Omron CJ - REFERENCE 10-2009 User manual

Cat. No. W474-E1-06
Programmable Controllers
SYSMAC CS Series
SYSMAC CJ Series
SYSMAC One NSJ Series
INSTRUCTIONS
REFERENCE MANUAL

OMRON, 2008
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, o
r
by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission o
f
OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is con-
stantly striving to improve its high-quality products, the information contained in this manual is subject to change without
notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility
for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.

iv CS/CJ/NSJ Series Instructions Reference Manual (W474)

v
CS/CJ/NSJ Series Instructions Reference Manual (W474)
SYSMAC CS Series
CS1@-CPU@@@-@@
SYSMAC CJ Series
CJ2H-CPU6@-EIP
CJ2H-CPU6@
CJ1@-CPU@@@-@
SYSMAC One NSJ Series
NSJ@@-@@@@@-@@@
Programmable Controllers
Instructions Reference Manual
Revised October 2009

vi CS/CJ/NSJ Series Instructions Reference Manual (W474)

vii
CS/CJ/NSJ Series Instructions Reference Manual (W474)
About this Manual:
This manual describes the ladder diagram programming instructions of the CPU Units for CS/CJ-
series Programmable Controllers (PLCs) and the NSJ-series Controllers. The CS Series, CJ Series
and NSJ Series are subdivided as shown in the following table.
Please read this manual and all related manuals listed in the table and be sure you understand infor-
mation provided before attempting to program or use CS/CJ-series CPU Units in a PLC System or an
NSJ-series Controller.
Precautions provides general precautions for using the CS/CJ-series Programmable Controllers
(PLCs), NSJ-series Controllers, and related devices.
Section 1 describes the basic information that is required to use programming instructions.
Section 2 provides a summary of instructions used with NSJ/CS/CJ-series PLCs.
Section 3 describes each of the instructions that can be used in programming NSJ/CS/CJ-series
PLCs. Instructions are described in order of function, as classified in Section 2 Summary of Instruc-
tions.
Section 4 provides instruction execution times and the number of steps for each CS/CJ-series instruc-
tion.
The Appendices provide a list of instructions in order of the mnemonics and an ASCII table.
Series Name Model numbers
CJ Series CJ2 CPU Units CJ2H-CPU6@-EIP
CJ2H-CPU6@
CJ1-H CPU Units CJ1H-CPU@@H-R
CJ1@-CPU@@H
CJ1@-CPU@@P
CJ1M CPU Units CJ1M-CPU@@
CJ1 CPU Units CJ1@-CPU@@
CS Series CS1-H CPU Units CS1G/H-CPU@@H
CS1 CPU Units CS1G/H-CPU@-EV1
CS1D CPU Units CS1D-CPU@@H
CS1D-CPU@@S
CS1D-CPU@@P
NSJ Series NSJ-series Controllers NSJ5-TQ@@(B)-G5D
NSJ5-SQ@@(B)-G5D
NSJ8-TV@@(B)-G5D
NSJ10-TV@@(B)-G5D
NSJ12-TS@@(B)-G5D
NSJ5-TQ@@(B)-M3D
NSJ5-SQ@@(B)-M3D
NSJ8-TV@@(B)-M3D

viii CS/CJ/NSJ Series Instructions Reference Manual (W474)
OMRON Product References
All OMRON products are capitalized in this manual. The word “Unit” is also
capitalized when it refers to an OMRON product, regardless of whether or not
it appears in the proper name of the product.
The abbreviation “Ch,” which appears in some displays and on some OMRON
products, often means “word” and is abbreviated “Wd” in documentation in
this sense.
The abbreviation “PLC” means Programmable Controller. “PC” is used, how-
ever, in some Programming Device displays to mean Programmable Control-
ler.
Intended Audience
This manual is intended for the following personnel, who must also have
knowledge of electrical systems (an electrical engineer or the equivalent).
Personnel in charge of installing FA systems.
Personnel in charge of designing FA systems.
Personnel in charge of managing FA systems and facilities.

ix
CS/CJ/NSJ Series Instructions Reference Manual (W474)
Read and Understand this Manual
Please read and understand this manual before using the product. Please consult your OMRON
representative if you have any questions or comments.
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a
period of one year (or other period if specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-
INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE
PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT
LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which
liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS
REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS
WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO
CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

xCS/CJ/NSJ Series Instructions Reference Manual (W474)
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the
combination of products in the customer's application or use of the products.
At the customer's request, OMRON will provide applicable third party certification documents identifying
ratings and limitations of use that apply to the products. This information by itself is not sufficient for a
complete determination of the suitability of the products in combination with the end product, machine,
system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not
intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses
listed may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or
uses not described in this manual.
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical
equipment, amusement machines, vehicles, safety equipment, and installations subject to separate
industry or government regulations.
• Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR
PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED
FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any
consequence thereof.