper Count ScaleTrooper Count Scale
Trooper Count ScaleTrooper Count Scale
Trooper Count Scale
TABLE OF CONTENTS (Cont.)
3.7 RS232 Communications ..................................................................................................................................... 15
3.7.1 RS232 User Command Table ..................................................................................................................... 15
3.7.2 Output Formats ......................................................................................................................................... 15
3.7.3 RS-232 Pin Out ......................................................................................................................................... 15
4. SETUP............ ................................................................................................................................................... 16
4.1 Setup Protection................................................................................................................................................. 16
4.2 Menu Structure................................................................................................................................................... 16
4.3 Control Functions ............................................................................................................................................... 17
4.3.1 Menu Operation ........................................................................................................................................ 17
4.4 Checking the Menu Settings ................................................................................................................................ 17
4.5 Setup Menu ....................................................................................................................................................... 18
4.6 Read Menu ........................................................................................................................................................ 19
4.7 Print Menu ........................................................................................................................................................ 19
4.8 Count Menu ....................................................................................................................................................... 21
4.9 Lockout Menu .................................................................................................................................................... 22
5. CALIBRATION AND SEALING ................................................................................................................................. 23
5.1 Span Calibration ................................................................................................................................................ 24
5.2 Linearity Calibration ........................................................................................................................................... 25
5.3 Legal for Trade Operation and Sealing ................................................................................................................ 27
6. CARE AND MAINTENANCE ................................................................................................................................... 28
6.1 Troubleshooting ................................................................................................................................................. 28
6.2 Error Codes List ................................................................................................................................................. 29
6.3 Service Information ............................................................................................................................................ 29
6.4 Accessories ....................................................................................................................................................... 29
7. TECHNICAL DATA ............................................................................................................................................... 30
7.1 Counting Limits .................................................................................................................................................. 30
7.2 Specifications .................................................................................................................................................... 32
7.3 Compliance ....................................................................................................................................................... 33

Trooper Count Scale 3
1. GETTING TO KNOW YOUR TROOPER COUNT SCALE
1.1 Introduction
Thank you for deciding to purchase a Trooper Count Scale from Ohaus. The Ohaus Trooper Count Scale is a rugged,
reliable, electronic counting/weighing scale designed for easy operation.
Behind your instrument stands Ohaus, a leading manufacturer of precision Indicators, Scales and Balances. An After-
market Department with trained instrument technicians is dedicated to providing you with the fastest service possible in
the event your instrument requires servicing. Ohaus also has a Customer Service Department to answer any inquiries
regarding applications and accessories.
To ensure you make full use of the possibilities offered by your Trooper Count Scale, please read the manual completely
before installation and operation.
1.1.1 Features
Major features include:
• Three backlit LCDs
• Durable cast aluminum internal frame, stainless steel weighing pan, ABS housing
• 21 button operation with numeric keypad
• Flexible unit switching-lb/kg/oz/g
• RS232 serial communication interface
• Battery operation with internal 6 C-cell batteries
• AC power adapter
• Auto shut off for power saving
• Library feature saves counting data for 60 items. (Part number, APW, tare values, over/under values,
and count totals.)
• Positive or negative sampling and counting
2. INSTALLATION
2.1 Unpacking and Checking
Open the package and remove the instrument and the accessories. Check the instrument for transport damage. Imme-
diately inform your Ohaus dealer if you have complaints or if parts are missing. Your Trooper Count Scale package
should contain:
• Trooper Count Scale • Instruction Manual
• Weighing Platform • Warranty card
• AC power adapter
Store all parts of the packaging. This packaging ensures the best possible protection for the transport of your instrument.
NOTE: Remove the two shipping screws if present on top of the unit.

4 Trooper Count Scale
2.2 Selecting the Location
The Scale should be used in an environment which is free from dust, water, corrosives, vibration or temperature
extremes as these factors can affect scale accuracy. The Scale should be located on a stable level surface and kept
away from vibrating sources such as large machinery.
2.4 Leveling the Scale
To compensate for small irregularities or inclinations at the location, the Scale can be leveled. The Scale is equipped
with a level indicator located at the rear. Adjust the leveling feet until the air bubble in the indicator is centered as
shown.
NOTE: The instrument should be leveled each time its location is changed.
2.5 Stabilization
Before initially using the Scale, allow time for it to adjust to its new environment. The recommended warm up period is
five (5) minutes if the Scale is already stabilized to room temperature.
2.3 Connecting Power
2.3.1 Battery Installation (If desired)
Remove battery cover and insert 6 Alkaline C-type batteries into the battery holder making sure that the batteries are
properly orientated. The negative battery terminals should face the spring contacts.
NOTE: It is recommended that when the Trooper Count Scale is operated from batteries, the Auto-Off Timer feature be
turned on to extend battery life. When setting up the Scale, refer to the Setup menu, section 4.5.
2.3.2 AC Power
Verify that the AC power source matches the AC adapter rating. Connect the Adapter power cord at the rear of the Scale
and plug the Adapter into a convenient power outlet.

Trooper Count Scale 5
No. Designation Function
1 Weight Display Displays current weight on scale.
Indicators identify active weight unit and Net or Gross weight:
kg (Kilogram) – Unit of measure.
g(Gram) - Unit of measure.
lb (Avoirdupois Pound) - Unit of measure.
oz (Avoirdupois Ounce) - Unit of measure.
Net (Net weight) – Gross weight minus Tare.
2 Data Display Displays user selected data.
Indicators show active data mode:
B/G (Brutto/Gross) – Total weight of items.
%AC (Percent Count accuracy) – Estimated accuracy of the count based on sample
size and scale resolution.
T(Tare value) – Weight of the container.
PT (Preset Tare value) – Tare value recalled from memory or entered via keypad.
APW (Average Piece Weight) – Average weight of one item.
MR (Memory Recall) – Accumulated quantity stored in memory.
3 Count Display Displays current count of items on the scale.
Indicators show count status:
M(Memory) – Accumulated quantity in memory.
<(Under) – Current quantity is less than lower limit.
>(Over) – Current quantity is more than upper limit.
< > (Target range) – Current quantity is between upper and lower limits.
PCS (Pieces) – A count value is being shown.
3.1 Overview of Controls and Display Functions
ON/ZERO
Off PRINT
Units SAMPLE Menu LIBRARY
Save TARE
789
456
123
0.
DATAWEIGHT COUNT
The counting feature is not legal for trade
ozkg g lb Net B/G %Ac T PT APW MR M < > PCS
Data
Clear
M+
M-
Enter
123 4
5
6
7
8
9
10
11
1213
14
3. OPERATION

6 Trooper Count Scale
No. Designation Function
4 Numeric Keypad Enter specific values for tare, APW and other data entries.
5 Data button Selects between data modes in the Data display.
In edit mode, serves as a “Go Back” or backspace key.
6 Clear button During editing, clears the blinking entry.
7 M+ button Adds the displayed quantity into the accumulating memory.
During editing, selects the next higher option or number.
8 M- button Subtracts the keyboard entry from the accumulating memory. In sampling mode,
enters negative sampling.
During editing, selects the next lower option or number.
9 Enter button Enters edit function of current mode. If current mode does not support edit func-
tions, an error beep will occur.
In edit mode, accepts entry.
10 TARE button Tares the weight on the pan or accepts the keypad tare entries.
11 LIBRARY
Save button Short press displays Library ID (blinking) and the part number. Repeat press
returns to weigh/count mode.
Long press (3 seconds) saves library changes.
12 SAMPLE
Menu button Short press enters the sampling mode.
Long press (3 seconds) enters scale setup menu. In menu mode, a short press
will return to weigh mode.
13 PRINT
Units button Short press sends data to RS232 port.
Long press (3 seconds) steps through active weigh units. Release on desired
unit.
14 ON/ZERO
Off button Short press turns the scale on or zeros the display.
Long press (3 seconds) turns the scale off.
3.1 Overview of Controls and Display Functions (Cont.)

Trooper Count Scale 7
3.2 Basic Weighing
The Trooper Count Scale has been factory calibrated and is ready for operation. Ohaus recommends that the Scale be
re-calibrated before use to ensure optimal accuracy. You can operate the scale at this point using the factory default
settings. You can check the default menu settings on page 14. All bolded items on the menu are the factory default
settings. The scale will operate in the default mode. If you want to change the settings, continue with Section 4, Setup.
When the Scale is positioned for operation, follow the operational procedure outlined next.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
3.2.1. Turning On the Scale
Press and hold ON/ZERO Off button until the LCD
display appears. The display cycles as shown below
displaying "Ohaus", with model number, serial num-
ber, software revision number and weighing mode
display.
3.2.2 Turning Off the Scale
To turn the Scale off, press and hold the ON/ZERO Off
button until OFF is displayed.
3.2.3 Zero Operation
Press the ON/ZERO Off button to zero the weight dis-
play. The gross weight is also shown in the DATA
display.
NOTE: A pre-set tare value will not be zeroed.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
3.2.4 Weighing
Place item to be weighed on the Scale. The display
indicates a sample of 1.5kg, gross weight.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT

8 Trooper Count Scale
Place the container on the Scale. Display shown is
0.5kg.
Press TARE button. The container is tared, the Net
weight is shown in the WEIGHT display, and the Tare
weight is shown in the DATA display.
To clear the tare with an empty pan, press the TARE
button.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
3.2.7 Gross/Tare Recall Operation
Repeatedly press the Data button to cycle through
Gross and Tare readings.
3.2.6 Pre-Set Tare Operation
Pre-Set Tare is a tare value that is entered using the
numeric keypad. To use Pre-Set Tare, repeately press
the Data button until the PT indicator is shown in the
DATA display. The DATA display indicates OFF.
Press the Enter button to toggle the Pre-Set Tare on or
off. The current Pre-Set Tare value (if any) is displayed.
Enter a numeric value using the keypad, (the COUNT
display is blinking), then press the Enter button. The
Net weight is shown in the WEIGHT display and the
tare weight is shown in the DATA display. Display
shown is 0.5kg.
Alternate Method:
Pre-Set Tare can also be entered using the numeric
keypad, then press the TARE button.
NOTE: The Pre-Set Tare value is overwritten when a
new value is entered.
3.2.8 Unit Switch Operation
Press and hold PRINT Units button until display
changes to selected measuring unit. Display indica-
tors at the bottom of the WEIGHT display indicate the
active weighing unit. Depending on which units are
enabled in the Read menu, you have a choice of g,
lb, kg or oz. The display sample indicates a 1kg
load changed to lb.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
3.2.5 Manual Tare Operation
When weighing a sample that must be held in a container, taring stores the container weight memory.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT

Trooper Count Scale 9
3.3 Basic Counting
Read this procedure entirely before counting pieces. Piece sampling and counting can be further enhanced using menu
selections in the Count menu. There are several methods that are available for sampling.
• Positive Sampling - given number of pieces are placed on the scale, the weight is divided by the number of pieces
to calculate the Average Piece Weight (APW). Additional pieces are then placed on the scale and counted and dis-
played.
• Negative Sampling - calculates the APW when a given number of pieces are removed from the total quantity.
• The APW can also be entered through the numeric keypad. As parts are placed on the scale, the count is
immediately displayed.
• The Trooper Count will support positive counting or negative counting.
3.3.1 Positive Sampling
If a weighing container is to be used:
• If the tare value is known, enter a Pre-Set Tare.
• If the tare value is not known, place the container
on the pan and press the TARE button.
Press the SAMPLE
Menu button.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
M<> PCS
COUNT
M<> PCS
COUNT
The display indicates to place 10 samples on the scale. Place the desired number of sample pieces in the container.
If you have placed 10 pieces in the container, press the Enter button, or by pressing the numeric keys you may directly
enter an alternate sample size. Increased sample size results in better results. If you make a mistake, press the Clear
button and start again. Press the Enter button. The example indicates a sample size of 10 pieces.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
NOTES:
1. If APW is less than minimum, [Err3] [LOW]
[APW] is displayed. See section 6.2.
2. If Ref. Wt. is less than minimum, [Err4] [LOW]
[REF] is displayed. See section 6.2.
3.3.2 Negative Sampling
Negative sampling permits the determination of the total quantity on the pan by removing a known number of sample
pieces. The total quantity may be placed directly on the Scale or in a container. The Trooper Count Scale automatically
calculates the remaining pieces after the sample amount is removed. When a container is used, you may enter a
preset tare weight or simply tare the empty container before starting.

10 Trooper Count Scale
Press the SAMPLE Menu button.
Press the M- button.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
M<> PCS
COUNT
M<> PCS
COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
M<> PCS
COUNT
M<> PCS
COUNT
Place the total number of pieces on the pan, then press the Enter button.
M<> PCS
COUNT
M<> PCS
COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
Remove 10 pieces as instructed, or use the keypad to change the number of pieces to be removed, then press Enter
button.
Place the pieces that were removed back on the scale
to display the total number of pieces.
NOTE: If AUTO-ADD is ON, the Scale may direct you to
remove additional pieces if the reference weight is too
small.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
If a weighing container is to be used:
• If the tare value is known, enter a Pre-Set Tare.
• If the tare value is not known, place the container on the pan and press the TARE button.
3.3.2 Negative Sampling (Cont.)
3.3.3 Positive Counting
After sampling, place additional pieces on the scale and view the piece count in the COUNT display.
3.3.4 Negative Counting
After sampling, place the entire quantity of pieces on the scale. Press the ON/ZERO Off button. As pieces are removed,
the quantity removed is shown in the COUNT display as a negative number.

Trooper Count Scale 11
3.4 Library Mode
The Trooper Count scale allows the storage of part/counting data in 60 locations, designated ID 00 to ID 59. Each
location includes: part number, Average Piece Weight (APW), a pre-set tare value, over and under count values and an
accumulated piece count.
Data in the library is saved in a manner similar to a computer file. Temporary editing of the data will not affect the saved
data. When desired, the temporary edits can be saved, allowing the scale to be turned off without losing the changes.
Data in ID 00 may not be saved permanently but the data can be easily copied to another location.
The Library, ID 01 to ID 59, can be locked (see 4.9 Lockout Menu) to prevent unauthorized changes to the data. The
accumulated count will not be locked allowing it to be updated. When turned on, the scale defaults to ID 00.
3.4.2 Entering Data Directly into Library
The following example is used to illustrate how to enter data in a particular library location.
Short press on the LIBRARY
Save button.
Short presses on the M+ or M- buttons will display
library locations which are already used.
Using the numeric keys, enter the desired library num-
ber. The sample shown is an empty location, ID 22.
Press the Enter button to accept ID 22.
Press the Enter button, to edit the part number or press
M+ to skip.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
3.3.5 Using Keypad to Edit Counting Data
The APW, Pre-Set Tare (PT) and the accumulated count (MR) can be viewed and edited in the DATA window. While
in weigh mode repeatedly press the Data button until the APW indicator is lit. A new APW value may be entered via
the keypad and accepted with an Enter press. PT and MR can also be similarly edited.
3.4.1 Library Operation
To enter the Library, momentarily press the LIBRARY Save button. A short press in Library mode will exit to weigh
mode.
• M+ and M- buttons advance through the blinking choices.
• The Enter button accepts the blinking choice.
• The Data button returns to the previous choice.
• The Clear button will clear blinking data or back space during data entry.
• Three rapid beeps indicates an error, an improper button press or data value.

12 Trooper Count Scale
Using the numeric keys 0-9, enter the desired part
number. For this example, we will use 1230000000.
You will notice that the part number can be up to 12
digits and utilizes the DATA and COUNT display win-
dows. Press the Enter button to confirm the entry.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
BLINKING
3.4.2 Entering Data Directly into Library (Cont.)
Press the M+ button, the display advances to APW.
Press the Enter button to access APW value.
Using the numeric keypad, enter the APW. Sample
shown indicates an average piece weight of 2g. Press
the Enter button to accept.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
BLINKING
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
Press the M+ button to advance to setting the preset
tare. Press the Enter button to access the tare value.
Using the keypad, enter the desired tare weight. The
sample shown is 50g. Press the Enter button to ac-
cept.
Press the M+ button to advance to Under count.
Press Enter button to access the under count value.
Using the numeric keypad, enter the desired under
count limit. For this sample, we will use 95. Press
the Enter button to accept.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
Press M+ to advance to over count. In this sample,
we are using 105 pieces.
Press Enter button to access over count value. Using
the numerical keypad, enter the desired over count
limit (must be greater than under count value). Press
the Enter button to accept.

Trooper Count Scale 13
Press M+ to advance to count. Count is the accumu-
lated piece count in memory. Press Enter button to
edit count value.
Using the numeric keypad, enter the desired count.
The sample illustrates 250 pieces. Press the Enter
button to accept.
To exit library editing, momentarily press the Library
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
3.4.2 Entering Data Directly into Library (Cont.)
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
To save the settings, use a long press on the
Library
Save button. The library location (ID 22)
and UPDATE YES is displayed.
Press Enter button to accept save location. Press
Enter button again to save changes.
3.4.3 Saving Library Data
Temporary changes to a library location need to be
permanently saved or the changes will be lost when
the scale is turned off. The scale will recommend
saving temporary changes when the library location
is changed or when the scale is turned off.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
The UPDATE DONE display confirms a successful save.
3.4.4 Saving Library Data in Another Location
You have the option of copying all data from one li-
brary location into another library location. In the
following example, we will save data from library lo-
cation 22 to 52. Library 22 is shown.
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
Make a long press on LIBRARY Save button until
display indicates UPDATE.
Enter the desired new location directory using the nu-
meric keypad or by pressing the M+ button to ad-
vance to the next open location. The sample is loca-
tion 52. Press the Enter button.

14 Trooper Count Scale
Press the Enter button to save data.
UPDATE DONE, then the ID number with IN USE will
be displayed momentarily followed by the counting
display.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
3.5 Auto Optimization
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
3.4.4 Saving Library Data in Another Location (Cont.)
Automatic reference optimization results in a more accurate count by increasing the reference weight without the need
to count additional parts. A higher reference weight is important when there is a risk of inconsistent piece weights or if
the reference weight is close to the minimum (See section 7.1).
Auto Optimization uses an initial APW to count additional pieces that are placed on the scale. After a few seconds, the
message A-OPt appears in the Data display as the new higher reference weight is used to re-calculate the APW. The
process can be repeated as long as the additional weight is less than the previous reference weight. Once this limit is
exceeded Auto-Opt is turned off. This function can be activated or deactivated in the Count menu. The factory default
setting is on.
3.6 Auto Add Mode
Auto Add Mode is setup for a more accurate count procedure by increasing the minimum reference weight and the
minimum APW limits (see section 7.1). The scale requests additional pieces if the reference weight is less than the
recommended Auto-Add minimum weight in Table 7-2. The instructions to add these additional pieces may be ig-
nored. This function can be activated or deactivated in the Count menu. The factory default setting is off.
Place the stipulated number of pieces on the scale
(e.g. 2 pieces). The scale then determines the new
APW based on the total pieces
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
3.4.5 Using the Library
To enter the Library, momentarily press the LIBRARY Save button. Use the keypad or the M+ button to enter a location
ID that you wish to use. Press the LIBRARY
Save button again to select the new ID. ID XX IN USE will display indicating
that the data stored in that memory is now active. If an APW and a Preset Tare was set, placing a sample filled
container on the scale will give an immediate count.
If the Library is not locked, it is possible to edit the data in the current ID. The changes need not be saved if they were
for temporary use. If the Library is locked, you must change to ID 00 for simple counting use.
At this point, all data from Library 22 has been copied
into Library location 52.

Trooper Count Scale 15
3.7 RS232 Communication
All communication is accomplished using standard ASCII format. Characters shown in the following table are acknowl-
edged by the Scale. Invalid command response "ES" error indicates the Scale has not recognized the command.
Commands sent to the Scale must be terminated with a carriage return (CR) or carriage return-line feed (CRLF). Data
output by the Scale is always terminated with a carriage return-line feed (CRLF). See section 4.7 for RS232 and Print
Setup.
Command Description
Character (LFT is OFF)
PSame as pressing PRINT button. Sends print data to peripheral device.
VOutput software version. For example: "TC30 Sr. 1.20"
TSame as pressing TARE. If the Scale accepts the command, it will respond "OK".
If the Scale is in motion, it will output "CANT TARE" until the Scale is stable. When stable, tare is
accepted. (NOTE: If LFT is ON, special tare rules apply.)
ZSame as pressing ZERO button. If the Scale accepts the command, it will respond "OK".
NOTE: Any other command will produce the answer "ES".
3.7.1 RS232 User Command Table
Data output can be initiated by: 1) By pressing PRINT Units button or, 2) Sending a print command (“P”) from a
computer. The two available output styles are shown below.
3.7.2 Output Formats
OHAUS
TROOPER COUNT
TC3RS SN: 222222
PART# = 123456789000
COUNT = 38
TOTAL = 188
APW = 5.000 g
NET = 190 g
TARE = 10 g
GROSS = 200 g
OHAUS
TROOPER COUNT
TC3RS SERIAL No. : 222222
(WEIGHT UNIT = g)
PART No. COUNT TOTAL APW NET TARE GROSS
123456789000 138 326 5.000 690 10 700
"Column" Print Style "Line" Print Style
1 N/C
2 Data In (RXD)
3 Data Out (TXD)
4 N/C
5 Ground
6, 7, 8, 9 N/C
3.7.3 RS-232 Pin Out.
The adjacent table illustrates the pin-out connections
on the Female 9-pin D-sub connector.

16 Trooper Count Scale
4. SETUP
For first time setup, step through all menus and set the parameters as desired.
4.1 Setup Protection
The Trooper Count Scale is equipped with menus which permit certain functions to be locked out (not changed) during
operation. If you intend to physically lock out changes to the setup selections, you will need to access the hardware
Lock Switch located on the main circuit board following the setup procedure.
4.2 Menu Structure
The following table illustrates the menu structure in the Trooper Count Scale.
CAL SETUP READ PRINT LOCSW
Span
Lin
Reset
yes,no
LFT
on,off
Cal Unit
lb, 1000g
Cal Point
1/3, 2/3, Full
Beeper
All, signal, off
Backlight
on, off, auto
Auto Off Timer
on (5 min), off
Library
On,OFF
Unit g
on, off
Unit kg
(1000g)
on, off
Unit lb
on, off
Unit oz
on, off
Auto Zero
Tracking
0.5*, 1, 3, off
Baud Rate
1200, 2400, 4800,
9600, 19200
Data Length
7,8
Parity Bit
none, Even, Odd
Print Part No.
on, off
Print COUNT
on, off
Print APW
on, off,
Print Net
on, off
Print Tare
on, off
Print TOTAL pcs
on, off
Print Gross
on, off
Print On Stable
off, 0.5d, 1d*, 3d
Print Header
on, off
Print STYLE
Col, Line
CAL Lock
on, off
Setup Lock
on, off
Read Lock
on, off
Print Lock
on, off
Count Lock
on, off
Library
Lock
on, off
COUNT
Auto Add
off, on
Print Clear
on, off
Auto Opt.
on, off
M requires
10d chg.
on, off
NOTE: Bolded items indicate factory defaults.
* LFT on setting

Trooper Count Scale 17
4.3.1 Menu Operation
• To enter menus, press and hold SAMPLE Menu button. A short press in menu mode will exit to the weigh mode.
•M+ and M- buttons advances through blinking choices.
•Enter button accepts blinking choice.
•Data button returns to the next higher menu level. At top level, it exits the menu operation.
• Three rapid beeps indicates an improper button press.
4.4 Checking the Menu Settings
Each of the menus in the Trooper Count Scale can be quickly checked to see if any of the parameters need to be
changed to match your requirements. The default settings are shown as bolded entries on the menu structure, section
4.2. Review the menu structure to determine what settings have to be changed.
To enter the menus, press and hold the SAMPLE
Menu
button until CAL MENU is displayed.
Repeated pressing of the M- button will traverse
through the (6) menus in the order shown. You may
go back by using the M+ button. To leave the menus,
press the Data button.
To enter a selected menu (blinking), press the Enter
button, then scroll through all settings by repeately
pressing the M+ or M- buttons. In this manner, you
can quickly check all settings for any particular menu.
All menu settings are saved once they are changed.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
BLINKING
BLINKING
The LOC MENU SW ON appears if the lockswitch un-
derneath the scale is set on. This prevents the set-
tings from being changed (as in a Legal For Trade
application). See section 5.3 for details.
LOC ON indicates that the menu has been locked in
the Loc Menu. You may view the menu parameters,
but they may not be changed. See section 4.9 Lock-
out menu for details.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
4.3 Control Functions
The Scale has six menus; CAL, SETUP, READ, PRINT, COUNT and LOCSW which are entered by pressing and holding
the SAMPLE
Menu button until CAL MENU is displayed, then releasing it. During setup, the M-, M+, Enter and Data
buttons are used to traverse and enter the menus.

18 Trooper Count Scale
4.5 Setup Menu
Procedure
With the Scale ON, press and hold the SAMPLE Menu
button until CAL MENU is displayed.
NOTE: The calibration menu is covered in Section 5.
Press M- button to advance to SETUP MENU, then
press Enter button. Navigate through the menu as
explained in section 4.3.1.
Press Enter button to get into the RESET sub-menu.
YES will change all menu settings to their default set-
tings. Library data will not be affected.
ON will set the Scale to LFT configuration. In the ON
setting, the zero setting will be limited to +/- 2%. In
the OFF setting, the zero setting is 100%. Also, in the
ON setting, the LFT readability is set. In the OFF posi-
tion, the readability is set to the Enhanced value.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
BLINKING
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
Three setting are available, ALL, SIGNAL and OFF.
ALL = the beeper sounds when buttons are pressed or
when error or target signals are needed. SIGNAL =
beeps on errors (three beeps) or at count target (con-
tinuous). OFF = is always off.
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
kg glb oz Net B/G %Ac TPT APW MR M<> PCS
WEIGHT DATA COUNT
Selected calibration units are either lb or 1000g (kg).
A selection of 1/3, 2/3 or full span calibration values
are available. The numeric values of the calibration
points are displayed for the specific Scale capacity
and calibration unit.
Backlight has three available settings; ON, OFF, AUTO.
ON = backlight is always on. AUTO = backlight turns
on with any key press or a weight change (5d) and
remains on for 5 seconds. OFF = backlight is always
off. OFF or AUTO is recommended for battery opera-
tion.
ON = Scale turns off in 5 minutes if no key press or
weight changes (5d) are detected. OFF = auto off
feature is disabled. ON is recommended for battery
operation.