Omron NV3W-MR20L-V1 User manual

Advanced Usage
Advanced Usage
Ctiith
Connecting with
CPIE PLC
Designing Screens
Preparation
NV-series PT
Simple Operation
Handbook
- A case of connection to a CP1E PLC -
Table of Contents
Preparation
Required Devices 2
Wiring and Connection 4
Turning on the Power 6
Displaying the NV System Menu 7
Setting the CPIE Serial Port 8
Designing Screens
Creating New Screen Data 12
Setting the NV Communications 15
Creating Switch Parts 16
Creating Lamp Parts 19
Creating Data Parts 21
Creating Keyboard Screens 23
Creating Character Stings26
Connecting with CP1E PLC
Transferring Screen Data  28
Checking Operation 31
Advanced Usage
Switching Screens from CP1E 32
Changing Backlight Colors
from CP1E 34
Connecting PC and PLC via NV 35
The NV3W-V1 is added.

2
These are the devices required to connect an NV-series PT to a CP1E PLC.
Required Devices
Application Models
CP1E-NxxS1-type (built-in 3 ports), CP1E-NxxS-type (built-in 2 ports)
-RS-232C type (24 VDC) -
NV3Q-MR21 NV3Q-SW21
-RS-422A type (24 VDC) -
NV3Q-MR41 NV3Q-SW41
Power supply for Programmable Terminals
Use a 24-VDC power supply unit for an NV3W-V1 (24-VDC type), NV4W or NV3Q.
A power supply unit is not necessary for an NV3W-V1 RS-232C type (5-VDC type), since the 5-
V power is supplied from the PLC via the cable (XW2Z-200T-4).
PT: NV Series
PLC: CP1E Series
Compact Horizontal Models: NV3W-V1 (3.8 inch)
- RS-232C type (5 VDC) -
NV3W-MR20L-V1 NV3W-MG20L-V1
- RS-232C type (24 VDC) -
NV3W-MR20-V1 NV3W-MG20-V1
- RS-422A type (24 VDC) -
NV3W-MR40-V1 NV3W-MG40-V1
QVGA Models: NV3Q (3.6 inch)
Package PLCs with Exceptional Cost: CP1E
Three color LED backlight
of white, pink and red
NV3W-MRxx(x)-V1
Three color LED backlight
of green, orange and red
NV3W-MGxx(x)-V1
Three color LED backlight
of white, pink and red
NV3Q-MRxx
STN color
(Display colors: 4096 colors)
NV3Q-SWxx
-RS-232C type (5 VDC) -
XW2Z-200T-4 (2 m with 5-V Line)
-RS-232C type (24 VDC) -
XW2Z-200T-3 (2 m without 5-V Line)
XW2Z-500T-3 (5 m without 5-V Line)
-RS-422A type (24 VDC) -
Prepare one by referring to the Manual.
PT-to-PLC Connecting Cable
Compact Horizontal Models: NV4W (4.6 inch)
- RS-232C type (24 VDC) -
NV4W-MR21 NV4W-MG21
- RS-422A type (24 VDC) -
NV4W-MR41 NV4W-MG41
Three color LED backlight
of white, pink and red
NV4W-MRxx
Three color LED backlight
of green, orange and red
NV4W-MGxx
Note: E-type CP1E CPU Units (Basic Models) can not be used with an NV-series
PT, since they do not have a RS-232C port.
< Renewal type >

NV-series PT Simple Operation Handbook
Advanced Usage
Advanced Usage
Ctiith
Connecting with
CPIE PLC
Designing Screens
Preparation
3
FA Integrated Tool Package
CX-One Ver.4.x (4.03 or higher)
The CX-One is a package that integrates the
Support Software for OMRON PLCs and
components.
CX-One Lite Ver.4.x (4.03 or higher)
The CX-One Lite is a subset of the complete CX-
One package that provides only the Support
Software required for micro PLC applications.
Select from two packages: Included in both packages of CX-One Lite Ver.4 and CX-
One Ver.4.
* It cannot be purchased individually.
NV-Designer Ver.1.1 or higher
Screen designing software for NV
Programming software for PLC
Included in a package of CX-One Lite Ver.4.
Micro PLC Edition CX-Programmer Ver.9.
Included in a package of CX-One Ver.4.
CX-Programmer Ver.9
Select from two types of software:
NV-PC connection cable
Use a commercially available USB cable (Mini-B) to connect the NV3W-V1 or NV4W to a PC.
Use a commercially available USB cable (Type B) to connect the NV3Q to a PC.
Preparation
PC
Use a commercially available USB cable.
CP1E PLC-PC connection cable
CP1E
Type B Type A
NV4W
Connecting an NV4W
Mini-B Type A
Use a commercially available USB cable (Mini-B).
* Supporting Windows 7
(32-bit version)!
NV3Q
Connecting an NV3Q
Use a commercially available USB cable (Type B).
Type B Type A
NV3W-V1
Connecting an NV3W-V1
Mini-B Type A
Use a commercially available USB cable (Mini-B).
Note: The NV-Designer
Ver.2.0 or higher is
required to use the
NV3W-V1.

4
Wiring and Connection
Connect the devices.
* This section explains the procedure to connect an NV3W-V1 (5-VDC type) PT to a CP1E PLC.
Connecting example
Commercially available USB cable
(Type A connector – Type B connector) XW2Z-200T-4
(2 m with 5-V Line)
Connecting the NV and CP1E
Connecting an NV3W-V1 (5-VDC type) PT to the USB port on a PC
5 V power (green)
Name (color)
RD (orange)
SD (blue)
SG (pink)
NV3W-V1 (5-VDC)
* The NV3W-V1 (5-VDC type) does not need a power supply unit. The 5-V power is supplied from the PLC through the XW2Z-200T-4
Special Cable.
NV3W-MR20L-V1
PC
CP1E-N30SDx-x
Wiring for the CP1E AC power supply
Wire for the CP1E AC power supply.
Connect the NV and the CP1E with the XW2Z-200T-4 Special Cable.
FG (black)
Ground to 100 ohm or less
XW2Z-200T-4
Special Cable
(2 m with 5-V Line)
Upper terminal block
100 to 240 VAC, 50/60 Hz
Commercially available USB cable (Mini-B)

NV-series PT Simple Operation Handbook
Advanced Usage
Advanced Usage
Ctiith
Connecting with
CPIE PLC
Designing Screens
Preparation
5
The NV3W-V1 and NV4W PTs can be mounted vertically.
Mount the PT with the serial communications/power supply
connector on top.
Using a Vertically Mounted PT (NV3W-V1 and NV4W only)
When the CP1E uses a 24-VDC power supply
Wire the 24-VDC power supply as shown below.
XW2Z-200T-3
(2 m, without 5-V Line)
XW2Z-500T-3
(5 m, without 5-V Line)
When the NV3W-V1 (24-VDC type), the NV4W, or the NV3Q is connected
with a RS-232C cable
Wire the NV and the PLC as follows. The power is supplied from the external supply unit to
the PT. Name (color)
RD (orange)
SD (blue)
SG (pink)
NV3W-V1 (24-VDC)/NV4W/NV3Q
FG (black)
Ground to 100 ohm or less
24-VDC power supply
Upper terminal block
24-VDC power supply
Preparation

6
Turning on the Power
Turn on the power to the CP1E. The power is also supplied to the NV
through the RE-232C serial port on the CP1E.
If you turn ON the power to the NV after you change the DIP switch pins on the NV back face to
any setting other than default setting, the NV starts up in a special operation mode. You can use
the functions to prohibit accessing the System Menu and to clear the F-ROM.
* Do not use the NV in any settings other than shown below.
Normal operation
(default ) Prohibiting moving to System Menu F-ROM clear
Note 1: The data saved in the F-ROM includes screen data and NV configuration data.
Note 2: Other than the DIP switch setting, you can clear the F-ROM from the System Menu.
Turning on the power to the CP1E
NV startup mode
Turn on the power to the CP1E. The POWER LED indicator on the front of the CP1E lights in
green. The NV screen shows a message as follows:
Note: The message “No Screen data” is shown when the NV has no screen data.
As the NV contains no data at factory shipping, This message is shown accordingly.
Turn OFF all pins. Turn ON pin 2. Turn ON pins 2, 3, and 4.
POWER
LED
XW2Z-200T-4

NV-series PT Simple Operation Handbook
Advanced Usage
Advanced Usage
Ctiith
Connecting with
CPIE PLC
Designing Screens
Preparation
7
Displaying the NV System Menu
The System Menu is the special screen that is used to configure the NV.
Some settings such as touch switch adjustment can only be done on the
System Menu.
Accessing the System Menu
Follow the steps below to access the System Menu.
1. Touch the touch panel on the PT as shown below.
(This is common for the entire NV Series.)
1) Touch the upper left corner (A) for at least 2
seconds.
2) Then immediately touch the upper right
corner (B) and lower right corner (C) in order.
Note: Touch the points A, B, and C, one at a time in order. Do not press these points at the
same time.
2. The startup screen of the System Menu will be displayed.
The startup screen of the System Menu will be
displayed.
The next screen will be displayed if you touch
the Setting Menu or Test Menu Key.
To return to normal operating status, touch the
ESC Key.
Note: The system version is the version of the system ROM in the PT.
The default language for the System Menu is English, if there is no screen data in the PT.
The System Menu depends on the PT model. The default System Menu for the NV3W-V1
is used here.
Changing the System Menu language
The language is switchable between English and Japanese on the NV System Menu.
Select Setting Menu -Language.
Touch A for at least 2 seconds, then press B and C in order.
Preparation

8
Setting the CP1E Serial Port
To have the NV and the CP1E communications, the both serial ports must
have the same setting. Use the PLC programming tool CX-Programmer to
set the communications on the CP1E.
Be sure to change the stop bit on the PLC from the default 2 to 1
The stop bit for the NV serial communications is fixed to 1 . Therefore, the stop bit of the
PLC serial port must be changed from the default 2 to 1.
NV-CP1E communications setting example
Both the NV and the CP1E support the high speed communication of 115,200 bps.
Connect them in this baud rate.
Set the RS-232C serial ports on both of the NV and the CP1E as follows:
Mode: Host Link
Baud rate: 115,200 bps
Data length: 7
Stop bit: 1
Parity bit: Even
Communications setting for the RS-232C serial port built in the CP1E
Use the PLC programming tool CX-Programmer. Follow the steps below to set the RS-232C
serial port built in the CP1E.
* After this setting is completed, turn OFF and then ON the power of the CP1E.
Connect the CX-Programmer and the
CP1E online using a USB cable.
Change the CP1E operation mode to
“Program Mode” (Stopped).
Upload the PLC settings (including the
built-in RS-232C serial port setting)
from the CP1E.
Set the built-in RS-232C serial port on
the PLC Settings.
Write the PLC settings (including the
built-in RS-232C serial port setting) into
the CP1E.
Turn OFF and then ON the power of
the CP1E. (The settings are reflected
only after the power is turned ON.)
1
2
3
4
5
6
Note: Communications may be enabled, even when the stop bit on the PLC is 2 while the bit on the NV is 1. However,
be sure to set the both to 1.

NV-series PT Simple Operation Handbook
Advanced Usage
Advanced Usage
Ctiith
Connecting with
CPIE PLC
Designing Screens
Preparation
9
Online connection of the CX-Programmer and CP1E
1. Select Program – OMRON – CX-One – CX-Programmer – CX-Programmer from the
Windows Start Menu to start the CX-Programmer.
2. Select PLC – Auto Online – Direct Online from the menu bar.
3. In the Direct Online Dialog Box, select USB connection for the PC – PLC (CP1E)
connection type. Click the Connect Button.
Connection Type:
Select either
Serial connection or
USB connection.
1) Click the No Button.
* Click the Yes Button to upload
the program to the PC.
4. When the PC is connected with the CP1E, a new project will start.
Preparation

10
Changing the CP1E operation mode into Program
1. Select PLC – Operation Mode – Program from the menu bar.
1) Confirm that stopping the ladder
program do not cause any
problem. Click the Yes Button.
2. The CP1E operation mode changes to the Program Mode.
“Stopped” is displayed.
“Program Mode” is displayed.ｚｚｚｚｚ
Transferring, setting and writing the PLC settings
1. Double-click Settings in the project tree.
Double-click!!