Omega 1151 User manual

I / 20
I / 20
I / 20
E / 21

3
English
Introduction
– Special recommendations ............................. 4
– Environmental protection .............................. 5
– Leather straps ..................................... 6
– Anti-reflective treatment .............................. 6
– Screw-down crown .................................. 6
– OMEGA International Warranty ......................... 7
Operating instructions
–Quartz watch
Calibres: 1376, 1456, 1532, 4061, 4561, 4564 ................ 15
1424, 1538 ................................ 16
–Manual & Self-winding watch
Calibres: 8400, 8401, 8500, 8501, 8507, 8508, 8511, 8601, 8611,
8900, 8901, 8902, 8903, 8912, 8913, 8922, 8923 ........ 17
8602, 8612 ................................ 18
1120, 2300, 2500, 2507, 2520, 2610, 2627, 8520, 8521,
8700, 8701, 8704, 8705, 8800, 8801 ................ 19
2200, 2201, 2202, 2211, 2403, 8421, 8806, 8807 ........... 21
–Manual-winding chronograph
Calibres: 1861, 1863, 1866, 3201, 3203 .................... 22
–Self-winding chronograph with or without date
Calibres: 3202, 3220, 3330 ............................ 24
–Self-winding chronograph with date
Calibres: 1151, 1152, 1164, 3113, 3304, 3313, 3606, 3888, 3890 .... 25
9300, 9301, 9900, 9901 ........................ 27
–Automatic chronograph with moon phase
Calibres: 9904, 9905 ................................ 28
–Self-winding split-seconds chronograph
Calibre: 3612 .................................... 29
–GMT, Worldtimer, GMT Chronograph
Calibres: 2628, 3603, 8605, 8615, 8906, 8938, 8939, 9605, 9615 .... 31
Specific sections/general information
– Chronometer/Master Chronometer ........................ 35
– 15,000 gauss ..................................... 35
– Thermocompensated quartz ............................ 36
– Helium escape valve ................................. 37
– Measurement scales ................................. 39
– Foldover clasps .................................... 41
– Fine length adjustment clasps and diving clasp ............... 43
– Ploprof bezel and crown .............................. 44
– Bullhead crown .................................... 45
– Pictograms ....................................... 46
1
Contents
2
3

4
What must I do to ensure that my OMEGA watch provides
me with excellent service for many years?
Magnetic fields: avoid contact with magnets, or putting your watch
on top of loudspeakers, refrigerators or magnetic cases for iPads or
other tablets, since such objects generate magnetic fields which could
disturb the functions of your watch. Watches that include Master
Co-Axial or Master Chronometer in their name are unaffected by
magnetic fields up to 15,000 gauss (1.5 tesla).
Swimming in the sea: always rinse your watch with fresh water
afterwards.
Shocks: whether physical, thermal or other, avoid them.
Screw-down crown: screw the crown down carefully to prevent
water from penetrating the case.
Non screw-down crown: push it back against the case into the
wearing position to prevent moisture from entering the case.
Cleaning: for metal bracelets, rubber straps and water-resistant cases,
use a toothbrush and soapy water for cleaning and dry with a soft cloth.
Chemical products: avoid direct contact with solvents, detergents,
perfumes, cosmetics, insect repellents, etc., since they may damage
the bracelet, case or gaskets.
Temperature: avoid exposure to extreme temperatures (greater
than 60°C, or 140°F, less than 0°C, or 32°F) or extreme temperature
changes.
Water-resistance: a watch’s water-resistance cannot be permanently
guaranteed. It may notably be affected by the ageing of gaskets or by
an accidental shock to the crown.As stipulated in our service instruc-
tions, we recommend you have the water resistance of your watch
checked once a year by an authorised OMEGA Service Centre.
Chronograph push-pieces: do not operate chronograph pushers
under water in order to prevent water entering the mechanism.
Exception: The Seamaster 300 m and 600 m Chronographs have
pushers which function under water.
Special recommendations
1Introduction

5
English
What are the service intervals?
Like any precision instrument, a watch needs regular servicing to
ensure that it functions perfectly. We cannot indicate the frequency
of such work, since it depends entirely on the model, the climate and
the owner's individual care of the watch. As a general rule, a watch
should be serviced every 4 to 5 years, depending on the conditions
in which it is used.
Who should I contact for a maintenance service or battery
replacement?
We recommend that you contact an approved OMEGA service centre
or authorised OMEGA retailer.They are equipped with the tools and
apparatus required to carry out the work and the necessary checks
in a professional manner. Furthermore, these entities can guarantee
that their work is carried out in accordance with OMEGA’s strict
quality standards.
A worn-out battery should be replaced immediately in order to reduce
the risk of leakage and consequent damage to the movement.The type
of battery is defined on the guarantee card enclosed with your watch.
Special recommendations
Environmental protection
1Introduction
Collection and treatment of end of life Quartz watches*
This symbol indicates that this product should not be
disposed with household waste. It has to be returned to a
local authorised collection system. By following this proce-
dure you will contribute to the protection of the environment
and human health.The recycling of the materials will help to
conserve natural resources.
*valid in EU member states and in any countries with corresponding
legislation.
1Introduction

6
Leather straps
OMEGA recommends that you follow the steps below in order
to preserve the condition of your leather strap for as long as
possible:
– avoid contact with water and dampness to prevent discolouration
and deformation.
– avoid prolonged exposure to sunlight to prevent the colour from
fading.
– do not forget that leather is permeable! Therefore avoid contact
with greasy substances and cosmetic products.
– if you have a problem with your leather strap, please contact your
nearest OMEGA retailer!
Anti-reflective treatment
1
1
Introduction
Introduction
The anti-reflective treatment on both sides of the sapphire crystal
improves the visibility of your watch’s dial. Wear and tear may cause
marks to appear. These are considered normal and are therefore not
covered by the warranty.
Screw-down crown
1Introduction
Some watches are fitted with a screw-down crown which must be
unscrewed to alter the date and time. After use, push the crown into
position 1 then press and screw the crown back down, failure to screw
the crown down will compromise water-resistance.

7
English
OMEGA International Warranty
Introduction1
(Valid for U.S.A. only)
Your OMEGA®watch is warranted by OMEGASA* FOR A
PERIOD OF TWENTY-FOUR (24) MONTHS, THIRTY-SIX (36) MONTHS
FOR WATCHES WITH A CO-AXIAL ESCAPEMENT AND FORTY-EIGHT
(48) MONTHS FOR WATCHES WITH A CO-AXIAL ESCAPEMENT AND
SI14 BALANCE SPRING , AS WELL AS FOR WATCHES WITH THE
CALIBER 8500 OR 8501, FROM THE DATE OF PURCHASE under the
terms and conditions of this warranty. The international OMEGA
warranty covers material and manufacturing defects existing at
the time of delivery of the purchased OMEGA watch (“defects”).
The warranty only comes into force if the warranty certificate is
dated, fully and correctly completed and stamped by an authorised
OMEGA retailer (“valid warranty certificate”).
During the warranty period and by presenting the valid warranty
certificate, you will have the right to have any defect repaired
free of charge. In the event that repairs are unable to restore the
normal conditions of use of your OMEGA watch, OMEGASA
guarantees its replacement by an OMEGA watch of identical or
similar charateristics. The warranty for the replacement watch ends
twenty-four (24) months, thirty-six (36) months for watches with
a co-axial escapement, forty-eight (48) months for watches with a
co-axial escapement and SI14 balance spring , as well as for
watches with the caliber 8500 or 8501, after the date of purchase of
the replaced watch.
This manufacturer’s warranty does not cover:
– the life of the battery.
– normal wear and tear and ageing (for example scratched crystal;
alteration of the colour and/or material of non metallic straps and
chains, such as leather, textile, rubber).
– any damage on any part of the watch resulting from abnormal/
abusive use, lack of care, negligence, accidents (knocks, dents,
crushing, broken crystal, etc.), incorrect use of the watch and non-
observance of the operating instructions provided by OMEGASA.

8
Introduction1OMEGA International Warranty
– the OMEGA watch handled by non-authorized persons (for exam-
ple for battery replacement, service or repair) or which has been
altered in its original condition beyond OMEGASA’s control.
ALL APPLICABLE IMPLIED WARRANTIES, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND OF FITNESS FOR A
PARTICULAR PURPOSE GIVEN TO YOU BY LAW ARE HEREBY LIMITED
IN DURATION TO THE DURATION OF THIS WARRANTY. UNDER NO
CIRCUMSTANCES WILL OMEGASA BE LIABLE FOR ANY INDIRECT
OR CONSEQUENTIAL DAMAGES OF ANY KIND.
Some states do not allow limitations on how long implied warran-
ties last, or exclusions or limitations of incidental or consequential
damages, so exclusions or limitations mentioned may not apply to
you. This warranty gives you specific legal rights and you may also
have other rights which may vary from state to state.
OMEGA SA’s OBLIGATION IS STRICTLY LIMITED TO REPAIR OR
REPLACEMENT AS EXPRESSLY STATED IN THIS LIMITED WARRANTY.
YOURAUTHORISED OMEGA RETAILER CARRIES SOLE RESPONSIBILITY
FOR ANY OTHER GUARANTEES.
The OMEGA customer service ensures the perfect working order
of your OMEGA watch. If your watch needs maintenance, rely on
an authorised OMEGA retailer or an authorized OMEGA Service
Center as set forth on the OMEGA website: they can guarantee
service according to OMEGASA’s standards.
* OMEGASA
Rue Jakob-Stämpfli 96
CH-2500 Bienne 4
OMEGA®and ®are registered trademarks

9
English
OMEGA International Warranty
Introduction
Your OMEGA®watch is warranted by OMEGASA*for a period of
twenty-four (24) months, thirty-six (36) months for watches with a co-
axial escapement and forty-eight (48) months for watches with a co-
axial escapement and SI14 balance spring , as well as for watches
with the caliber 8500 or 8501, from the date of purchase under the
terms and conditions of this warranty.The international OMEGA war-
ranty covers material and manufacturing defects existing at the time of
delivery of the purchased OMEGA watch (“defects”). The warranty
only comes into force if the warranty certificate is dated, fully and
correctly completed and stamped by an authorised OMEGA retailer
(“valid warranty certificate”).
During the warranty period and by presenting the valid warranty
certificate, you will have the right to have any defect repaired free of
charge. In the event that repairs are unable to restore the normal con-
ditions of use of your OMEGA watch, OMEGASA guarantees its
replacement by an OMEGA watch of identical or similar characte-
ristics. The warranty for the replacement watch ends twenty-four (24)
months, thirty-six (36) months for watches with a co-axial escapement,
forty-eight (48) months for watches with a co-axial escapement and
SI14 balance spring , as well as for watches with the caliber 8500
or 8501, after the date of purchase of the replaced watch.
This manufacturer’s warranty does not cover:
– the life of the battery.
– normal wear and tear and ageing (for example scratched crystal;
alteration of the colour and/or material of non metallic straps and
chains, such as leather, textile, rubber).
– any damage on any part of the watch resulting from abnormal/abu-
sive use, lack of care, negligence, accidents (knocks, dents, crushing,
broken crystal, etc.), incorrect use of the watch and non-observance
of the operating instructions provided by OMEGASA.
– any consequential or indirect damage resulting from the use, failure
to operate, defects or lack of precision of the OMEGA watch.
1

10
Introduction
OMEGA International Warranty
– the OMEGA watch handled by non-authorised persons (for exam-
ple for battery replacement, service or repair) or which has been
altered in its original condition beyond OMEGASA’s control.
Any further claim against OMEGASA, for example for damages
additional to the above described warranty is expressly excluded,
except mandatory statutory rights the purchaser may have against
the manufacturer.
The above manufacturer’s warranty:
– is independent of any warranty that may be provided by the
seller, for which he carries sole responsibility;
– does not affect the purchaser’s rights against the seller nor any
other mandatory statutory rights the purchaser may have against
the seller.
The OMEGA customer service ensures the perfect maintenance of
your OMEGA watch.If your watch needs attention, rely on an author-
ised OMEGA retailer or an authorised OMEGA Service Centre as
set forth in the enclosed list: they can guarantee service according to
OMEGASA’s standards.
* OMEGASA
Rue Jakob-Stämpfli 96
CH-2500 Bienne 4
OMEGA®and ®are registered trademarks
1

11
English
OMEGA International Warranty
Introduction
NOTE: If you purchased your OMEGA®watch in Australia or New
Zealand, the International OMEGA®Warranty contained in the
booklet provided with this watch and on the OMEGA®website
(www.omegawatches.com) does NOT apply to you, and is replaced
by this Australian / New Zealand Warranty (referred to below as the
"Warranty").
IMPORTANT NOTICE REGARDING YOUR CONSUMER
RIGHTS
The benefits given to you under this Warranty are additional to, and
do not detract from, other rights and remedies that you may have in
relation to your OMEGA®watch and its purchase underAustralian
or New Zealand laws, including consumer protection laws.
In Australia, OMEGA®watches come with guarantees that can-
not be excluded under the Australian Consumer Law. You are enti-
tled to a replacement or refund for a major failure and compensa-
tion for any other reasonably foreseeable loss or damage. You are
also entitled to have your OMEGA®watch repaired or replaced if
it fails to be of acceptable quality and the failure does not amount
to a major failure.
In New Zealand, OMEGA®watches also come with guarantees that
cannot be excluded under the New Zealand Consumer Guarantees Act.
This Warranty:
– Is not intended to change or exclude any statutory or consumer
rights that cannot be lawfully changed or excluded;
– Is independent of any warranty that may be provided by the seller,
for which he carries sole responsibility; and
– Does not affect your rights against the seller, including any man-
datory statutory rights you may have against the seller under local
consumer laws.
1

12
Introduction
OMEGA International Warranty
OUR WARRANTY TO YOU
ThisWarranty is provided by OMEGASA of Rue Stämpfli 96,CH-2500
Bienne 4, Switzerland. Telephone [phone].
Your OMEGA®watch is covered by this Warranty for the periods set
out below under the terms and conditions of this Warranty.
Watch Warranty Period
OMEGA®watches Two (2) years from the date of
purchase
OMEGA®watches with a co-
axial escapement Three (3) years from the date of
purchase
OMEGA®Co-Axial watches
with a co-axial escapement and
SI14 balance spring and
OMEGA®watches with the
caliber 8500 or 8501
Four (4) years from the date of
purchase
This Warranty covers material and manufacturing defects existing at
the time of delivery of the purchased OMEGA®watch (“defects”).
Where such defects become apparent during the warranty period and
provided you present a valid warranty certificate, OMEGASA will:
– Repair your watch free of charge; or
– In the event that repairs are unable to restore the normal condi-
tions of use of your OMEGA®watch, replace your watch with
an OMEGA®watch of identical or similar characteristics. Such
replacement watch will have the benefit of this Warranty for
the remainder of the Warranty Period applicable to the original
(replaced) watch.
1

13
English
OMEGA International Warranty
Introduction
Please be aware that:
– Goods presented for repair may be replaced by refurbished goods
of the same type rather than being repaired. Refurbished parts may
be used to repair the goods;
– Any data you store in your watch may be lost in the course of
a repair. It is your responsibility to back up any data that may
be stored in your watch before presenting it for warranty service;
and
– The Warranty is only valid if the warranty certificate enclosed with
your OMEGA®watch upon purchase is dated, fully and correctly
completed and stamped and signed by authorised OMEGA®
retailer.
EXCLUSIONS AND LIMITATIONS
This Warranty does not cover:
– The lifetime of the battery;
– Normal wear and tear and aging (e.g. scratched crystal; alteration
of the colour and/or material of non-metallic straps and chains, such
as leather, textile, rubber; peeling of the plating);
– Any damage on any part of the watch resulting from abnormal/abu-
sive use, lack of care, negligence, accidents (knocks, dents, crushing,
broken crystal, etc.), incorrect use of the watch and non-observance
of the use directions provided by OMEGASA;
– Indirect or consequential damages of any kind resulting from e.g.
the use, the non-functioning, the defects or the inaccuracy of the
OMEGA®watch; or
– Defects caused by the OMEGA®watch being handled by non-
authorized persons (e.g. for battery replacement, services or repairs)
or altered in its original condition beyond OMEGASA’s control.
1

14
Introduction
OMEGA International Warranty
HOW TO MAKE A CLAIM UNDER THIS WARRANTY
To make a claim under this Warranty, we recommend that you wrap
your OMEGA®watch carefully so as to avoid any damage and send
it by registered mail or drop it off in person to your nearest authorised
OMEGA®retailer or an official OMEGA®Service Centre. To find
current contact information for your nearest authorised OMEGA®
retailer or official OMEGA®Service Centre, please telephone
[phone], email [e-mail]
or go to www.omegawatches.com.
You will be responsible for paying the expenses associated with
making a claim under this Warranty, including postal or delivery
expenses and any relevant taxes.
OTHER CONDITIONS
No authorised OMEGA®retailer or official OMEGA®Service Centre
is authorised to make any modification, extension or addition to this
Warranty. OMEGASA provides no warranty against defects beyond
the rights and remedies given under this Warranty and which are
available under the Australian Consumer Law and the New Zealand
Consumer Guarantees Act 1993.
OMEGA®and ®are registered trademarks of OMEGASA
1

15
English
The crown has 3 positions:
1.
Normal position (wearing position): when the crown is positioned
against the case, the crown ensures that the watch is water-resistant.
2. Correcting the date: pull the crown out to position 2, turn the
crown forwards or backwards. Push the crown back to position 1.
3. Time setting: pull the crown out to position 3. The seconds hand
will stop. Turn the crown forwards or backwards. Synchronise the
seconds by pushing the crown back to position 1 to coincide with
a given time signal.
2Operating instructions
Quartz watch
CALIBRES 1376, 1456, 4061 (fig. IV)
The crown has 2 positions:
1. Normal position (wearing position): when the crown is posi-
tioned against the case, the crown ensures that the watch is water-
resistant.
2. Time setting: pull the crown out to position 2, turn the crown
forwards or backwards. Push the crown back to position 1.
CALIBRES 1532, 4561, 4564 (fig. I)

16
Quartz watch
Operating instructions2
The crown has 3 positions:
1.
Normal position (wearing position): when the crown is positioned
against the case, the crown ensures that the watch is water-resistant.
2. Time zone and correcting the date :pull the crown out to posi-
tion 2.Turn the crown forwards or backwards, the hour hand moves
forwards or backwards in one-hour jumps.
The date can be moved
forwards or backwards by moving the hour hand past midnight
accordingly. Push the crown back to position 1.
3. Time setting: pull the crown out to position 3. The seconds hand
will stop. Turn the crown forwards or backwards. Synchronise the
seconds by pushing the crown back to position 1 to coincide with
a given time signal.
For calibres 1424, 1532, 4561 and 4564, the end of battery life is indi-
cated by the seconds hand making 4-second jumps.The watch will con-
tinue to function for several days, but the battery must be removed and
replaced by an authorised
OMEGA service agent as soon as possible.
CALIBRES 1424, 1538 (fig. I)

17
English
The crown has 3 positions:
1. Normal position (wearing position): when the crown is
positioned against the case, the crown ensures that the watch is
water-resistant.
Occasional winding: if the watch has not been worn for 60 hours
or more, wind it up with the crown in position 1.
Calibre 8511 (manual winding)
Winding: turn the crown forward until it stops.
2. Time zone and correcting the date: pull the crown out to
position 2. Turn the crown forwards or backwards; the hour hand
moves forwards or backwards in one-hour jumps. The date jumps
forwards or backwards each time the hour hand passes midnight.
Push the crown back to position 1.
Note: the calibres 8400, 8401, 8912 and 8913 have no date indicator.
NB: when changing the time zone backwards, it is necessary to
move the hour hand back past 7 pm to ensure the date changes.
3. Time setting: hours – minutes – seconds. Pull the crown out to
position 3. The seconds hand will stop. Turn the crown forwards or
backwards. Synchronise the seconds by pushing the crown back to
position 1 to coincide with a given time signal.
Manual & self-winding watch
Operating instructions2
ê
The crown has 3 positions:
1. Normal position (wearing position): when the crown is
positioned against the case, the crown ensures that the watch is
water-resistant.
CALIBRES 8500, 8501, 8507, 8508, 8511, 8900, 8901 (fig. I)
CALIBRES 8400, 8401, 8912, 8913 (fig. VI)
CALIBRES 8601, 8611, 8902, 8903 (fig. II)
CALIBRES 8922, 8923 (fig. XII)

18
Manual & self-winding watch
Operating instructions2
Occasional winding: if the watch has not been worn for
55 hours or more, wind it up with the crown in position 1.
2. Annual calendar: pull the crown out to position 2. Turn the
crown forwards to change the date or backwards to change the
month. Push the crown back to position 1.
Note: the day following 28 or 29 February (depending on
whether it is a leap year), the date needs to be adjusted by one
or two days (crown in position 2). Ideally, the date should be
adjusted after setting the time. When correcting the date between
midnight and 10 am, the effort required for the first jump is
slightly greater than for the others.
NB: do not exit correction mode until the displays (date and
month) are centred in the aperture.
Calibres 8922, 8923
Do not switch out of correction mode unless the date is centred
in the window and the month hand centred in the month display.
3. Time setting: hours – minutes – seconds. Pull the crown out to
position 3, the seconds hand will stop. Turn the crown forwards or
backwards. Synchronise the seconds by pushing the crown back to
position 1 to coincide with a given time signal.
NB: when changing the date backwards in time setting mode, it
is necessary to wind the hands back to noon to ensure the date
changes.
The crown has 3 positions:
1. Normal position (wearing position): when the crown is
positioned against the case, the crown ensures that the watch is
water-resistant.
CALIBRES 8602, 8612 (fig. III)
ê
ê

19
English
Manual & self-winding watch
Operating instructions2
Occasional winding: if the watch has not been worn for 55 hours
or more, wind it up with the crown in position 1.
2. Correcting the date: pull the crown out to position 2. Turn the
crown forwards to change the date or backwards to change the day.
Push the crown back to position 1.
NB: do not quit setting mode if the displays (day and date) are not
properly centred in their windows.
3. Time setting: hours – minutes – seconds. Pull the crown out to
position 3. The seconds hand will stop. Turn the crown forwards or
backwards. Synchronise the seconds by pushing the crown back to
position 1 to coincide with a given time signal.
NB: when setting the day and date backwards in setting mode, it
is necessary to go back to 2 pm to ensure that the day and date
change at the right time.
The crown has 3 positions, but only positions 1 and 3 are functional
for the jewellery version of the calibre 1120 (fig.I).
1. Normal position (wearing position): when the crown is
positioned against the case, the crown ensures that the watch is
water-resistant.
Occasional winding: if the watch has not been worn for
48 hours or more (calibres 8800 and 8801: 55 hours, calibres 8520,
8521, 8700, 8701, 8704, 8705: 50 hours, calibre 1120: 44 hours,
calibre 2520: 40 hours), wind it up with the crown in position 1.
CALIBRE 2300 (fig. X)
CALIBRE 2627 (fig. V)
CALIBRES 8704, 8705 (fig. XI)
8521, 8700, 8701, 8800, 8801
CALIBRES 1120, 2500, 2507, 2520, 2610, 8520, (fig. I)
ê
ê

20
2. Correcting the date: pull the crown out to position 2, turn the
crown backwards (forwards for calibres 2520, 8520, 8521, 8700,
8701, 8704 and 8705) and push it back to position 1.
For calibre 2610 only: date adjustment is made by instantaneous
jumps.
NB: date-setting is not recommended between 8 pm and 2 am.
3. Time setting: hours – minutes – seconds. Pull the crown out to
position 3. The seconds hand will stop. Turn the crown forwards or
backwards. Synchronise the seconds by pushing the crown back
to position 1 to coincide with a given time signal.
Power reserve for calibre 2627:
• Counter at 9 o’clock: small seconds.
• Counter at 6 o’clock: power reserve
indicator.
When the watch is fully wound, the
power reserve indicator hand points
to 4/4. This means that the power
reserve is at least 44 hours.
Power reserve:
If the watch is not being worn, or during periods of low activity, the
power reserve indicator hand progressively moves anti-clockwise.
If the power reserve indicator hand is pointing to below 1/4,this means
that the watch’s power reserve is less than 10 hours. In this case, the
watch should be worn or wound by hand to prevent it from stopping.
During manual winding (crown in position 1) or when worn (self-
winding), the power reserve indicator hand moves clockwise.
Manual & self-winding watch
2Operating instructions
2627
Omega
ê

21
English
CALIBRES 2403, 8421, 8806, 8807 (fig. VIII)
The crown has 2 positions:
1. Normal position (wearing position): when the crown is
positioned against the case, the crown ensures that the watch is
water-resistant.
Occasional winding: if the watch has not been worn for 40 hours
or more (50 for the calibre 8421 and 55 for the calibre 8806 and
8807), wind it up with the crown in position 1.
Calibres 2201 and 2211 (manual winding)
Winding: turn the crown forwards until it stops.
2. Time setting: hours – minutes. Pull the crown out to position 2.
Turn the crown forwards or backwards. Push the crown back to
position 1.
For calibres 2200, 2202, 2403, 8421, 8806 and 8807: syn-
chronise the seconds by pushing the crown back to position 1
to coincide with a given time signal.
CALIBRES 2200, 2201, 2202, 2211 (fig. IX)
Manual & self-winding watch
Operating instructions2