olympia electronics LLB-26/90 User manual

GENERAL
These luminaires are used in places
where emergency luminaires are needed.
Each luminaire must be permanently
connected to mains power supply. In
normal operation the led strip lights and
the battery is charging. In case of a
ma in s p ow er su pp ly fa il ur e t he
lum in a ir e wi ll lig ht t he led st r ip
automatically in emergency mode. When
the mains power supply is restored the
device turns to normal operation.
OPERATION
Battery Charging
The battery charging is completely
controlled by microprocessor and is
protected from completely discharge and
over charge.
Battery Cut-off
The luminaire enters in this operation
when the mains power supply fails and
battery has lost its energy. During this
operation the luminaire enters the idle
state and battery consumption is
negligible, in order to be protected from
deep discharge.
Manual Test
By pressing the test button briefly (less
than 5 seconds) an emergency operation
test is performed. The white LEDs will be lit
for approx. 3 seconds, the red LED will
flash during this test sequence.
Automatic Operational Test
This test includes all the operations that
provide the manual test and is conducted
automatically every 15 days. In order to be
performed, the mains power supply and the
battery should be connected.
Manual Autonomous Test
By pressing the test button for between 5
and 10 seconds a battery condition test is
performed. This test will last for the stated
duration and can only be performed when
the battery is fully charged (steady green
LED). The white LEDs will be lit and the red
LED will flash during this test sequence.
Automatic Autonomous Test
The Automatic Autonomous Test measures
SELF TESTING MAINTAINED EMERGENCY LUMINAIRIES WITH LEDs
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
VIEWING DISTANCE
EXTERNAL DIMENSIONS (LxHxW)
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-MH)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
LIGHT SOURCE INTENSITY (Mains/emerg.)
ILLUMINATION SOURCE
923064003_09_002
220-240V AC/50-60Hz
90 min 90 min 90 min180 min 180 min 180 min
435 x 280 x 55 mm 673 x 400 x 55 mm287 x 205 x 55 mm
4.8V/1.2Ah 4.8V/2.4Ah 4.8V/4Ah 4.8V/2Ah4.8V/1.2Ah
7W/7.4VA (PF=0.94) 9.3W/9.8VA (PF=0.94)6W/6.4VA (PF=0.94)
230lm / 300lm
26m 40m 64m
230lm / 123lm 370lm / 300lm 600lm / 500lm
24 h
Charge LED, Lamp fault LED, Battery Fault LED, TEST button
From overcharge and deep discharge
White LEDs
o
5 to 40 C
Up to 95%
3 years (1 year for the battery)
Aluminum, ABS/PC, PC, Plexiglass
IP 44
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3, EN 1838
1503gr. 1650gr. 2777gr.1396gr.876gr.
TECHNICAL CHARACTERISTICS (for LED MO DULE Specs . s ee page 3)
LLB-26/90 LLB-26/180 LLB-40/180 LLB-64/180 LLB-40/90 LLB-64/90
Thank you for your trust in our products
Olympia Electronics - European manufacturer
Page 1 from 6

the device’s back up operation and
emergency duration. This test is conducted
automatically every 6 months. In order to
be performed, the mains power supply and
the battery should be connected and fully
charged. If the battery is not fully charged,
the test is postponed until the battery is
completely charged. If during this test, the
autonomy is less than the nominal then the
battery fault led will turn on continuously
and the battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the list of the technical
characteristics. During emergency mode, a
light source test is also performed.
Resetting Errors
Push the test button for >10 seconds to
delete all indicated errors. Then the
luminaire enters regular operation mode.
INSTALLATION
To install the luminaire follow the
installation instructions on page 3.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance
or testing must be done by authorized
personnel only.
2. The device must be connected to the
mains power supply through a fuse
dependent by the total amount of the line’s
power load.
3. In case of battery or lamp replacement,
these must be replaced by parts of the
same type, by the manufacturer or by a
competent person.
4. In case of inactive use for a period
greater than 2 months, disconnect the
batte ry by pu ll ing o ut the bat tery’s
connector.
5. I s not allowed to discard batteries t i
into common trash bins, they must
be discarded only in battery
recycling points. Do not incinerate.
The light source contained in this
luminaire shall only be replaced by
the manufacturer, or his agent, or a
similar qualified person.
NOTE! The light source is non-user
replaceable.
Connection to module
This luminary can be connected to any of
the following modules: Remote module,
address module and fault relay module. If
you connect it to a module that supports
inhibit or rest mode, you should know that
these commands can be cancelled only
during normal mode (ie. not in emergency).
You can also refer to the user manual of
each module for additional information. The
picture bellow shows the installation of the
optional module.
GREEN
RED RED
Description
Battery charged no faults
Charging (battery test not possible while charging)
Mains off, battery not connected or charger fault
Battery test
Battery fault
Light source test
Light source fault
Battery fault and light source fault
Off On Flashing
Led status explanation
Indicator LEDs
Page 2 from 6
Picture 1
923064003_09_002

ELECTRICAL CONNECTIONS (after the mains interruption)
1
2
3
4
5
6
7
Unfasten the two side cover screws and remove the plastic
cap by sliding it gently. Install the gasket and make a hole in
the center by using a small screwdriver. Pass the round
cable through the gasket.
Connect the mains cables to the respective terminal block. Ν
for neutral, L for live wire, L1 for the maintained
operation and the for ground connection. The L1 wire
can be connected to an external switch to control the
maintained or non maintained operation of the luminaire.
For permanent maintained operation use two wires to power
the luminaire, Ν for neutral and L for live wire, and link the L
and L1. The A and B contacts are used only if an optional
module is connected.Refer to the modules manual for more
information regarding connection.
The battery is not connected. See the section “Battery
replacement process” to access the battery compartment
and connect the battery.
ATTENTION!! Make sure that the ground cable is attached
to the respective ground connector. Replace the removed
parts in the previous steps.
SURFACE MOUNTING ON A WALL (single sided)
Install the included plastic bracket on the wall (figure 1).
Remove the aluminum bracket from the luminaire and use
the two supplied mounting screws to install the aluminum
bracket to the plastic bracket (figure 2). Slide the luminaire to
the aluminum bracket and use the bolt on the center (*), to
stabilize the luminaire (figure 2).
CEILING MOUNTING (double sided)
Remove the aluminum bracket from the luminaire and install
it with the included spacers, screws and plugs in the ceiling
(page 3). Slide the luminaire to the aluminum bracket and
use the bolt on the center (*), to stabilize the luminaire (figure
4).
Power on the device at the end of the installation.
NOTE!! After finishing the installation you must power
the luminaire at least for 24 hours for battery charging to
perform the nominal autonomy.
INSTALLATION INSTRUCTIONS
(*) First, hand tighten it and then,
use pliers to tighten it little bit
more (not all the way).
LED MODULE CHARACTERISTICS
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Olympia Electronics S.A
45 °C max. across the board 50 °C max. across the board45 °C max. across the board
Non reversible connection between main pcb and led module
14 - 16.5VDC
02041852405185 2605185+2705185
7.2W4.5W 11.7W
LLB-26/90-LLB-26/180 LLB-40/90-LLB-40/180 LLB-64/90-LLB-64/180
Page 3 from 6
N
L
L1
B
A
Ground
connector
2
1
Cable
entry
Screws
L1
L
L1
N
N
L
PE
L1
L
L1
N
N
L
PE
Maintained
operation
(Default)
Non-maintained
operation
Luminaire
terminals
Luminaire
terminals
Connection Diagramms
923064003_09_002

SURFACE MOUNTING ON A WALL (single side luminaire)
CEILING MOUNTING (double side luminaire)
MOUNTING METHODS
Place the included mounting screws
in these holes of the plastic bracket
Mounting screws 1, 3
Included spacers 4
Bolt 2
1
1 3
2
2
4 4
2 Mounting screws
Bolt
Figure 2. Side view
Figure 1
GENERAL!!
Measure the distance of the mounting holes and after
the drilling place on these spots the mounting plugs
and fasten the base with the mounting screws.
Figure 3. Front view
Figure 4
Aluminum
bracket
Plastic
bracket
Page 4 from 6
1
2
SIDE WALL CLEARANCE
Depending on the size
of the luminaire the distance
from the side wall
must be more than:
LLB 26: 440mm
LLB 40: 580mm
LLB 64: 820mm
Luminaire
Aluminium
braket
(a)
(a):
923064003_09_002

Page 5 from 6
FLAG MOUNTED ON A WALL (double side luminaire)
ALTERNATIVE MOUNTING METHODS
A-1135 SET, ONLY FOR LLB-26
(OPTIONAL AFTER REQUEST)
HANGING INSTALLATION (double side luminaire)
A-1136 SET
(OPTIONAL AFTER REQUEST)
INSTALLATION PICTOGRAMMS
1. Unfasten the two screws of the luminaire
and remove the top part of the luminaire.
2.Insert the pictogramm after removing
the protective film from the back side.
3.Carefully fit the top aluminium cover and reinstall the retaining screws.
923064003_09_002

Page 6 from 6
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
Battery replacement process
(*) Maintained operation: The luminaire lights its
illumination source, when it is powered by the
mains power supply or not.
It can be done only by a competent person and after the mains interruption.
1 Unfasten the two side cover screws and remove the plastic cap (with the indications) by sliding
it gently to the right.
2 Remove the old battery. Install the new one and place the connector as shown οn the picture.
3 Refit the plastic cap (with the indications) by sliding it gently to the left and fasten the removed
screws in step 1.
WARNING!! Use a maximum torque of 0,9Νm to tighten the screws.
ΝΟΤΕ!! In case of battery replacement the used battery must be replaced with a new one of
the same type, by the manufacturer or by a competent person.
2
1
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
E: With non-replaceable lamp(s) and/or battery
F: Automatic test gear complying with IEC
61347-2-7 denoted EL-T
G: Internally illuminated
90: 1.5 hour duration
180: 3 hours duration
Note!! If a module will be used (except the fault
relay module), then the installer should fill in, on
the specification label, the letters B C.
X19 0A E F G
923064003_09_002