Omcan MS-IT-0330-C User manual

Revised - 04/26/2018
Toll Free: 1-800-465-0234
Fax: [phone]
Email: [email protected]
www.omcan.com
Gear-Driven Meat Slicer
Model MS-IT-0330-C
Item 38917
Instruction Manual

2
Page
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 5
-------------------------------------------------------------------------- 5
-------------------------------------------------------------------------------------------- 6
----------------------------------------------------------------------------------------- 6 - 7
------------------------------------------------------------------------------------- 7 - 9
---------------------------------------------------------------------------- 10 - 19
---------------------------------------------------------------------------- 20
------------------------------------------------------------------------------------------- 21 - 22
---------------------------------------------------------------------------- 23
Table of Contents
Section
General Information
Safety and Warranty
Technical Specications
Installation
Operation
Maintenance
Parts Breakdown
Electrical Schematics
Notes
Warranty Registration
Model MS-IT-0330-C

3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.

4
General Information
Safety and Warranty
ELECTRICAL SUPPLY
Check that the voltage corresponds to the label data.
1. Connect the machine to the socket.
2. Check that the blade cover fastener handle is tight screwed.
3. Check that the blade sharpener is lowered and the protective cover is closed.
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre leer y familiarizarse con todas las instrucciones de
operación y seguridad.
Omcan quisiera darles las gracias por la compra de esta máquina. Es de la máxima importancia para
guardar estas instrucciones para referencias en el futuro. También guarde la caja original y el embalaje
para envío del equipo si el mantenimiento o la devolución de la máquina es necesaria.

5
Safety and Warranty
Technical Specications
4. Press the green pushbutton to start the blade rotation (pilot light on).
5. The blade must rotate in the counterclockwise direction.
1 YEAR PARTS AND LABOR BENCH WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop off to either
an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the
equipment.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see www.omcan.com/warranty.html for complete info.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
Model MS-IT-0330-C
Blade 13” / 330mm
Power 350W / 0.47 HP
Slicing Capacity (○ 9.45”) □ 10.6” x 6.7” / (○ 240mm) □ 269 x 170mm
Cut Thickness 0 - 0.55” / 0 -14mm
Drive Gear
IP 65
RPM 240
Electrical 120V / 60Hz / 1
Weight 94.8 lbs. / 43 kgs.
Packaging Weight 110 lbs. / 50 kgs.
Packaging Dimensions 32.7” x 28” x 26.7” / 831 x 711 x 678mm
Item Number 38917

6
Installation
Operation
The slicer must be placed on a plane, horizontal, anti-skid and stable surface, t for carrying its weight. The
recommended height of the work top is about 800 mm. Check there are no obstacles for the product holder
stroke.
PRELIMINARY CLEANING
Clean off the protective oil from the slicer.
WARNING
The following products are not sliceable:
• Inedible products.
• Products with bones.
• Frozen products.
Check that the slicer is off and position the slice thickness control on zero.
HOW TO LOAD THE PRODUCT TO CUT
1. Place the product to cut against the product holder and the thickness plate sides.
2. Lay the last slice device on the product to cut, far from the slice thickness plate. The product is fed to the
slice thickness plate by gravity, this makes the cut easier.
3. Rotate the slice thickness control onto the cutting thickness you wish.
4. Press the green pushbutton to start the blade.
5. At constant speed feed the product holder to the blade stroke end then return to the operator and repeat
the operation.
6. When the work is over, pull the product holder towards the operator, press the red button to turn the blade
off and rotate the slice thickness control on zero.
HOW TO LOAD SHORT PRODUCTS (LAST SLICE)
Check that the slicer is off and position the slice thickness control on zero.
WARNING: Do not use your hands to push the products towards the blade.
1. Place the product to be cut against the wall of the product holder and the slice thickness plate.
2. Push the goods against the slice thickness plate using the last slice device.
3. Rotate the slice thickness control onto the cutting thickness you wish.
4. Press the green pushbutton to start the blade.
5. At constant speed feed the product holder to the blade stroke end then return to the operator and repeat
the operation.
6. When the work is over, pull the product holder towards the operator, press the red button to turn the blade

7
Operation
Maintenance
off and rotate the slice thickness control on zero.
BLADE SHARPENING
Whenever the cut is not satisfactory, sharp the blade. The time interval between a sharpening and the following
depends on the intensity of use of the slicer and on the kind of food you cut. Replace the blade when the
diameter becomes 10 mm less than the nominal diameter. For the replacement, ask the assistant service
closest to you.
WARNING
The replacement of the blade is dangerous operation. Should the sharpening quality be not satisfactory,
replace the stones. Contact a customer servicing.
1. Clean the blade removing any greasy residue.
2. Make sure that the machine is off.
3. Rotate the slice thickness control to zero to make sure that the blade is covered by the slice thickness
plate.
4. Lift the sharpener cover.
5. Slip off completely the sharpener and spin it 180 degrees.
6. Put the sharpener device.
7. Push the green button to start the machine.
8. Sharpening: Press the sharpening wheel for about 10-15 seconds. Then press simultaneously also the
grinding stone for two seconds. Contemporaneously loosen the two grind stones. The sharpening and
honing take place then simultaneously.
WARNING: for a suitable effect please execute sharpening for 10-15” approx.
9. Press the red stop pushbutton.
10. Lift and rotate 180 degrees the sharpener and reallocate it into its initial position. Loosen the handle
rotating it clockwise to block the sharpener. Lower the sharpener cover.
SHARPENER DEVICE REMOVAL
To facilitate the cleaning of the sharpening grinder, remove the sharpener device pulling it upwards.
WARNING: Do not immerse in water or detergent the sharpening device.
CLEANING OF THE GRINDING WHEELS
To obtain an excellent sharpening the grinding wheel must always be clean. Remove dirt and grease with
alcohol and the supplied special brush.

8
Maintenance
MAINTENANCE
Disconnect the plug from the power point and take the slice thickness control on zero. We advise to wear
protective gloves during all the cleaning and maintenance operations.
ELECTRIC CABLE CHECK
Periodically check the electric cable wear.
SPARE PARTS
In case of parts replacement, ask only original spare parts.
CLEANING
If you do not use the machine for long time, always carry out a deep cleaning of the machine before using it.
For the cleaning of all the open parts use a dampen cloth.
WARNING: Do not use water jet.
COMPONENTS REMOVAL
DANGER: During the cleaning operations be careful: danger of accident.
PRODUCT HOLDER
1. Position on zero the slice thickness control.
2. Loosen up completely the product holder clamping handle rotating it counterclockwise.
3. Pull the product holder towards the operator to block it. The metallic click means that the product holder is
clamped.
4. Lift the pusher from the guide bar.
5. Lift the product holder slipping it off from its support.
6. Clean the product holder.
IMPORTANT: The slice thickness control is clamped on zero.
SLICE DEFLECTOR
1. Loosen the xing screws and remove the slice deector.
BLADE COVER
1. Loosen the blade cover fastener handle rotating it counterclockwise.
2. Push the handle in the direction of the blade.
3. Lift the blade cover.
ATTENTION: Once removed the blade cover, an interlocking device stops the rotation of the blade.

9
Maintenance
BLADE CLEANING
DANGER: During the cleaning of the blade, be careful of any accidental contact with the blade.
1. Mop up the front side of the blade with a dampen cloth and move slowly from the centre to the edge of the
blade, as shown by the arrow in the picture.
2. Clean in the same way the back side of the blade.
3. Dry with a cloth both sides of the blade.
4. After cleaning, x the blade cover.
5. Insert the fastener and screw to block the blade cover.
Clean all the pieces in warm water and washing-up liquid. Rinse them with hot water and dry them. Assemble
the machine following in reverse the procedure described above.
GUIDES LUBRICATION
This operation must be performed after cleaning the slicer or whenever the sliding is difcult. Use oil SHELL
ONDINA 15 or ESSO MARCOL 82.
LUBRICATION OF THE GUIDE BAR OF THE PRODUCT HOLDER:
1. Drop some oil on the bar.
2. Let the last slice device slide on the guide bar.
LUBRICATION OF THE GUIDE BAR OF THE PRODUCT HOLDER CARRIAGE:
1. Push the product holder towards stroke end.
2. Lift the slicer.
3. Drop some oil on the bar.
4. Place the slicer on the work top, push the product holder to and from.
REFERENCE
Item Number Model Number Description Manufacturer Model
Number
38917 MS-IT-0330-C
Meat Slicer Gear Driven 13” / 330mm
Blade 0.5 HP / 350W 120V/60/1
NSF ETL CSST
C 33F/N

10
Parts Breakdown
Model MS-IT-0330-C 38917

11
Parts Breakdown
Model MS-IT-0330-C 38917

12
Parts Breakdown
Model MS-IT-0330-C 38917

13
Parts Breakdown
Model MS-IT-0330-C 38917

14
Parts Breakdown
Model MS-IT-0330-C 38917

15
Parts Breakdown
Model MS-IT-0330-C 38917

16
Parts Breakdown
Model MS-IT-0330-C 38917

17
Parts Breakdown
Item No. Description Position Item No. Description Position Item No. Description Position
36535 Assembly Sharpener for C 33F/N A1036 36576 Bushing DU 28x32x25 for C 33F/N B6335 36647 Nut U5588 M8 for C 33F/N D0165
17279 Ring EL.Benzing 5 for C 33F/N A5403 78677 Bushing Fastener Guard Knife C for C
33F/N B6398 36648 Nut U5588 M8 for C 33F/N D0165X
16902 Ring EL.Benzing 8 for C 33F/N A5406 36584 All Sharpener Cover for C 33F/N C1637 36653 Spacer for C 33F/N D5413
17281 Ring EL.Seeger Ext.25 for C 33F/N A5453 36593 Assembled Carriage for C 33F/N C1903 36654 Spacer for Register M10 p.1x33 for
C 33F/N D5457
77585 Ring EL.Seeger Est.25 Ser.Heavy for
C 33F/N A5454 65610 Cord 0.5 lg.750 Cover Blade Microswitch for C 33F/N C3351 65614 Spacer Fixing Sharpener Cover for C 33F/N D5472
77586 Ring EL.Seeger Int.52 for C 33F/N A5485 17316 Pin 8.5mm for C 33F/N C4601 65615 Foot Spacer Ø8x22x25 Front Left for
C 33F/N D5495
19612 Ring 33 for C 33F/N A5495 17317 Pin .11 for C 33F/N C4602 65616 Foot Spacer Ø8x22x17 Front Right for
C 33F/N D5496
17283 Oil Seal 25x52x10 for C 33F/N A5809 36601 Rivet 1.9x5 for C 33F/N C4640 65617 Foot Spacer Ø8x22x20 Back Left for
C 33F/N D5497
17285 Oil Seal 60x75x8 for C 33F/N A5815 36607 Blade Cover Bolt Keeper 14x14 for C
33F/N C5007 65618 Foot Spacer Ø8x22x20 Back Right for C 33F/N D5498
19493 Oil Seal 25x47x07 for C 33F/N A5816 65148 Condenser 20 MF 250 VAC-UL for C
33F/N C5815 36659 Hand Grip-Knob Spacer for C 33F/N D575081
17288 O-Ring 3081 20.24x2.62 for C 33F/N A5854 74403 Connector Faston 2Poles Male for C
33F/N C6010 36661 Carriage Shock Absorber Spacer for C 33F/N D5762
65609 Sealing Ring Shaft for C 33F/N A594601 65611 Cover for Box S1033 Latamid for C 33F/N C644880 60786 Locknut Spacer for C 33F/N D5770
36544 Carriage Rod for C 33F/N B1010A 78266 Motor for C 33F/N C6463 17345 Cam Bearing for C 33F/N E1458
60431 Complete Carriage Rail Assembly for
C 33F/N B1080 36615 Back Motor Cover for C 33F/N C6466 79267 Cam Eccentric Stroke mm.16 for C 33F/N E1489
36549 Shock Absorber Rod 12x185 for C 33F/N B1252 36616 Transparent Cover for Carr. Plate for
C 33F/N C6538 36680 Carriage Felt for C 33F/N F1606
19501 Meat Grip Rod A310 & C for C 33F/N B1337A 36617 Motor Fan Cover for C 33F/N C6573 36682 Unhook Friction Clasp 12x22x8 for C
33F/N F3015
65883 Sliding Bar for C 33F/N B1736 36623 Foot Cover for C 33F/N C6682 77591 Support Blade Flange for C 33F/N F6039
17298 Bushing Fastener C for C 33F/N B6006 65612 Sharpener Body for C 33F/N C680764 65619 Flange x Index Knob I2131 for C 33F/N F6088
19618 Bushing 8x10x8 for C 33F/N B6009 36628 Switch Cover 16x20 for C 33F/N C7113 17351 Locknut for C 33F/N G5018
16904 Bushing Sharpener for C 33F/N B6048 17334 Bearing 2Z-6205 25x52x15 for C 33F/N C8011 36689 Stainless Steel Locknut M8 for C 33F/N G5027
16905 Bushing DU 16x18x15 for C 33F/N B6053 16925 Bearing 2RS-6204 20x47x14 for C 33F/N C8024 36691 Ring for Bushing for C 33F/N G5053
17304 Bushing for C 33F/N B6056 36630 Bearing 5x16x6.5 for C 33F/N C8035 36692 Ring for Cam for C 33F/N G5054
19630 Bushing Fastener HBC for C 33F/N B6104B 36631 Bearing 2RS-6205 25x52x15 for C 33F/N C8056 36695 Ring Support Cap for C 33F/N G5055
78265 Bushing, Funnel for C 33F/N B6110 16926 Bearing 2RS-6000 (10x26x8) for C 33F/N C8067 36697 Logging Lock Nut for C 33F/N G5064
18648 Bushing for C 33F/N B6212 78293 Nut U5589 M8 for C 33F/N D0135 36698 Index Ring M10 p.1 h.17 for C 33F/N G5084
36563 Carriage Bushing for C 33F/N B6213 36637 Nut U5589 M8 Stainless Steel for C
33F/N D0135X 36700 Seal for C 33F/N G8014
36564 Bushing for Carriage Support lg.23mm
for C 33F/N B6214 77505 Stainless Steel Nut U5588 M12 for C 33F/N D014215 17354 Handle T210 for C 33F/N I1910
36566 Bushing to hold Carriage Springs for
C 33F/N B6221 77555 Domed Nut DIN 917 M8 Stainless Steel for C 33F/N D014515 17356 Fastener Handle for C 33F/N I1926
36569 Fixing Lever Bushing for C 33F/N B6239 19643 Nut M10 for C 33F/N D0157X 18220 Handle Carriage for C 33F/N I203576
36570 Bushing DU 16x18x20 for C 33F/N B6246 36643 Nut U5588 M5 for C 33F/N D0160 17363 End Grip Handle for C 33F/N I2040
36574 Bushing for C 33F/N B6333 65613 Stainless Steel Nut U5588 M4 for C
33F/N D016115 65620 Handle 28x170 Carriage Tray NSF for C 33F/N I205577
36575 Bushing for C 33F/N B6334 19644 Nut M6 for C 33F/N D0163 63463 Transparent Cover Knob Screw for C
33F/N I2090
Model MS-IT-0330-C 38917

18
Parts Breakdown
Item No. Description Position Item No. Description Position Item No. Description Position
36717 Knob Assembly for C 33F/N I2098 16955 Shock Absorber for C 33F/N P1059 65640 Oil Receiver for C 33F/N R1027
36719 Cover Handle for C 33F/N I2102 17395 Shock Absorber for C 33F/N P1081 19657 Washer 4 for C 33F/N R6003
23632 Screw for C 33F/N I2103 36763 Slice Deector for C 33F/N P1147 19659 Washer 8 for C 33F/N R6006
65621 Knob Ø12x25 M6 for C 33F/N I2115 36767 Knife Guard with Cover Handle for C
33F/N P155021 36877 Washer 8.2x16x0.9 for C 33F/N R6207
65622 Sharpener Body Knob for C 33F/N I2117 36773 Ring Guard for C 33F/N P1666 78258 Washer 30.5x46.5x0.6 for C 33F/N R6251
65623 Impugnatura Ass.Piatto serie NSF for
C 33F/N I2182 77617 Strain Relief for C 33F/N P2009 19666 Washer for C 33F/N R6280
65624 Impugn.Graduata Ass. for C 33F/N I2184 74413 Cable Sheath Cavoex CM 60 for C
33F/N P2011 36881 Washer U6593 5 (5.5x15x1.2) for C 33F/N R6507
16936 Bronze Gear 328 DP56.44 Z29 M1.75
for C 33F/N I2403 36778 Wire-Press for C 33F/N P2014 20422 Washer for C 33F/N R6509
65655 Gear PK z.29 for C 33F/N I2413 36779 Core-Hitch + Nut for C 33F/N P2015 17457 Washer U6592 6 Stainless Steel for
C 33F/N R6512X
62350 Bushing Glide Dia 8x8 for C 33F/N I3065 17419 Pin Truing for C 33F/N P322601 36884 Washer U6592 8 Stainless Steel for
C 33F/N R6520X
62351 Bushing Glide Pin Dia 8x38 for C 33F/N I3082 36793 Pin.Handle for C 33F/N P3430 36885 Washer U6592 10 Stainless Steel for
C 33F/N R6530X
72282 Overload Protector for C 33F/N I3697 36794 Carr. Plate Lock Pivot for C 33F/N P3440 17458 Contact Washer for C 33F/N R6806
65625 Blade mm.330/57/4 Øint.286 for C 33F/N L0632 65628 Pivot Sharpener for C 33F/N P3647 36889 Washer 10.5x16x1 for C 33F/N R6816
65626 Assy Lift Lever for C 33F/N L2498 79272 Knife Shaft for C 33F/N P3648 17460 Washer 34.2x46x0.5 for C 33F/N R6846
14787 Grinding Stone C for C 33F/N M6602 36805 Pivot for Grinding Stone (A1036) for C
33F/N P3657 77595 Washer 44,5x51,5x0,2 for C 33F/N R6848
36739 Honing-Finishing Stone for C 33F/N M6621 77594 Assembly Driving Pivot for C 33F/N P3697 77540 Washer 6,2x14x0,6 for C 33F/N R6854
19776 Spring 14x1.5x60 for C 33F/N M7032 65629 Concave Start Button Pin for C 33F/N P3701 19675 Washer C for C 33F/N R6863
19782 Spring 19.5x1.5x16.7 for C 33F/N M7050 65630 Convex Stop Button Pin for C 33F/N P3702 36892 Washer 17x30x4 for C 33F/N R6874
19250 Spring 24.8x1.8x15 for C 33F/N M7071 36830 Flat Bar C for C 33F/N P4765 16972 Washer 5.5x19x2.5 for C 33F/N R6884
36746 Spring 7x0.8x23 Cam for C 33F/N M7076 36834 Index Casting C-H for C 33F/N P4860 36893 Stainless Steel Special Washer 8.5x24x2
for C 33F/N R6897X
19248 Spring 15.6x20x2.2 for C 33F/N M7120 65631 Piattina Fermo Corpo Aflatoio for C
33F/N P4937 36897 Special Washer 5.5x22x1.5 for C 33F/N R6932
36749 Carriage Bar Spring 25-28-1.5 for C
33F/N M7121 17438 Foot for C 33F/N P5030 65641 SPECIAL WASHER x SHARPENER 6x25x1 R6959
36750 18.5x20.9x1.2 Bar Carriage Spring for
C 33F/N M7122 65632 Sliding Bearing Flat for C 33F/N P5102 61390 Thickness Dial Plate for C 33F/N R6966
36751 Spring for C 33F/N M7166 65633 Piattina Supp.Cerniera C for C 33F/N P5112 78261 Rotor Stator H.50 for C 33F/N R8021
65627 Button Spring for C 33F/N M7182 65634 Piattina for Cerniera for C 33F/N P5114 65642 P.C.B. Protection Box for C 33F/N S103380
20263 Motor 120V/60Hz-1 for C 33F/N M8246 65635 Carriage Product Tray for C 33F/N P5333 19680 Ball 3 17 for C 33F/N S3005
65205 Oiler Bar Cart H / L-C-M-GF for C 33F/N O4040 65636 Assy Carriage Tray for C 33F/N P5678 17465 Ball 4.76 for C 33F/N S3015
36759 Rubber Shock Absorber 12x19x2 for
C 33F/N P1012 78235 End Grip for C 33F/N P6729 36906 Circuit Board 120V/60 OPT.148 for C 33F/N S3284
17390 Rubber Shock Abs. 16x22x2.5 for C
33F/N P1019 36850 Assembly End-Grip for C 33F/N P7019 36908 Track C-CD for C 33F/N S3815
36760 Pin Tray Shock-Absorber for C 33F/N P1025 65637 Special Screw M6x25 x Knob for C 33F/N P7475 36910 LED KL74D250 for C 33F/N S6506
17392 PL.Shock Absorb.8.5x20 for C 33F/N P1034 65638 Special Screw Captive M8x44 for C
33F/N P7478 36915 Pin Stainless Steel D.6x28 for C 33F/N S7516
36761 Shock Absorber for C 33F/N P103401 36857 Upper Blade Protection for C 33F/N P7969 36920 Pin 4x25 for C 33F/N S7526
19797 Nylon Shock 8.5x8 for C 33F/N P1042 17448 Sharpener Pusher for C 33F/N P8601 36921 Stainless Steel 4x7 Pin M.C for C 33F/N S7527
36762 Rubber Plug for C 33F/N P1053 65639 Assy On/Off Switch + PCB for C 33F/N P9507 36931 Pin 8x50 for C 33F/N S7669
Model MS-IT-0330-C 38917

19
Parts Breakdown
Item No. Description Position Item No. Description Position Item No. Description Position
19870 Stator 120/60 for C 33F/N S8562 37018 Screw STTC U6113 M6x6 for C 33F/N V6010 65653 Stainless Steel Screw TE U5739 M6x12
for C 33F/N V6414X
65643 Capacitor Holder for C 33F/N S8866 37019 Screw M5x20 U5923 for C 33F/N V6027 37064 Screw TE U5739 M10x35 for C 33F/N V6415X
78236 Bracket Washer C for C 33F/N S8951A 65651 Vite STEI U5923 M8x40 INOX for C
33F/N V6040 37066 Screw TE U5737 M6x15 for C 33F/N V6421
65644 Bracket Support for C 33F/N S919201 60426 Stainless Steel Screw STEI U5923
M8x60 for C 33F/N V6041 37067 Screw TE U5739 M5x20 for C 33F/N V6423
36974 Carriage Plexi Support for C 33F/N S9238 65652 Vite STEI U5923 M10x40 INOX for C
33F/N V604715 17497 Screw TSP U6109 M5x15 Stainless Steel for C 33F/N V7014X
36976 Support for C 33F/N S9402 37023 Screw STEI U5929 M5x5 for C 33F/N V6065 17498 Screw TSPEI U5933 M4x10 for C 33F/N V7043
36977 Sharpener Support for C 33F/N S9448 19691 Grub Screw M6x6 for C 33F/N V6066 65654 Stainless Steel Screw U6110 M10x30
for C 33F/N V706915
36978 Support Bracket for C 33F/N S9451 19692 Screw M6x8 for C 33F/N V6067 37088 Screw TSP AUT.U6952 4.2x16 INOX
for C 33F/N V708015
65645 Holder Blade Guard for C 33F/N S9452 37025 Screw STEI U5929 M6x8 for C 33F/N V6067X 17502 Screw M3x5.5 for C 33F/N V7901
65646 Bracket Tray for C 33F/N S9496 19695 Screw M10x30 for C 33F/N V6080 17503 Screw M5x13 for C 33F/N V7908
65647 Assy Carriage Tray Holder for C 33F/N S9634 37030 Screw M12x16 U5927 for C 33F/N V6081 19717 Screw M6x50 for C 33F/N V7917
19878 Rubber Cap for C 33F/N T1002 37031 Screw STEI U5929 M8x16 for C 33F/N V6083 19720 Screw M6 for C 33F/N V7934
19883 Label Oil for C 33F/N T1690 19697 Screw M5x16 for C 33F/N V6211 19917 Screw BS for C 33F/N V7960
65648 Slices Counter Label OPT3 for C 33F/N T1776 19699 Screw M4x25 for C 33F/N V6231 16987 Special Screw M6x15 for C 33F/N V8020
65649 Blade Cover Fastener M8x312 for C
33F/N T5146 19700 Screw M6x16 for C 33F/N V6240 37102 Screw M6x20 for C 33F/N V8035
44014 Knife Cover Tie Rod (Release Knob) for
C 33F/N T5182 19702 Screw M6x25 for C 33F/N V6246 19920 Screw M8x30 for C 33F/N V8036
36997 Knife Shaft Assembly for C 33F/N T8092 37039 Screw TCEI U5931 M6x25 INOX for
C 33F/N V6246X 37104 Threaded Stud for C 33F/N V8042
36999 Riding Pin (Diam.28) for C 33F/N T8538 37042 Screw TCEI U5931 M8x25 for C 33F/N V6254 37108 Special Fixed End Screw M6x17 for
C 33F/N V8056
79283 Shaft Pin for C 33F/N T9742 77630 Stainless Steel Screw TCEI U5931
M4x12 for C 33F/N V634415 19726 Screw M5x21 for C 33F/N V8059
65650 Aluminum Gauge-Plate for C 33F/N V313605 37056 Stainless Steel Screw M6x12 U5931 for
C 33F/N V634515 37113 Screw for Carr. Index M8x25 for C 33F/N V8099
37013 Motor Fan MEC80 148x16 for C 33F/N V4014 37058 Stainless Steel Screw M4x8 for C 33F/N V6370 65884 Sliding Bar Screw M14 p.1x13 ch17 for
C 33F/N V8115
37014 STEI Screw 6x20 for C 33F/N V6001 37059 Stainless Steel Screw M4x14 for C 33F/N V6371 37114 Stainless Steel Screw M6x25 for C
33F/N V8130
37016 Screw STTC U6113 M4x25 for C 33F/N V6008 37060 Stainless Steel Screw TE U5737 M5x12
for C 33F/N V6403X
Model MS-IT-0330-C 38917

20
Electrical Schematics
Model MS-IT-0330-C 38917