Omega ECHO TOUCH Quick start guide

Table Of Contents - :~~~t,~
"",,$, "
Installing &Programming The ECHO System 3
Overview
Of The Controller 4
The ECHO-TOUCH Status Screen 5
Using The
ECHO-TOUCH Controller 6
First time use &controller setup 6
Language selection 6
Controlling
your system 7
Mutli-Car Operation &Vehicle Profiles 12
Multi-car operation 12
Programming the vehicle
name 12
Selecting car1
or car2 13
Selecting the vehicle image 13
Programming
The Controller Options 14
Selecting button beep, melody, &vibrate modes 14
Clock &time options
overview 15
Setting the time &date 15
Setting the time format (12
or 24 Hour) 16
Setting the alarm clock 16
Demo mode 17
LCD screen display options
overview 17
Setting the screen on time 18
Setting the screen brightness 18
Other Controller Functions 18
Viewing the alarm trigger history 18
Power off mode 19
•Parking timer &remote start timer. 19

The ECHO-TOUCH communicates with awindow-mounted base unit which
is plugged directly into the host security system module. The window-mount
antenna should
be mounted directly to the interior glass by utilizing the attached
adhesive pad (clean the glass before adhering) for the best performance. The
receiver/transmitter also contains alternative Status Lights and aValet Switch.
these may
be used, or the original items may be retained.
NOTE: It is recommended to fully charge the controller before use.
•
Host Omega Security
System Control
Module
--~
Step 2Plug in and route the Echo
transmitter/receiver unit wiring harness.
Using the adhesive tape, mount the Echo
transmitter/receiver onto an interior glass
(carefully clean the surface).
-
(configurations vary)
Step 1 \ Echo Base
Locate &Transmitter/
Remove the \Receiver Unit
security system's \
Echo port
jumper \
connector (it has a \
Red wire loop). \
\\\\
{!JJ\
~ Step 3Program the Echo controller and the
\\ original 1-way transmitters into the security system
(see the system's guide for instructions).

Overview Of The Controller '~
1) Antenna: Sends commands to the
system and receives confirmations for
2-way functions,
2) Touch Screen LCD: Displays all
controller function buttons as well as the
status
of your system.
3) Home Button: This wakes up the
controller when the screen is off and
returns you back to the status screen.
4) Charger Port: This
is where you plug
in the charger to recharge the control-
ler's battery.
5) Keychain Loop: Use this loop to
attach the controller to your keychain.
II

·The ECHO·TOUCH Status Screen
,
Alarm Trigger Indicator
In Range Indicator __
Current System State --
Vehicle Image
(Selectable)
Lock/Unlock Indicator_
Vibration Mode Indicato
MelodyNoice Indicator
Battery Level Indicator*
Clock/Timer
Vehicle Name
(Programmable)
Alarm Clock ON icon
CH2/CH3 Indicator
Remote Start ON/OFF Indicator
*The controller is powered by a built-in rechargeable battery. When the battery
level
indicator shows a low battery, plug the supplied USB cable into the control-
ler, then connect the othe end to the supplied AC adapter or your computer's USB
port. While charging, the
indicator will increment from empty to full. When fUll, the
indicator will show a plug icon. II

Using The ECHO·TOUCH Controller :'>
FIRST TIME USE &CONTROLLER SETUP
Before the controller will function properly, it must be matched to the type of
system you have. The ECHO-TOUCH is compatible with many different sys-
tems so please follow these steps to configure it for yours:
1) Press the HOME button to turn on the controller.
2) Tap the screen to see the control icons
3) Press the UP
ARROW once until you see SCREEN
6(pictured to the right).
4) Press the SYSTEM TYPE button
5) Select one of the following options:
Alarm System Only: Use this setting for systems with-
out abuilt-in remote start option.
GEN 1
Remote Start: Use this setting if you press
LOCK+UNLOCK to activate your remote starter.
GEN 2
Remote Start: Use this setting ifyou press the
"III" button or asingle dedicated "START" button to
activate your remote starter.
6) Press the "FOLDER" button to save the setting.
LANGUAGE SELECTION
Go to SCREEN 6and choose: American flag =ENGLISH
•Spanish flag =SPANISH
SCREEN 6

Using The ECHO-TOUCH Controller (cont'd)
CONTROLLING YOUR SYSTEM
SCREEN 1:
To access, press the HOME button and tap the screen.
LOCK: Press and release the "LOCK" icon.
•YOUR SYSTEM SHOULD REACT THE SAME AS
WITH YOUR ORIGINAL CONTROLLER.
•UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, IT WILL PLAY THE LOCK/ARM ANIMATION
AND VOICE ALERT.
NOTE: PRESSING
LOCK TWICE IN 5SECONDS
STARTS THE PARKING TIMER. THE
CLOCK WILL
CHANGE TO 0:00 AND START COUNTING IN MIN-
UTES &HOURS.
UNLOCK: Press and release the "UNLOCK" icon.
•YOUR SYSTEM SHOULD REACT THE SAME AS
WITH YOUR ORIGINAL CONTROLLER.
•UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, IT WILL PLAY THE UNLOCK/DISARM ANIMA-
TION AND VOICE ALERT.
II

Using The ECHO-TOUCH Controller (cont'd)
TRUNK RELEASE /CHANNEL 2: Press the and hold the ''TRUNK'' icon for 3
seconds.
•YOUR SYSTEM SHOULD REACT THE SAME AS
WITH YOUR ORIGINAL CONTROLLER.
•UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, IT WILL PLAY THE
TRUNK RELEASE ANIMA-
TION AND VOICE ALERT
II
START (GEN 1/GEN 2REMOTE START}: Press and release the u*" icon us-
ing the same method as with the original controller (i.e., 1or 2presses, etc).
•YOUR SYSTEM SHOULD REACT THE SAME AS
WITH YOUR ORIGINAL CONTROLLER.
•UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, IT WILL PLAY THE REMOTE START ANIMA-
TION, AND PLAY THE REMOTE START ON/OFF VOICE
ALERT.
•THE CLOCK WILL CHANGE TO 0:00 TO STARTTHE
REMOTE START TIMER. IT WILL TIME
HOW LONG
THE ENGINE RUNS
IN MINUTES &HOURS.

;- Using The ECHO-TOUCH Controller (cont'd)
CHANNEL 3(ALARM ONLY}: Press and release the" *" icon using the same
method as with the original controller (i.e., 1or 2presses, etc).
•YOUR SYSTEM SHOULD REACT THE SAME AS
WITH YOUR ORIGINAL CONTROLLER.
•UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, IT WILL PLAY THE CHANNEL 3ANIMATION
AND VOICE ALERT.
SCREEN 2: To access, press the HOME button, tap the screen, press the down
arrow once.
CHANNEL 3(GEN 1/GEN 2REM START}: Press and release the "CH3" icon
using the same method as with the original controller (i.e., 1or 2presses, etc).
•YOUR SYSTEM SHOULD REACT THE SAME AS
WITH YOUR ORIGINAL CONTROLLER.
•UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, IT WILL PLAY THE CHANNEL 3ANIMATION
AND VOICE ALERT.
II

Using The ECHO-TOUCH Controller (cont'd)
CHANNEL 4(IF EQUIPPED): Press and release the "CH4" icon using the
same method as with your original controller (i.e., 1or 2presses, etc).
•YOUR SYSTEM SHOULD REACT THE SAME AS
WITH YOUR ORIGINAL CONTROLLER.
----.,,-.. NOTE: THE
"CH3" ICON WILL NOT BE VISIBLE
WHEN THE CONTROLLER IS SET FOR
"ALARM
ONLY" UNDER THE "SYSTEM TYPE" SETTING.
CHANNEL 5(IF EQUIPPED): Press and release the "CH5" icon using the
same method as with your original controller (i.e., 1or 2presses, etc).
II
•YOUR SYSTEM SHOULD REACT THE SAME AS
WITH YOUR ORIGINAL CONTROLLER.
NOTE: THE
"CH3" ICON WILL NOT BE VISIBLE
WHEN THE CONTROLLER
IS SET FOR "ALARM
ONLY" UNDER THE "SYSTEM TYPE" SETTING.