Ohlins SU 145 User manual

Owners Manual
Mounting instructions Öhlins shock absorber kit
SU 145 for Suzuki GSX 1100
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the
written permission of Öhlins Racing AB is prohibited. Printed in Sweden.
Öhlins shock absorber 36 PRCLB
Your Öhlins shock absorber type 36 PRCLB features
the following adjusters:
Compression damping adjuster
Adjustments are made with the wheel on top of the
reservoir. The adjustments are made in four (4) steps.
Rebound damping adjuster
Adjuster wheel on the piston shaft above the end
bracket.
Spring preload adjuster
Adjustments are made by turning the knob on the hy-
draulic adjuster. Clockwise for harder adjustment,
counter clockwise too release the preload.
Lenght adjuster
Adjustment is made by turning the end eye and tight-
ening with the lock nut.
NOTE!
When delivered the Öhlins shock absorber is dialed to
recommended settings for the specific brand and make
of the motorcycle. If you have changed the setting
check like this:
The adjusters have a normal right hand tread. Turn the
damping adjusters clockwise to fully closed (pos. zero [0]).
Turn counter clockwise to open and count the clicks until
you reach the recommended number of clicks. See Setup
data at page 4.
CAUTION!
Do not use to much force, delicate sealing surfaces
can be damaged.
Spring
preload
adjuster
Rebound
damping
adjuster
Lenght
adjuster
Compression
damping adj.Checking sag and ride height
Front suspension
F1. Bike on a stand with the
suspension fully extended = ............
F2. Bike on the ground without rider = ............
F3. Bike on the ground with rider = ............
Free sag F1 - F2 = ............
Ride height F2 - F3 = ............
Rear suspension
R1.Bike on a stand with the
suspension fully extended = ............
R2.Bike on the ground without rider = ........... .
R3.Bike on the ground with rider = ............
Free sag R1 - R2 = ............
Ride height R2 - R3 = ............
NOTE!
If ride height is higher than recommended,
softer spring/springs must be used.
If ride height is lower than recommended,
harder spring/springs must be used.
Contact your Öhlins dealer for advice.
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone [phone]. Fax [phone].
www.ohlins.com
Part No. SU 145. Issued 02 02 13
Setup data
Shock absorber length 330.5 (+10/-0) mm
Shock absorber stroke 83 mm
Spring preload 16 mm
Rebound damping adjuster 12 clicks
Compression damping adjuster 02 clicks
Bike on a stand.
F1
R1
Bike on the ground.
F2
R2
Bike with rider on.
F3
R3

Before installation
Öhlins Racing AB can not be held responsible for
any damage whatsoever to shock absorber or
vehicle, or injury to persons, if the instructions for
fitting and maintenance are not followed exactly.
Similarly, the warranty will become null and void
if the instructions are not adhered to.
WARNING!
1. Installing a shock absorber, that is not
approved by the vehicle manufacturer, may
affect the stability of your vehicle. Öhlins
Racing AB cannot be held responsible for
any personal injury or damage whatsoever
that may occur after fitting the shock
absorber. Contact an Öhlins dealer or other
qualified person for advice.
2. Please study and make certain that you
fully understand all the mounting instructions
and the owners manuals before handling this
shock absorber kit. If you have any questions
regarding proper installation procedures,
contact an Öhlins dealer or other qualified
person.
3. The vehicle service manual must be
referred to when installing the Öhlins shock
absorber
Safety signals
Important information concerning safety is
distinguished in this manual by the
following notations:
The Safety alert symbol means:
Caution! Your safety is involved.
WARNING!
Failure to follow warning instructions
could result in severe or fatal injury
to anyone working with, inspecting or
using the suspension, or to bystanders.
CAUTION!
Caution indicates that special pre-
cautions must be taken to avoid dam-
age to the suspension.
NOTE!
This indicates information that is of
importance with regard to procedures.
Öhlins products are subject to continual improve-
ment and development. Consequently, although
these instructions include the most up-to-date
information available at the time of printing, there
may be minor differences between your suspen-
sion and this manual. Please consult your Öhlins
dealer if you have any questions with regard to
the contents of the manual.
NOTE!
During storage and transportation, espe-
cially at high ambient temperature, the oil
and grease used for assembling may run out
inside the packing and damage the
expanded polystyrene packing material. This
is not unusual and is in no way detrimental
to the shock absorber.
Kit contents
Before installing the shock absorber, please
check the contents of the kit, listed on the front
page of this instruction. If anything is missing,
contact your Öhlins dealer.
Description Pcs. Part No.
Shock absorber 36PRCLB 2 SU 145
Washer 2 0422-01
Washer 2 3118-15
Bolt 10x40 2 0429-01
Nut M10 2 0430-01
Sticker Öhlins 2 00192-01
Owners manual 1
WARNING!
1. It´s advisable to have an Öhlins dealer or other
qualified person to fit your shock absorber.
2. Instructions in the vehicle service manual are
to be followed when changing the shock
absorber.
3. When working on a lifted vehicle it must be
securely supported to prevent it from falling.
NOTE!
Make sure that all bolts are tightened to the correct
torque and that nothing fouls or restricts movement
of the shock absorber when the suspension is
being fully compressed or extended.
Mounting instructions
1
Put the motorcycle on a stand so the rear wheel
is clear of ground. Make sure it’s steadily fixed
so it will not fall over.
NOTE!
The shock absorber shall be mounted with the
cylinder head upwards and the reservoir back-
wards. Use the supplied washers to fit the shock
absorber on your bike.
2
Loosen and remove the standard shock absorb-
ers. See the motorcycle’s Workshop maual.
3
Fit the Öhlins shock absorbers in the same posi-
tion as the standard shock absorber.
WARNING!
If the shock absorber has an ad-
justable end eye/bracket, this
must not be treaded out more
than that one groove is fully vis-
ible beneath the lock nut. Make
sure that the lock nut is tightened
after adjustment.
Groove
4
Contionue yor work according to the Owners
Manual, section Adjustments.
ø10.5/ø 22.4
ø12.1/ø 24
Wheel side
Rearwards
❿
❿