olympia electronics POWER LIGHT Series User manual

GENERAL
These luminaires are used where emergency
light is needed. Each luminaire must be
permanently connected to mains power supply.
In normal operation the power indicator lights
and the charge indicator blinks to show that the
batteries are in charging condition. In case of a
mains power supply failure the power and the
charge indicators turns off and the luminaire
will light the spot lamps automatically in
emergency mode. When the mains power
supply is restored the device turns to normal
operation.
INSTALLATION
To install the luminaire follow the installation
instructions οn page 3.
OPERATION
When the device is powered from the mains, the
charge indicator blinks and confirms the
charging of the batteries. When the batteries
are charged, it lights constantly. If it does not
light, probably, the batteries are disconnected.
If it does not light and the batteries are
connected, then contact the technician. As long
as the charge indicator blinks, the batteries of
the luminaire are charging and in this period,
any autonomy test must be avoided. When the
charging circle is complete, the indicator lights
continuously (it can be used as an indication of a
power interruption). The batteries charging is
done by a 3 stages technological advanced
procedure, to ensure the appropriate and full
charging of the batteries. The power indicator
confirms the proper connection to the mains. The
TEST button, has a dual use. If pressed instantlly
while the device is connected to the mains, the
device simulates the power interruption, by
lighting the lamps for 3''. In this way, we can
control the driver circuit of the lamps and the
lamps as indicated in paragraph 3 in the text
below.
Dimming option
When the voltage is interrup ted,with
corresponding pressings of the button, we can
choose the illumination of 100%, 50%, 33% or
turned off, either to increase the autonomy time
or not to consume the battery power
unnecessarily. This option is canceled when the
network is restored.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
2. The device must be connected to the mains
Page 1 from 3 923029010_09_013
Thank you for your trust in our products
Olympia Electronics - European manufacturer
ABS/PC, PC
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Pb)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
24h
Power indicator, battery charge indicator, TEST button
From overcharge and deep discharge
IP65
5 to 40 C
o
Up to 95%
3 years (1 year for the battery)
180 min
1620lm
White LEDs
3760gr.
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
GRL-29/WP
220-240V AC/50-60Hz
12V/7Ah
14.4W/16VA
307 x 100 x 350 mm
``POWER LIGHT`` SERIES FOR WATERPROOF NON MAINTAINED EMERGENCY LUMINAIRES
TECHNICAL CHARACTERISTICS (for LED MODULE Specifications see page 2)

Page 2 from 3
power supply through a fuse dependent by
the total amount of the line’s power load.
3. It is suggested to check every month the
indication LED for battery charging, and by
pushing instantly the TEST button to check
the emergency circuit and the lamps. If the
luminaire does not light
4. It is suggested to check every 6 months the
minimum autononous duration by
disconnecting the mains power supply.
Count the time that the lamps light and in
case of less time than the minimum
autonomous duration the batteries must be
replaced. If the measured time is
considerably less than the minimum
autonomous duration
The replacement of the battery and the light
source must be done using parts of the
same type, by the manufacturer or by a
competent person.
5.
t i
in battery recycling
points. Do not incinerate.
contact the installer.
contact the installer.
In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
6. I s not allowed to discard batteries in to
common trash bins, they must be
discarded only
Battery replacement
It can be done only by a competent person
and after the mains interruption.
1. Follow the step 2 of the installation
procedure.
2. Disconnect the cables and remove the old
battery.
3. Connect the new battery with the same type
(step 3 of the installation procedure) and
place it in the position of the old one.
4. Follow the step 6 of the installation
procedure and power the device.
923029010_09_013
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non Maintained (*)
A: Including test device
*180: 3 hours duration
(*) Non Maintained operation: The luminaire lights its illumination source, only in power supply’s
failure.
Maintained operation: The luminaire lights its illumination source, when it is powered by the mains
power supply or not.
The light source contained in this luminaire shall only be replaced by the manufacturer, or
his agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
LED MODULE CHARACTERISTICS
Olympia Electronics S.A.
60 °C max. across the board
Cable connection between main pcb and led module
20-25V
5.5W
2002163
Manufacturer
Manufacturer
Voltage Range
Connections
Nominal Power
Temperature (tc)
GRL-29/WP
INDICATION LED STATUS (with the mains power supply connected)
CHARGE POWER
Disconnected battery / not charging
Charged battery Normal operation mode
No mains power supply
Battery under charge
Indicator ON Indicator Blinking Indicator OFF

Page 3 from 3923029010_09_013
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
1. Use the supplied mounting accessories to mount the device (Fig1).
2. Remove the four cover retaining screws (Fig 1).
3. Install the battery cable connectors to the batteries taking care of the polarity, black cable (-)
and red cable (+).
4. Always use in any case round mains cable, with external diameter of 6-9mm (H05RN-F
type 2x1mm² or any other type, at least equal to it’s mechanical and electrical
properties). ATTENTION!! The cable must not be deformed in any way (This
requirement is important to ensure the tightness isolation IP65). Install the cable gland,
pass the round cable through and tighten it all the way.
5. Connect the cables to the respective positions in the terminal block L for phase and N for
neutral.
6. Reinstall the front cover and fasten the retaining screws. (Tightening torque 1Nm).
Pay attention to the 4 sealing o-rings.
WARNING!!
After the installation has finished, charge the batteries for at least 24 hours so as to
obtain the rated autonomous duration.
INSTALLATION PROCEDURE (wall installation only)
TEST
button
Cover
retaining
screws
Fig. 1
Mounting holes
Charge
indicator
Power
indicator
4L
N
3