Ohlins HO424 User manual

Shock Absorber for Honda MSX125
HO424
Mounting Instructions
Note!
Please note that this image is a general representation
of the product and may differ slightly from your product.
Note!
Please note that during storage and transportation,
especially at high ambient temperature, some of the oil
and grease used for assembling may leak and stain the
packaging. This is in no way detrimental to the product,
wipe off the excessive oil/grease with a cloth.
Note!
Before installing this product, check the contents of the
kit. If anything is missing, please contact an Öhlins dealer
.
Warning!
Before installing this product, read the Öhlins Owner’s
Manual. The shock absorber is an important part of your
vehicle and will affect the stability.
Kit Contents
Description Part No Pcs
HO424 1
01185-01 2
01185-04 2
00710-01 2
Shock absorber
Sticker Öhlins
Sticker Öhlins
C-spanner
Owners manual 07241-02 1

2
MOUNTING INSTRUCTIONS
1
Put the motorcycle on a center stand so that
the rear wheel barely touches the ground.
Make sure the motorcycle is in a stable
position.
2
Remove the fairing on left side. First remove
the screw. Then push the center rivet pin with a
small pin to release it.
3
Loosen the upper and the lower bolts of shock
absorber.
4
Mount the Öhlins shock absorber onto the
motorcycle.
5
Tighten the upper and the lower bolts according
to HONDA service manual.
6
Reload the rivet the side fairing.Push the
center pin back into original position.
7
Remount the left fairing.
Warning!
It is advisable to have an Öhlins dealer install the shock
absorber.
Warning!
If working on a raised vehicle, ensure it is securely
supported so that it will not tip over.
Note!
Before mounting this product clean the vehicle
thoroughly.
Note!
When working on this product, always see the Vehicle
Service Manual for vehicle specic procedures and
important data.
Note!
Lower the vehicle so that the suspension is slightly
compressed before tightening the screws.
Caution!
Ensure that all screws are tightened to the correct
torque and that nothing fouls or restricts movement
of the shock absorber when the suspension is fully
compressed or extended.
8
Retighten the screws on the side fairing
according to HONDA service manual.
9
Lock the rivet by pushing in the center pin.

3
MOUNTING INSTRUCTIONS

Öhlins Asia Co., Ltd
700/937 Moo 5,
Tambol Nongkhaka,
Amphur Phantong, Chonburi 20160
Thailand
© Öhlins Asia Co. Ltd. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
SET-UP DATA
Warning!
Before riding, always make sure that the basic settings
made by Öhlins are according to recommended
Set-up Data. Read about adjustments and setting up
in the Öhlins Owner’s Manual before you make any
adjustments. Contact an Öhlins dealer if you have any
questions about setting up.
ADJUSTMENTS
Part no. MI_HO424_EN_0
Issued 2015-03-02
Recommended set-up
Spring Preload ............................ 7 mm
Compression adjuster ................. 14 Clicks
Rebound adjuster......................... 8Clicks
Spring
Part No ....................................... 60281- 07
Free spring length ....................... 135 mm
Shock absorber data
Length ......................................... 244 mm
Stroke ......................................... 40 mm
Spring Preload
Adjuster
Rebound
Adjuster
Compression
Adjuster
Preload adjustment range ..............[0-19] mm