Omega DP41-E User manual

12450ML-99 Rev.G MQS1297/0807
Set Default Decimal Point
1. Press MENU. The meter d splays:
2. Press /MIN to d splay the current
dec mal po nt. Change the d splay, f
necessary, to read “FFFFFF.” (Use
/MAX to change the dec mal po nt
pos t on).
3. Press MENU. The meter stores changes ( f appl cable),
then d splays “CNT BY”.
4. Press RESET tw ce. The meter momentar ly d splays
“RESET 2” then returns to the run mode. The meter
w ll now read the nput s gnal (4mA = ≈ 000000.
and 20mA = ≈ 020000.).
Measure and Record Input Values
1. Apply 4mA to the nput and record the
d splay read ng.
INPUT 1 = _________________
Refer to th s as Input One.
2. Apply 20mA to the nput and record the
d splay read ng.
INPUT 2 = _________________
Refer to th s as Input Two.
3. Press MENU unt l the meter d splays:
4. Press MENU unt l the meter d splays:
Press /MIN to d splay “INP6=0”
Change the meter to read “INP.6=1”
(Use /MIN to scroll through d g ts
and /MAX to change the d g t’s value).
5. Press MENU. The meter stores changes and d splays:
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants th s un t to be free of defects n mater als and
workmansh p for a per od of one (1) year from the date of purchase. In add t on to OMEGA’s
standard warranty per od, OMEGA Eng neer ng w ll extend the warranty per od for four (4)
additional years f the warranty card enclosed w th each nstrument s returned to OMEGA.
If the un t malfunct ons, t must be returned to the factory for evaluat on. OMEGA’s Customer
Serv ce Department w ll ssue an Author zed Return (AR) number mmed ately upon phone or
wr tten request. Upon exam nat on by OMEGA, f the un t s found to be defect ve, t w ll be
repa red or replaced at no charge. OMEGA’s WARRANTY does not apply to defects result ng
from any act on of the purchaser, nclud ng but not l m ted to m shandl ng, mproper
nterfac ng, operat on outs de of des gn l m ts, mproper repa r, or unauthor zed mod f cat on.
Th s WARRANTY s VOID f the un t shows ev dence of hav ng been tampered w th or shows
ev dence of hav ng been damaged as a result of excess ve corros on; or current, heat,
mo sture or v brat on; mproper spec f cat on; m sappl cat on; m suse or other operat ng
cond t ons outs de of OMEGA’s control. Components wh ch wear are not warranted, nclud ng
but not l m ted to contact po nts, fuses, and tr acs.
OMEG is pleased to offer suggestions on the use of its various products. However,
OMEG neither assumes responsibility for any omissions or errors nor assumes
liability for any damages that result from the use of its products in accordance with
information provided by OMEG , either verbal or written. OMEG warrants only that
the parts manufactured by it will be as specified and free of defects. OMEG M KES
NO OTHER W RR NTIES OR REPRESENT TIONS OF NY KIND WH TSOEVER,
EXPRESS OR IMPLIED, EXCEPT TH T OF TITLE, ND LL IMPLIED W RR NTIES
INCLUDING NY W RR NTY OF MERCH NT BILITY ND FITNESS FOR
P RTICUL R PURPOSE RE HEREBY DISCL IMED. LIMIT TION OF LI BILITY: The
remedies of purchaser set forth herein are exclusive, and the total liability of OMEG
with respect to this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the purchase price of the
component upon which liability is based. In no event shall OMEG be liable for
consequential, incidental or special damages.
CONDITIONS: Equ pment sold by OMEGA s not ntended to be used, nor shall t be used:
(1) as a “Bas c Component” under 10 CFR 21 (NRC), used n or w th any nuclear nstallat on
or act v ty; or (2) n med cal appl cat ons or used on humans. Should any Product(s) be used
n or w th any nuclear nstallat on or act v ty, med cal appl cat on, used on humans, or m sused
n any way, OMEGA assumes no respons b l ty as set forth n our bas c
WARRANTY/DISCLAIMER language, and, add t onally, purchaser w ll ndemn fy OMEGA and
hold OMEGA harmless from any l ab l ty or damage whatsoever ar s ng out of the use of the
Product(s) n such a manner.
RETURN REQUESTS / INQUIRIES
D rect all warranty and repa r requests/ nqu r es to the OMEGA Customer Serv ce Department.
BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE
DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The ass gned AR number
should then be marked on the outs de of the return package and on any correspondence.
The purchaser s respons ble for sh pp ng charges, fre ght, nsurance and proper packag ng to
prevent breakage n trans t.
FOR W
ARRANTY RETURNS, please have
the follow ng nformat on ava lable BEFORE
contact ng OMEGA:
1. P.O. number under wh ch the product
was PURCHASED,
2. Model and ser al number of the product
under warranty, and
3. Repa r nstruct ons and/or spec f c
problems relat ve to the product.
FOR NON-WARRANTY REPAIRS, consult
OMEGA for current repa r charges. Have the
follow ng nformat on ava lable BEFORE
contact ng OMEGA:
1. P.O. number to cover the COST of the
repa r,
2. Model and ser al number of product, and
3. Repa r nstruct ons and/or spec f c
problems relat ve to the product.
OMEGA’s pol cy s to make runn ng changes, not model changes, whenever an mprovement s
poss ble. Th s affords our customers the latest n technology and eng neer ng.
OMEGA s a reg stered trademark of OMEGA ENGINEERING, INC.
© Copyr ght 2002 OMEGA ENGINEERING, INC. All r ghts reserved.
Th s document may not be cop ed, photocop ed, reproduced, translated, or reduced to any
electron c med um or mach ne-readable form, n whole or n part, w thout pr or wr tten consent
of OMEGA ENGINEERING, INC.
PATENT NOTICE: Th s product s covered by one or more of the follow ng patents: U.S.
Pat. No. Des. 336,895; 5,274,577 / CANADA 2052599; 2052600 / ITALY 1249456;
1250938 / FRANCE BREVET No. 91 12756 / SPAIN 2039150; 2048066 / UK PATENT
No. GB2 249 837; GB2 248 954 / GERMANY DE 41 34398 C2. The “Meter Case Bezel
Des gn” s a trademark of NEWPORT Electron cs, Inc., reg stered n the U.S. USED
UNDER LICENSE. OTHER INTERNATIONAL PATENTS PENDING.
Scale Input Values
1. Press /MIN to d splay “INPUT 1”:
Press /MIN aga n. The meter
d splays “000000”. Enter the INPUT 1
value recorded n step 1 of the Measure
Input Values sect on of th s qu ck start.
2. Press MENU. The meter d splays
“READ 1”:
Press /MIN to d splay a s x-d g t
number. Change the meter to read
“000000”. (Use /MIN to scroll
through d g ts and /MAX to change
the d g t’s value.)
3. Press MENU. The meter d splays
“INPUT 2”:
Press /MIN. The meter d splays
“000000”. Enter the INPUT 2 value
recorded n step 2 of the Measure Input
Values sect on of th s qu ck start.
4. Press MENU. The meter d splays
“READ 2”:
Press /MIN to d splay a s x d g t
number. Change the meter to read
“001000”. (Use /MIN to scroll through
d g ts and /MAX to change the d g t’s value.)
5. Press MENU. The meter stores changes and d splays:
6.
Press /MIN to d splay the current dec mal po nt. Press
/MAX to change the dec mal po nt locat on to “FFFFF.F”.
7. Press MENU. The meter stores th s change, then d splays
“CNT BY”
8. Press RESET tw ce. The meter d splays:
“RESET 2”, then returns to the run
mode. The meter s now scaled to
read 0 to 100.0 for a 4-20 mA nput.
5 6
stored
SETPTS /MAX  /MIN MENU RESET
CNTBY
SETPTS /MAX  /MIN MENU RESET
INPUT1
SETPTS /MAX  /MIN MENU RESET
INPUT2
SETPTS /MAX  /MIN MENU RESET
stored
SETPTS /MAX  /MIN MENU RESET
IN.SC.OF

SETPTS /MAX  /MIN MENU RESET
IN CNF
SETPTS /MAX  /MIN MENU RESET
INp6=0

SETPTS /MAX  /MIN MENU RESET
INPUT2
SETPTS /MAX  /MIN MENU RESET
INPUT1
SETPTS /MAX  /MIN MENU RESET
READ 1
SETPTS /MAX  /MIN MENU RESET
READ 2
SETPTS /MAX  /MIN MENU RESET
stored
SETPTS /MAX  /MIN MENU RESET
CNTBY
SETPTS /MAX  /MIN MENU RESET
stored
SETPTS /MAX  /MIN MENU RESET
Dec pt
SETPTS /MAX  /MIN MENU RESET
REset2
SETPTS /MAX  /MIN MENU RESET
Dec pt
SETPTS /MAX  /MIN MENU RESET
FFFFFF.
SETPTS /MAX  /MIN MENU RESET
TRADEMARK NOTICE:
®
,omega.com
®
,are trademarks of OMEGA
Eng neer ng, Inc.
®
Th s dev ce s marked w th the nternat onal caut on symbol. It s mportant to read the
Setup Gu de before nstall ng or comm ss on ng th s dev ce as t conta ns mportant
nformat on relat ng to safety and EMC.
WARNING: These products are not des gned for use n, and should not be used for, pat ent
connected appl cat ons.
It s the pol cy of OMEGA to comply w th all worldw de safety and EMC/EMI regulat ons that apply.
OMEGA s constantly pursu ng cert f cat on of ts products to the European New Approach
D rect ves.
The nformat on conta ned n th s document s bel eved to be correct, but OMEGA Eng neer ng,
Inc. accepts no l ab l ty for any errors t conta ns, and reserves the r ght to alter spec f cat ons
w thout not ce.
DP41-E
High Performance
Process Indicator
Servicing North merica:
US : One Omega Dr ve, P.O. Box 4047
ISO 9001 Cert f ed Stamford CT 06907-0047
 TEL: [phone] FAX: [phone]
 e-ma l: [email protected]
Canada:7  976 Bergar
 Laval (Quebec) H7L 5A1
 TEL: [phone] FAX: [phone]
 e-ma l: [email protected]
For immediate technical or application assistance:
US and Canada: Sales Serv ce: 1-800-826-6342 / 1-800-TC-OMEGA®
 Customer Serv ce: 1-800-622-2378 / 1-800-622-BEST®
 Eng neer ng Serv ce: 1-800-872-9436 / 1-800-USA-WHEN®
Mexico and  TEL: [phone] FAX: [phone]
Latin merican:e-ma l: [email protected]

Servicing Europe:
Benelux:7 TEL: [phone] FAX: [phone]
 Toll Free n Benelux: 0800 0993344
 e-ma l: [email protected]
Czech Republic: Frystatska 184, 733 01 Karv ná
 TEL: [phone] FAX: [phone]
 e-ma l: [email protected]
OMEG net® On-Line Service
www.omega.com
Internet e-mail
[email protected]
®
®
France: TEL: [phone] FAX: [phone]
 Toll Free n France: 0800 466 342
 e-ma l: [email protected]
Germany/ ustria: Da mlerstrasse 26, D-75392 Deckenpfronn, Germany
 TEL: [phone] FAX: [phone]
 Toll Free n Germany: 0800 639 7678
 e-ma l: [email protected]

Using This Quick Start Manual
Use th s Qu ck Start Manual to get your H gh Performance
Process Ind cator up and runn ng. These nstruct ons use
the factory default sett ngs of current nput and 24 Vdc
sensor exc tat on.
The latest complete Commun cat on and Operat onal
Manual as well as free Software are ava lable at
www.omega.comor on theCD-ROM
enclosed with your shipment.
To start your un t you:
• connect ac power
• w re the sensor
• conf gure the meter, us ng the front panel buttons and the
conf gurat on menus
Before You Begin
Check the ser al label on the top of the meter case. The
model number’s last 3 d g ts nd cate f the meter s set up
for voltage or current. C1 - C2 are current ranges and
DC1 - DC10 are voltage ranges. This quick start manual
uses the C2 (4 - 20m ) range. If your meter s setup for a
range other than C2, consult the Operator’s manual.
In add t on to the un t and related parts, you w ll need the
follow ng tems to set up your un t:
• ac power, as l sted on meter’s Product/ID
• 4-20mA nput (eg: load cell, cal brator)
• 1/8” Ph ll ps head screwdr ver
• 1/8” flat blade screwdr ver
Warning: Do not connect C power to your
device until you have completed all input and
output connections. This device must only be
installed by a specially trained electrician with
corresponding qualifications. Failure to follow all
instructions and warnings may result in injury!
Connect ac Power
1. Remove the rear protect ve cover and set t as de.
The cover s secured w th a Ph ll ps-head screw.
2. Locate connector P1 on the bottom-left-rear of the un t.
The connector has three screw-down term nals.
3. Insert the correct w re n each term nal and t ghten the
lockdown screw. Tug gently on each w re to ver fy the
connect on.
1
2
3
P1
N
~AC LINE
~AC NEUTRAL
PROTECTIVE EARTH GND
L
L
FUSE
N
SWITCH
GREEN WIRE
E RTH
LINE
NEUTR L
Check for proper Earth ground ng
n the power d str but on system (s ngle phase).
Wiring a Current Transmitter
Follow these steps to w re a current nput sensor w th
sensor exc tat on.
1.
Locate connectors P3 & P9 on the r ght-s de-rear of the un t.
2. Attach the w res and t ghten the reta n ng screws. Tug
gently on the w res to ver fy the connect on.
Wiring Example: Current Input with Sensor Excitation
3. Apply ac power. The front panel of the un t flashes RESET2.
If t does not:
a. Remove ac power.
b. Ver fy the P1 power and P3 and P9 nput connect ons.
c. Check your power source.
d. Check your s gnal source.
4.
Replace the rear cover. Thread the sensor w res through
the slots on the s de of the cover. Replace the rear cover
screw.
5. Apply ac power once aga n.
Configure the Meter
Use the front panel buttons to access the conf gurat on
menus, to e ther ver fy or set the un t values. The funct on
of each button s descr bed below:
Meter Button Descriptions
Press Th s Button To:
sequenta lly recall prev ous setpo nt
sett ngs (run mode only), store new
setpo nt values.
access the conf gurat on program
menus and move from one menu
to the next.
enter and scroll through a submenu.
change the value of a submenu.
move backward one menu (press
once) or ex t the conf gurat on
menus (press tw ce).
N/C
+S
–S
P9
1
2
3
1
2
3
P3
N/C
RTN
(+)
(-)
(4-20mA)
+E
–E
JUMPER
USER
PROVIDED
Quick Start Setup
Qu ck Start Setup scales your meter to read 0 to 100.0 for a
4 - 20mA nput. Th s setup procedure s actually a ser es of
short tasks. To complete Qu ck Start Setup successfully, t
s mportant to perform all tasks n the order outl ned n the
Qu ck Start Setup.
Select Input Range
1. Press MENU unt l the meter d splays:
2. Press /MIN unt l the meter flashes:
Press MENU and “CURRNT” stops
flash ng.
Press /MIN to d splay a flash ng
nput range of 4-20mA or 0-20 mA.
Press /MAX unt l the meter d splays
“4-20mA.”
3. Press MENU. The meter stores changes ( f appl cable),
then d splays “RDG.CNF”:
Set Up Reading Configuration
1. Press /MIN to d splay “RDG.1”.
Press /MAX unt l the meter d splays
“RDG.1=0”. Select ng “RDG.1=0”
enables d rect formatt ng.
2. Press /MIN to d splay “RDG.2”.
Press /MAX unt l the meter d splays
“RDG.2=1”. Select ng “RDG.2=1”
enables an act ve dec mal po nt.
3. Press MENU. The meter stores changes ( f appl cable),
then d splays “RDG SC”:
Set Reading Scale Factor and Reading Offset
1. Press /MIN to d splay the scale factor
value. Change the value, f necessary,
to read “1.00000” (Use /MIN to scroll
through d g ts and /MAX to change
the d g t’s value).
2. Press MENU. The meter stores changes ( f appl cable)
then d splays “RDG.OF”:
3. Press /MIN to d splay the offset value.
Change the value, f necessary, to read
“000000” (Use /MIN to scroll
through d g ts and /MAX to change
the d g t’s value).
4. Press MENU. The meter stores change,
f appl cable, then d splays “IN CNF”.
Set Default Input Scale and Offset
1. Press /MIN unt l the meter flashes.
Change the value, f necessary, to read
“INP.6=0” (Use /MIN to scroll
through INP submenu cho ces and
/MAX to select 0 as the value). Sett ng
“INP.6=0” d sables nput scale and offset.
2. Press MENU. The meter stores changes, f appl cable,
then d splays “IN.SC.OF”.
234
START HERE
/MIN
/MAX
RESET
MENU
SETPTS
1.00000
SETPTS /MAX  /MIN MENU RESET
stored
SETPTS /MAX  /MIN MENU RESET
IN.SC.OF

SETPTS /MAX  /MIN MENU RESET
stored
SETPTS /MAX  /MIN MENU RESET
rdg.o
SETPTS /MAX  /MIN MENU RESET
000000
SETPTS /MAX  /MIN MENU RESET
stored
SETPTS /MAX  /MIN MENU RESET
CNTBY
SETPTS /MAX  /MIN MENU RESET
INp.6=0
SETPTS /MAX  /MIN MENU RESET
stored
SETPTS /MAX  /MIN MENU RESET
rdg sc
SETPTS /MAX  /MIN MENU RESET
INPUT
SETPTS /MAX  /MIN MENU RESET
CURRNT
SETPTS /MAX  /MIN MENU RESET
RDG.2=1
SETPTS /MAX  /MIN MENU RESET
stored
SETPTS /MAX  /MIN MENU RESET
rdg.CNF
SETPTS /MAX  /MIN MENU RESET
RDG.1=0
SETPTS /MAX  /MIN MENU RESET