olympia electronics EASY LIGHT Series User manual

GR-312/15L
220-240V AC/50-60Hz
IP 40
3,6V/1,5Ah
105lm
EN 60598-1, EN 60598-2-22, EN 55015, EN 61547, EN 61000-3-2, EN 61000-3-3
735gr.
3,6V/600mAh
3W /3VA
655gr.
GR-310/15L
Thank you for purchasing this product of
Olympia Electronics. A European manufacturer.
GENERAL
o
These luminaires are used indoors (ta 40 C)
where emergency light is needed.
Each luminaire must be permanently connected
to mains power supply.
In normal operation the battery is charging and
the 2 yellow LED’s light in the screen.
In case of a mains power supply failure the
luminaire will light the led strip automatically in
emergency mode. When the mains power
supply is restored the device turns to normal
operation.
MAINTAINED / NON-MAINTAINED
OPERATION
There is an option to select the maintained or
non-maintained operation by placing the jumper
to the appropriate place according to step 8
(page 4).
INSTALLATION
To install the luminaire follow the installation
instructions οn page 4.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only.
2. The device must be connected to the mains
power supply thru a fuse dependent by the total
amount of the line’s power load.
3. It is sugested to check every month the
indication LED for battery charging, and by
pu s h i n g t h e T ES T b u t to n t o c h e ck t h e
emergency circuit. The led strip should: a) light
with bigger intensity as long as the TEST button
is pressed (maintained operation),
b) light as long as the TEST button is pressed
(non-maintained operation).
4. It is sugested to check every 6 months the
minimum autononous duration by disconnecting
the mains power supply. Count the time that the
led strip lights and in case of less time than the
minimum autonomous duration the battery must
b e r e p l a c e d . I f t h e m e a s u r e d t i m e i s
considerably less than the minimum autonomous
duration In case of battery
or led strip replacement, these must be replaced
by parts of the same type, by the manufacturer
or by a competent person.
t i
in battery recycling
points. Do not incinerate.
If the luminaire
doesn’t work as described above contact the
installer.
contact the installer.
5. In case of inactive use for a period greater
than 2 months, disconnect the battery by pulling
out the battery’s connector.
6. I s not allowed to discard batteries in to
common tr ash bins, t hey must b e
discarded only
TECHNICAL CHARACTERISTICS
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
ILLUMINATION SOURCE
24h
From overcharge and full discharge
15 white LED’s
Bayblend FR3010, transparent polycarbonate
180min
0 to 40 C
o
Up to 95%
3 years (1 year for the battery)
90min
Page 1 from 4
Battery charging LED, TEST button
‘’EASY LIGHT‘’ SERIES FOR NON-MAINTAINED/ΜΑΙΝΤΑΙΝΕD
EMERGENCY LUMINAIRES
350 x 134 x 45 mm (CRV 362 x 134 x 58 mm)
923312017_09_003
High Quality European based Manufacturers

Page 2 from 4 923312017_09_003
Installation methods
A-3018
Special mounting
springs for
suspended ceiling
installation
Mounting springs Α-3018
Wall or ceiling installation Suspended ceiling installation
Wall installation with SP-114
marking panel
A-3018
SP-114 marking panel
Suspended ceiling installation
with Α-3018 mounting springs
and SP-114 marking panel
Recess mounting
base Α-3016
Recess mounting in a wall Ceiling installation
with SP-114 marking panel
MARKING PANEL SP-114
A marking panel SP-114 can be installed on the
luminaire in 3 different locations. This marking
panel is installed perpendicular to the diffusor of
the luminaire, as shown in the pictures below.
The panel is pre-printed and has a plastic
accessory on each side that is used to fasten the
panel to the luminaires.
There are 2 arrow stickers that can be placed in
each side of the marking panel to point to the
desired direction.
Placing the SP-114 marking panel
Place the plastic mounting accessories of the
marking panel as shown in pictures.
ΝΟΤΕ!! This marking panel (SP type) can not
be installed on CRV luminaires.

Page 3 from 4
Suspended ceiling
Α-3018 mounting springs
PLACING Α-CRV PARTS
To install the curve crystal Α-CRV you must first install the
included plastic extension to mount it on the TEST button.
1
2
3
Mounting methods
All “Easy Light” can be mounted either surface or recess
mounted in walls or suspended ceilings. For recess
mounted installations, special accessories are required
which can be found in the catalog and must be ordered
separately.
Suspended ceiling installation.
On the bottom of the base plastic of the Easy light
luminaire there are two H shaped cut outs. These are
used to install the A-3018 mounting springs.
1. With a sharp tool remove the appropriate plastic
pieces to fit the mounting springs. First place the edges
of the mounting spring to the respective holes and install
the one end of the coil to the support axis.
2. Install the other end of the coil to the other support
axis.
3. Bend the springs and place the luminaire to the
respective suspended ceiling’s hole.
The luminaire’s placement to the suspended ceiling
must be done after the connection with power supply
cables.
Recess mounting in a wall
The special mounting base (A-3016) can be built in the
wall and on it can be mounted the luminaire with the Α-
3016 included screws, following the installation
instructions of the luminaire. The mounting base
contains pre-etched holes for cable entry that are
aligned with the cable entry holes of the luminaire.
Bottom view of a wall
Α-3016 recess
mounting base
Mounting Easy Light luminaire
in a suspended ceiling
Recess mounting for an ‘’Easy Light”
luminaire in a wall.
Required
opening in
a suspended
ceiling
340
124
923312017_09_003
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non Maintained (*)
A: Including test device
*90: 1.5 hour duration
180: 3 hour duration
(*) Non-Maintained operation: The luminaire lights its illumination source, only in power supply’s
failure.
Maintained operation: The luminaire lights its illumination source, when it is powered by the mains
power supply or not.

Page 4 from 4
13
INSTALLATION INSTRUCTIONS
B
2
A
Diffusor
Reflector
Base plastic
B
A
923312017_09_003
8. MAINTAINED/NON-MAINTAINED OPERATION
JUMPER SELECTION
You can choose the luminaire’s operation.
When the jumper is installed (by default) on the middle and left
pins you select non-maintained operation. When the
jumper is installed on the middle and right pins you select
maintained operation.
NOTE!! After finishing the installation you must power the
device at least for 24 hours for battery charging to perform the
named autonomy.
5 6
1 To install the luminaire you must dismantle it to 3 parts.
2 Place a flat blade screwdriver in the area Α to release the diffusor’s plastic hook.
3 Place a flat blade screwdriver in the area B to release the reflector’s plastic hook.
4 Use the included mounting parts to mount the base plastic. Pass the mains cable thru a cable
entry channel and secure it with a suitable bracket to ensure immobilization of the cable at a
distance of no more than 5cm from the luminaire’s cable entry.
5 Place the battery’s connector to the corresponding connector on the P.C.B.
6 Connect the mains cables to the respective detachable terminal block. Ν for neutral and L for
live wire.
7 Refit the removed parts in steps 2 and 3 (mind the correct orientation) and the luminaire is ready
to operate.
L
N
Non-maintained
operation
Maintained
operation
Base plastic
Cable entry channels
Luminaire mounting holes
4
Cable
support
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Follow the step 2 and 3 of the installation procedure.
2. Disconnect the connector and remove the old battery.
3. Connect the new battery with the same type (step 5 of the installation procedure) and place it in
the position of the old one.
4. Follow the step 7 of the installation procedure and power the device.