olympia electronics CLASSIC LIGHT Series User manual

‘’CLASSIC LIGHT’’ SERIES FOR SELF-TESTING MAINTAINED EMERGENCY LUMINAIRES
Bayblend FR3010, transparent polycarbonate
TECHNICAL CHARACTERISTICS
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE 90min
24h
Charge, lamp fault, fault indication LED, TEST button
From overcharge and full discharge
IP 20
150/300lm
6 power LED’s
EN 60598-1, EN 60598-2-22, ΕΝ 61547, EN 55015
0 to 40 C
o
Up to 95%
3 years (1 year for the battery)
580gr.
262 x 100 x 70 mm
Thank you for purchasing this product of
Olympia Electronics. A European manufacturer.
GENERAL o
These luminaires are used indoors (ta 40 C)
where emergency light is needed.
Each luminaire must be permanently connected
to mains power supply.
In normal operation the led strip lights and the
battery is charging. In case of a mains power
supply failure the luminaire will light the led
strip automatically in emergency mode. When
the mains power supply is restored the
device turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 2.
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails and battery has lost its
energy. During this operation the luminaire
enters the idle state and battery consumption is
negligible, in order to be protected from deep
discharge.
Battery charging
The battery charging is completely controled. In
this case, is achieved the perfect battery
maintenance , as well as the elongation of its
duration. When the battery has completely
charged, it charges with a maintenance current.
Manual Test
The manual test can be conducted only if the
main power supply and the battery is connected.
By pressing the test button briefly an operation
test is initiated. During this test period all
indication LEDs are OFF.
Automatic test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the main
power supply and the battery should be
connected.
Automatic Autonomous Test
The Automatic autonomous Test is conducted
and measures the luminaire`s back up operation.
This test is conducted automatically every six
months. In order to be performed, the main
power supply and the battery should be
connected (the battery should be charged). If the
battery is not charged, the test is postponed until
the battery is completely charged. If during the
Automatic Autonomous Test the luminaire’s
duration is lower than the named, then the
battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is stated
in the list of the first page. During emergency
mode, a LED strip test is also performed.
Resetting Errors
Push the Test button for 5 seconds, to extinguish
all the indicated LED errors. Then the luminaire
enters regular operation mode.
Indication LED status (with connected mains
power supply).
AC Charge
On: Good charge current.
Οff: No battery (No charging current or
disconnected battery).
Lamp fault
923119004_09_004
GR-119/6L/42V
35-45V AC
4.5VA
3.6V/1.5Ah
Page 1 from 2
High Quality European based Manufacturers

923119004_09_004
1
Lock - unlock hook
3
Installation instructions
Οn: faulty LED strip.
Off: Good LED strip.
Fault
Οff:Battery OK.
Blink (With AC Charge LED ON): Autonomy or
low battery problem
(the battery must be replaced).
Blink (With AC Charge LED Off):
No charging current or disconnected battery.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only.
2. The device must be connected to the mains
power supply thru a fuse dependent by the total
amount of the line’s power load.
3.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by pulling
out the battery’s connector.
5. I s not allowed to discard batteries in to
common trash bins, they must be
discarded only
In case of battery or lamp replacement, these
must be replaced by parts of the same type, by
the manufacturer or by a competent person.
t i
in battery recycling
points. Do not incinerate.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained
A: Including test device
*90: 90min duration
1 Detach the plastic base (located in the bottom of the luminaire)
by pulling the unlock hook and pass the cables from area or
and through the cable entry hole. Secure it with a suitable
bracket to ensure immobilization of the cable at a distance of
no more than 5cm from the luminaire’s cable entry. Mount the
plastic base with the included mounting accessories.
2 Connect the cables to the terminal blocks as showed in figure.
AC1 for L, AC2 for Ν and L1 for the maintained operation.
The L1 wire can be connected to an external switch to control
the maintained or non maintained operation of the luminaire.
For permanent maintained operation use two wires to power
the luminaire, AC1 for L, AC2 for Ν and link the L and L1.
3 Attach the luminaire by sliding it on the plastic base until the
plastic hook locks, and power the luminaire.
AC1
AC1
AC2
AC2
External
switch
Link
Controled operation of the luminaire
Permanent maintained operation
N
LL1
N
LL1
Page 2 from 2
A
B
Plastic base
2
N
L
A
B
AC1
AC2
L1
Cable entry hole
Cable
support
Battery replacement
It can be done only by a competent person and after the mains interruption.
1. Detach the lamp from its base ( step 1 of the installation procedure ) .
2. Use a flat blade screwdriver to remove the diffusor.
3. Remove the reflector.
4. Disconnect the connector and remove the old battery.
5. Connect the new battery with the same type and place it in
the position of the old one.
6. Replace the removed parts (steps 1,2 and 3).
2