olympia electronics Slim Light Series User manual

‘’ Slim Light ‘’ SERIES FOR MAINTAINED / NON-MAINTAINED LUMINAIRES
Thank you for purchasing this product of
O l y m p i a E l e c t r o n i c s . A E u r o p e a n
manufacturer.
GENERAL
o
These luminaires are used indoors (ta 40 C)
where emergency light is needed.
Each l u mina i re mus t be per m anen t ly
connected to mains power supply. In normal
operation the illumination LEDs are lit as well
as the green indicating charge LEDs when
the battery is charging.
In case of a mains power supply failure the
luminaire will light the led strip automatically
in emergency mode. When the mains power
supply is restored the device turns to normal
operation.
Maintained / non-maintained operation
there is an option to select the maintained or
non-maintained operation by placing the
jumper to the appropriate place according to
the figure 3 (page 2).
INSTALLATION
To install the luminaire follow the installation
instructions on page 2.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only.
2. The device must be connected to the
mains power supply thru a fuse dependent by
the total amount of the line’s power load.
3. It is sugested to check every month the
indication LED for battery charging, and by
pushing the TEST button to check the
emergency circuit. The led strip should light as
long as the TEST button is pressed.
4. It is sugested to check every 6 months the
m i n i m u m a u t o n o n o u s d u r a t i o n b y
disconnecting the mains power supply. Count
the time that the led strip lights and in case of
less time than the minimum autonomous
duration the battery must be replaced. If the
measured time is considerably less than the
minimum autonomous duration
In case of battery or led strip
replacement, these must be replaced by parts
of the same type, by the manufacturer or by a
competent person.
t i
in battery recycling
points. Do not incinerate.
If the
luminaire doesn’t work as described above
contact the installer.
contact the
installer.
5. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
6. I s not allowed to discard batteries in to
common trash bins, they must be
discarded only
TECHNICAL CHARACTERISTICS
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (230V AC / emergency)
ILLUMINATION SOURCE
1.5 h 3 h
24 h
Battery charge indication LEDs, TEST button
IP 20
12 white LED’s
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
5 to 40 C
o
Up to 95%
Bayblend FR3010, transparent polycarbonate
3 years (1 year for the battery)
240 x 90 x 44 mm
345gr.
220-240V AC/50-60Hz
350gr.
High Quality European based Manufacturers
GR-8/leds GR-9/leds
3.6V/0.6Ah 3.6V/1Ah
2.7W / 3VA 3W / 3.5VA
35lm / 85lm 32lm / 85lm
923378005_23_001
Page 1 from 2

923378005_23_001
Page 2 from 2
Figure 1 Diffusor
Reflector
Plastic base Figure 2
Figure 3
Non-maintained
operation
Maintained
operation
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
90: 1.5 hour duration
180: 3 hour duration
(*) Maintained operation: The luminaire lights its
illumination source, when it is powered by the
mains power supply or not.
Non-Maintained operation: The luminaire lights its
illumination source, only in power supply’s
failure.
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Dismantle the device (step 1 of the installation instructions).
2. Disconnect the connector and remove the old battery.
3. Connect the new battery with the same type (step 4 of the installation instructions) and place it in
the position of the old one.
4. Follow the step 6 of the installation procedure and power the device.
Installation instructions
1. To instal the device you have to dismantle carefully the device with a flat screwdriver as shown in
figure 1.
2. Pass the mains cables thru the hole (point 1 in figure 2). The luminaire must be connected to a
permanent electrical installation to ensure the immobilization of the cable.
3. Mount the base plastic on the wall by using the included mounting accessories in points 2 and 3 in
figure 2.
4. Connect the battery`s cable with the appropriate terminal (figure 3).
5. Connect the mains cables to the terminal block as shown in figure 4.
6. Refit with care the removed plastic parts and power on the luminaire.
NOTE!!
After finishing the installation you must power the luminaire at least for 24 hours for battery
charging to perform the named autonomy.
412
3
Figure 4
For fuse ratings
see text