Omron D2JW-011 User manual

1
Sealed Ultra Subminiature Basic Switch D2JW
Ultra-small and Highly Sealed
Degree of protection for the lead wire models
conforms to IEC IP67. (Lead wire type only)
Wide range of operating temperature from –40 °C to
85°C.
Gold crossbar contact and coil spring of fer long life
expectancy and high contact reliability.
Ordering Information
Model Number Legend
D2JW-01j-j
12 3
1. Ratings
01: 0.1
A, 30 VDC
2. Actuator
1:
Pin plunger
K1A1: Short hinge lever
K11: Hinge lever
K31: Simulated hinge lever
K21: Hinge roller lever
3. Terminal
None:
Solder terminal
MD: Molded lead wire terminal
List of Models
Actuator Model
Solder Molded lead wire
Pin plunger D2JW-011 D2JW-011-MD
Short hinge lever D2JW-01K1A1 D2JW-01K1A1-MD
Hinge lever D2JW-01K11 D2JW-01K11-MD
Simulated hinge lever D2JW-01K31 D2JW-01K31-MD
Hinge roller lever D2JW-01K21 D2JW-01K21-MD
Note: The standard lengths of the lead wires (A VS0.3f) of models incorporating them are 30 cm.

D2JW D2JW
Specifications
Ratings
Electrical ratings 0.1 A at 30 VDC (resistive load)
The ratings values apply under the following test conditions:
Ambient temperature: 20 ±2_C
Ambient humidity: 65 ±5%
Operating frequency: 30 operations/min
Minimum applicable load
1 mA at 5 VDC
Characteristics
Operating speed 1 mm to 250 mm/s (see note 1)
Operating frequency Mechanical: 240 operations/min
Electrical: 30 operations/min
Insulation resistance 100 M Ω min. (at 500 VDC)
Contact resistance
(initial value)
100 m Ω max. (molded lead wire models: 140 m Ω max.)
Dielectric strength 600 V AC, 50/60 Hz for 1 min between terminals of the same polarity
1,000 V AC, 50/60 Hz for 1 min between current-carrying metal parts and ground (see note 2), and
between each terminal and non-current-carrying metal parts
V ibration resistance Malfunction: 10 to 55 Hz, 1.5-mm double amplitude (see note 3)
Shock resistance Destruction: 1,000 m/s
2
{approx. 100G} max.
Malfunction: 200 m/s
2
{approx. 20G} max. (see note 3)
Life expectancy Mechanical: 1,000,000 operations min.
Electrical: 100,000 operations min.
Degree of protection IP67 for molded lead wire terminal models
IP50 for solder terminal models
Degree of protection against
electric shock
Class I
Proof tracking index (PTI) 175
Ambient temperature Operating: –40 ° C to 85 ° C (with no icing or condensation)
Ambient humidity Operating: 35% to 98%
Weight Approx. 7 g (molded lead wire models, pin plunger models)
Note: 1. The operating speed value shown is for pin plunger models. (For dif ferent models, contact your OMRON representative.)
2. The dielectric strength values shown apply for use with Separator (terminal type).
3. The values shown apply for malfunctions of 1 ms max.
Contact Specifications
Contact Specification Crossbar
Co ac
Material Gold alloy
Gap (standard
value)
0.5 mm
Inrush current
NC 0.1 A max.
us cu e
NO 0.1 A max.
Contact Form (SPDT)
NC
(Red*)
NO
(Blue*)
COM
(Black*)
*Indicates the color of the lead wire.
5

D2JW D2JW
Nomenclature
Rubber seal
(silicone rubber)
Cover (polycarbonate resin)
Epoxy resin
Soldered
COM
Black
NO
Blue
NC
Red
Dimensions
Note: 1. All units are in millimeters unless otherwise indicated.
2. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
3. Actuators of the molded lead wire terminals are omitted here. The dimensions (other than the terminals) and operating characteris -
tics
of the molded lead wire terminals are the same as those for the solder terminals.
Dimensions and Operating Characteristics
OF max. 2.45 N {250 gf}
RF min. 0.98 N {100 gf}
PT max. 0.6 mm
OT min. 0.3 mm
MD max. 0.1 mm
OP 8.1± 0.3 mm
OF max. 1.15 N {1 17 gf}
RF min. 0.23 N {23 gf}
PT max. 5.4 mm
OT min. 0.7 mm
MD max. 0.5 mm
OP 8.4± 0.8 mm
OF max. 0.80 N {82 gf}
RF min. 0.15 N {16 gf}
PT max. 6.4 mm
OT min. 1.4 mm
MD max. 0.7 mm
OP 8.4± 0.8 mm
PT
OP
2.35+0.05
–0.025 dia.
2.5+0.05
–0.025 dia.
1.6 dia.
Pin Plunger
D2JW-011
PT
OP
0.3 t stainless-steel
spring lever
2.5+0.05
–0.025 dia.
Short Hinge Lever
D2JW-01K1A1
2.35+0.05
–0.025 dia.
2.5+0.05
–0.025 dia.
0.3 t stainless-steel
spring lever
PT
OP
12.7
Hinge Lever
D2JW-01K11
2.35+0.05
–0.025 dia.
5

D2JW D2JW
OF max. 0.95 N {97 gf}
RF min. 0.19 N {20 gf}
PT max. 5.5 mm
OT min. 1.1 mm
MD max. 0.6 mm
OP 10.3± 0.8 mm
OF max. 0.98 N {100 gf}
RF min. 0.19 N {20 gf}
PT max. 5.2 mm
OT min. 1.1 mm
MD max. 0.5 mm
OP 14.6± 0.8 mm
1.6 dia.
PT
OP
NC (red)
NO (blue)
COM
(black)
2.35+0.05
–0.025 dia.
2.5+0.05
–0.025 dia.
Molded Lead Wire
D2JW-01jjj-MD
Note: Letters
and numbers are inserted in j by the actuator .
2.5+0.05
–0.025 dia. 2.35+0.05
–0.025 dia.
0.3 t stainless-steel
spring lever
PT
OP
Simulated Hinge Lever
D2JW-01K31
2.5+0.05
–0.025 dia. 2.35+0.05
–0.025 dia.
4.8 dia. ×2.2 resin roller
OP
PT
Hinge Roller Lever
D2JW-01K21
5

D2JW D2JW
Separator (Order Separately)
Model Separator for D2JW
Two, 2.4 ±0.1 dia.
t=0.18
Precautions
Cautions
Mounting Dimensions
Use M2.3 mounting screws with plain or spring washers to mount
the
Switch. T ighten the screws to a torque of 0.20 to 0.29 N S m {2 to
3 kgf Scm}.
Mounting Holes
M2.3 mounting holes
4.8 ± 0.1
Terminal Connection
To solder the lead to the terminal, apply a soldering iron rated at
30 W max. (temperature of soldering iron: 250 ° C max.) within 3 se -
conds.
If
soldering is not carried out under the proper conditions there is a
danger of over-heating and subsequent heat damage. Applying a
soldering
iron for too long a time or using one that is rated at more
than 30 W may degrade the Switch characteristics.
Degree of Protection
The D2JW satisfies the following test condition specified by the IEC
Publication 529:
Degree of protection: IP67
T est method:See the figure below .
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉ
Water
Leave for 30 minutes
Test piece
15 cm min
1m min
Note: Temperature dif ference between the test piece and wa -
ter
must be 5 ° C or more.
Leave the test piece in water for 30 min with the top of the test piece
submerged 15 cm or more below the water level and the bottom of
the test piece submerged 1 m or more below the water level.
This test is to check the ingress of water into the switch enclosure
after submerging the switch in water for a given time. Even if this test
condition is met, the switch cannot be used in water .
Protection Against Chemicals
Prevent the Switch from coming into contact with oil and chemicals.
Otherwise, damage to or deterioration of Switch materials may re -
sult.
Correct Use
Refer to pages 22 to 29 for common precautions.
Separator
When
mounting the Switch on a metallic surface, be sure to use a
Separator between the Switch and the mounting plate.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. T o convert grams into ounces, multiply by 0.03527.
Cat. No. B040-E1-1B
5