olympia electronics GR-8/leds User manual

GENERAL
o
These luminaires are used indoors (ta 40 C)
on the wall, where emergency light is needed.
Each luminaire must be permanently
connected to mains power supply. In normal
operation the illumination LEDs are lit as well
as the green indicating charge LEDs, when
the battery is charging.
In case of a mains power supply failure the
luminaire will light the led strip automatically
in emergency mode. When the mains power
supply is restored the device turns to normal
operation.
Non Maintained / maintained operation
there is an option to select the non maintained
or maintained operation by placing the jumper
to the appropriate place according to the
figure 3 (see page 2).
INSTALLATION
To install the luminaire follow the installation
instructions on page 2.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
2. The device must be connected to the
mains power supply through a fuse dependent
by the total amount of the line’s power load.
3. It is suggested to check every month the
indication LED for battery charging, and by
pushing the TEST button to check the
emergency circuit. The led strip should light as
long as the TEST button is pressed. If the
luminaire doesn’t work as described above
contact the installer.
4. It is suggested to check every 6 months the
m i n i m u m a u t o n o n o u s d u r a t i o n b y
disconnecting the mains power supply. Count
the time that the led strip lights and in case of
less time than the nominal autonomy, the
battery must be replaced. If the measured time
is c ons i dera bly l ess t han t he no mina l
autonomy In case of contact the installer.
battery or led strip replacement, these must be
replaced by parts of the same type, by the
manufacturer or by a competent person.
5. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
6. I s not allowed to discard batteries in to t i
common trash bins, they must be
discarded only in battery recycling
points. Do not incinerate.
The light source contained in this
luminaire shall only be replaced by the
manufacturer, or his agent, or a similar
qualified person.
NOTE! The light source is non-user
replaceable.
NON MAINTAINED / MAINTAINED EMERGENCY LUMINAIRES
923378005_09_008
Page 1 from 3
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (230V AC / emergency)
ILLUMINATION SOURCE
1.5 h 3 h
24 h
Battery charge indication LEDs, TEST button
IP 42
12 white LEDs
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
o
5 to 40 C
Up to 95%
Bayblend FR3010, transparent polycarbonate
3 years (1 year for the battery)
240 x 90 x 44 mm
345gr.
220-240VAC/50-60Hz
350gr.
GR-8/leds GR-9/leds
3.6V/0.6Ah 3.6V/1Ah
2.7W/3VA 3W/3.5VA
40lm / 100lm 38lm / 100lm
TECHNICAL CHARACTERISTICS (for led module spcifications see page 2)
Thank you for your trust in our products.
Olympia Electronics - European manufacturer.

923378005_09_008923378005_09_008 Page 3 from 3Page 2 from 3
Figure 1 Diffusor
Reflector
Plastic base
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Dismantle the device (step 1 of the installation instructions).
2. Disconnect the connector and remove the old battery.
3. Connect the new battery with the same type (step 4 of the installation instructions) and place it in
the position of the old one.
4. Follow the step 6 of the installation procedure and power the device.
Installation instructions (wall mounting)
1. To install the device you have to dismantle it carefully with a flat screwdriver as shown on figure 1.
2. Pass the mains cables through the hole (point 1 in figure 2) and secure it with a suitable bracket to
ensure immobilization of the cable at a distance of no more than 5cm from the luminaire’s cable
entry. ATTENTION!! To maintain the IP rating, the outer diameter of the power cable must be at
least 8.2 mm².
3. Mount the base plastic on the wall using the included mounting accessories in points 2 and 3 as
shown on figure 2.
4. Connect the battery`s cable with the appropriate terminal (figure 3).
5. Connect the mains cables to the terminal block as shown on figure 4.
6. Refit carefully the removed plastic parts and power on the luminaire.
NOTE!!
After finishing the installation you must power the luminaire at least for 24 hours for battery
charging to perform the nominal autonomy.
Figure 4
For fuse ratings
see text
LED MODULE CHARACTERISTICS
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Olympia Electronics S.A
45 °C max. across the board
Non reversible connection between main pcb and led module
2.9-3.6VDC
780mW
2501159
GR-8/leds GR-9/leds
(*) Maintained operation: The luminaire lights its
illumination source, when it is powered by the mains
power supply or not.
Non Maintained operation: The luminaire lights its
illumination source, only in power supply’s failure.
Note!! The installer should fill in, on the specification label,
the letter G if the luminaire is used as a safety sign.
X19
*0A G
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
G: Internally illuminated
*90: 1.5 hour duration
180: 3 hours duration
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
Figure 2
Figure 3
Non maintained
operation
Maintained
operation
4
12
3
Cable
support