Omron H5CZ User manual

Step1
Step2
Step1
1) H5CZ models with a 24-VAC/12 to 24-VDC power supply use a transformer-free power supply method in
which the power supply terminals are not isolated from the signal input terminals. If a non-isolating DC
power supply is used, unwanted current paths may occasionally burn or destroy internal components
depending on the wiring. Always check the wiring sufficiently before use.
2) An inrush current of approx. 10 A will flow for a short time when the power supply is turned ON. If the
capacity of the power supply is not sufficient, the Timer may not start. Be sure to use a power supply with
sufficient capacity.
3) Maintain voltage fluctuations in the power supply within the specified operating voltage range.
4) To allow for the startup time of peripheral devices (sensors, etc.), the Timer starts timing operation between
200 to 250 ms after power is turned ON. For this reason, in operations where timing starts from power ON,
the time display will actually start from 249 ms. If the set value is 249 ms or less, the time until output turns
ON will be a fixed value between 200 and 250. The present value display will start from 250 ms. (Normal
operation is possible for set values of 250 ms or more.) In applications where a set value of 249 ms or less
is required, use start timing with signal input.
5) The input signal will not be accepted after 5 to 505 ms has elapsed from when the power supply is turned
OFF.
6) Inrush current generated by turning ON or OFF the power supply may deteriorate contacts on the power
supply circuit. Turn ON or OFF to a device with the rated current of more than 10 A.
7) Make sure that all settings are appropriate for the application. Unexpected operation resulting in property
damage or accidents may occur if the settings are not appropriate.
8) Do not leave the Timer for long periods of time at a high temperature with output current in the ON state.
Doing so may result in the premature deterioration of internal components (e.g., electrolytic capacitors).
9) EEPROM is used as memory when the power is interrupted. The write life of the EEPROM is 100,000
writes. The EEPROM is written when the power is turned OFF or when switching from function setting
,mode or Timer/Twin Timer selection mode to run mode.
10) Dispose of the product according to local ordinances as they apply.
Display Parameter name Set value Comments
timr ---*1
timm ---
outm
otim
iflt 20ms,1ms *2
otmd 1c1c,2c *2
sl-h
kypt
on-a
on-c
on1a 0to 9999 ×1,000
---
---
×1,000
on2a 0to 9999 ×1,000
on1c
on2c
---
---
---
oftr ---*1
ontr ---*1
timm up,down *2 ---
totm toff,ton,tof1,ton1
*2
iflt 20ms,1ms *2
otmd 1c1c,2c *2
sl1h ---
Mounting and Panel-cutout Dimensions Diagram
Standard panel cutout is shown in the
following diagram (conforms to DIN
43700). A space of 15 mm or greater
(a panel cut-out distance of 60 mm or
greater) is recommended towards
the Adapter's hook side to enable
easier mounting work.
1. The thickness of a mounting panel
should be 1 to 5 mm.
2. It is possible to mount Timers side by
side by mounting Adapters. (But only
towards the non-hook side.)
Application as a Timer
First, switch to a Twin Timer
•Display in RUN mode.
RUN mode.
Power ON
Timer Twin Timer
Press for 1 s.
Application as a Twin Timer
Change to "Twin Timer"
using the UKey.
Timer/Twin Timer
selection mode
Press for 1 s.
Present value
ON Set value
Present value
OFF Set value
Wire properly after checking the specifications of the power supply
voltage.
Key-protect Switch Settings
Self-diagnostic Functions
OFF (disable)
ON (enable)
* Changing mode to Timer/Twin Timer selection mode or function setting mode.
When the key-protect switch is ON,
individual key operations can be disabled
to prevent setting errors according to the
key protect levels (KP-1 to KP-7) shown
in the following table.
* Key protect levels are set in function
setting mode.
0.01 s to 99.99 s (default setting)
0.1 s to 999.9 s
1 s to 9999 s
0 min 01 s to 99 min 59 s
0.001 s to 9.999 s
0.1 h to 999.9 h
1 h to 9999 h
0 h 01 min to 99 h 59 min
0.1 min to 999.9 min
1 min to 9999 min
The characters displayed in reverse video are the default settings.
OFF time range
ON time range
UP/DOWN mode
Twin Timer
Output mode
Input signal width
Instantaneous/time-limit
Displayed only for H5CZ-L8E@.
Present value
ON duty
•Display in RUN mode. (Z mode)
Present value
Cycle time
Display Parameter name Set value Comments
Displayed only for models other than H5CZ-L8E@.
OMRON EUROPE B.V.
Wegalaan 67-69-2132 JD Hoofddorp, The Netherlands
Tel: [phone]/Fax: [phone]
OMRON ELECTRONICS LLC (U.S.A.)
Tel: [phone]/Fax: [phone]
OMRON ASIA PACIFIC PTE. LTD. (SINGAPORE)
Tel: [phone]/Fax: [phone]
OMRON (CHINA) CO., LTD.
Tel: [phone]/Fax: [phone]
OFF
Note: Refer to the datasheet (Cat. No. L111) for detailed parameter settings.
Note: Refer to the datasheet (Cat. No. L111) for detailed parameter settings.
Parameters are set with the operation keys on the front panel.
Only modes toff and ton can be
selected for H5CZ-L8E@.
•Display in RUN mode.
(except for Z mode)
Present value
Set value
Indicates a potentially hazardous situation which, if not
avoided, is likely to result in minor or moderate injury or
in property damage.
Do not allow pieces of metal, wire clippings, or fine metallic
shavings or fillings from installation to enter the product. Doing so
may occasionally result in electric shock, fire, or malfunction.
Minor injury due to explosion may occasionally occur. Do not use
the Timer where subject to flammable or explosive gas.
Fire may occasionally occur. Tighten the terminal screws to the
rated torque
P2CF socket terminals: 4.4 lb-in (0.5 N⋅m)
Minor injury due to electric shock may occasionally occur. Do not
touch any of the terminals while power is being supplied. Be sure
to mount the terminal cover after wiring.
The life expectancy of the output relay varies considerably
according to its usage. Use the output relay within its rated load
and electrical life expectancy. If the output relay is used beyond its
life expectancy, its contacts may become fused or there may be a
risk of fire. Also, be sure that the load current does not exceed the
rated load current and when using a heater, be sure to use a
thermal switch in the load circuit.
Minor electric shock, fire, or malfunction may occasionally occur.
Do not disassemble, modify, or repair the Timer or touch internal
components.
1) When mounting the Timer to a panel, tighten the two mounting screws alternately, a little at a time, so as
to keep them at an equal tightness. If the panel screws are tightened unequally, water may enter the
panel.
2) Store the Timer at the specified temperature. If the Timer has been stored at a temperature of less than
−10°C, allow the Timer to stand at room temperature for at least 3 hours before use.
3) Mounting the Timer side-by-side may reduce the life expectancies of internal components.
4) Use the Timer within the specified ranges for the ambient operating temperature and humidity.
5) Do not use in the following locations:
•Locations subject to sudden or extreme changes in temperature.
•Locations where high humidity may result in condensation.
•Locations with excessive vibration or shock.
•Locations subject to water.
•Locations subject to oil.
6) Do not use this Timer in dusty environments, in locations where corrosive gasses are present, or in locations
subject to direct sunlight.
7) Install the Timer well away from any sources of static electricity, such as pipes transporting molding
materials, powders, or liquids.
8) Internal elements may be destroyed if a voltage outside the rated voltage range is applied.
9) Wire terminal polarity correctly.
10) Separate the Timer from sources of noise, such as devices with input signals from power lines carrying
noise, and wiring for I/O signals.
11) Do not connect more than two crimp terminals to the same terminal.
12) Up to two wires of the same size and type can be inserted into a single terminals.
13) Use the specified wires for wiring. Applicable Wires: AWG 18 to AWG 22, solid or twisted, copper
14) Install a switch or circuit breaker that allows the operator to immediately turn OFF the power, and label it
to clearly indicate its function.
15) Approximately 14 V is output from the input terminals. Use a sensor that contains a diode.
16) Use a switch, relay, or other contact so that the rated power supply voltage will be reached within 0.1
seconds. If the power supply voltage is not reached quickly enough, the Timer may malfunction or
outputs may be unstable.
17) Use a switch, relay, or other contact to turn the power supply OFF instantaneously. Outputs may
malfunction and memory errors may occur if the power supply voltage is decreased gradually.
18) When changing the set value during a timing operation, the output will turn ON if the set value is changed
as follows because of the use of a constant read-in system:
Elapsed time (UP) mode: Present value ≥Set value
Remaining time (DOWN) mode: Elapsed time ≥Set value (The present value is set to 0.)
When in the remaining time mode, the amount the set value is changed is added to or subtracted from the
present value. When the set value is 0, the output turns ON the moment the signal is input. The reset
operation turns OFF the output.
19) Do not use organic solvents (such as paint thinners or benzine), strong alkali, or strong acids. They will
damage the external finish.
20) Confirm that indications are working normally, including the LCD. The indicator LCD and resin parts may
deteriorate more quickly depending on the application environment, preventing normal indications.
Periodic inspection and replacement are required.
21) The waterproof packing may deteriorate, shrink, or harden depending on the application environment.
Periodic inspection and replacement are required.
58
@45 +0.6
−0
A
A=(48n−2.5) +1
−0
Power supply voltage 100 to 240 VAC, 50/60 Hz (H5CZ-L8/-L8E)
12 to 24 VDC/24 VAC, 50/60 Hz (H5CZ-L8D/-L8ED)
Allowable voltage fluctuation range 85% to 110% of rated supply voltage (12 to 24 VDC: 90% to 110%)
Power consumption Approx. 6.2 VA at 100 to 240 VAC,
Approx. 5.1 VA/2.4 W at 24 VAC/12 to 24 VDC
Operating temperature range −10 to 55°C (−10 to 50°C if Timers are mounted side by
side) (with no icing or condensation)
Storage temperature range −25 to 70°C (with no icing or condensation)
Operating humidity range 25% to 85%
Altitude 2,000 m max.
Recommended fuse T2A, 250 VAC, time-lag, low-breaking capacity
Weight Approx. 105 g (main unit only)
Installation environment Over-voltage category III, pollution degree 2 (IEC 61812-1)
Input method
No-voltage Input ON impedance: 1 kΩmax. (Leakage current: 12 mA when 0 Ω)
ON residual voltage: 3 V max.
OFF impedance: 100 kΩmin.
Control output
Contact Output 250 V AC, 5A (resistive load)
30 V DC, 5A (resistive load)
Electrical life of relay 100,000 operations (at an ambient temperature of 23°C)
Mechanical life of relay 10,000,000 operations (at an ambient temperature of 23°C)
Degree of protection IEC IP66, UL508 Type 4X*
●Set the parameters using the UD Keys.
MODE
MODE
●Set the parameters using theNUD Keys.
---.-s
---- s
--:-- ms
---.-m
---- m
--:-- hm
---.-h
---- h
-.--- s
*1 The set values for the time range are as follows:
MODEMODE *1 The set values for the time range are the same as for Timer operation.
*2 After reaching the last set value, the UD Keys will return to the first set value.
MODEMODE
MODE +
MODE +
tim twn
func
tim
U1
U1
Key protect indicator
Level
KP-1 (default setting)
KP-2
KP-3
KP-4
KP-5
KP-6
KP-7
Mode change*
Invalid
Invalid
Invalid
Invalid
Invalid
Invalid
Invalid
Display switch in the run mode
Val i d
Val i d
Val i d
Val i d
Invalid
Invalid
Invalid
Reset Key
Valid
Invalid
Valid
Invalid
Invalid
Valid
Invalid
Up/Down Key
Valid
Valid
Invalid
Invalid
Invalid
Valid
Valid
4
3
2
1 8
7
6
5
0V
4
3
2
1 8
7
6
5
H5CZ-L8/-L8D
H5CZ-L8E/-L8ED
up,down *2
hold/0.01 to 99.99
0to 9999
1to 9999
1to 9999
H5CZ
Digital Timer
©All Rights Reserved
OMRON Corporation
INSTRUCTION MANUAL
1148242-7A
EN CAUTION
Suitability for Use
Keys to Warning Symbols
SAFETY PRECAUTIONS
CAUTION
Precautions for Safe Use Precautions for Correct Use
60 or greater
15 or greater
•Panel-cutout Dimensions Diagram
(Units: mm)
n Units mounted
side-by-side
3. If the Timers are mounted side by side,
water resistance will be lost.
• Digital Timer
• Instruction manual (this document)
Package Contents
Ratings (Specifications)
Conformance to EN/IEC Standards
•
•
*Individual mounting: Degree of protection on the front panel of the Timer conforms to UL 508
Type 4X when all of the following conditions are satisfied:
The Y92S-29 waterproof packing and Y92F-30 mounting adapter are used with the Timer.
Use only these parts for replacement.
The Timer is mounted on the flat surface of an enclosure that is rated and marked "Type
4X for Indoor Use Only."
(setting when
purchased.)
●Change from RUN Mode to Function Setting Mode.
The characters displayed in reverse video are the default settings.
MODE
MODE
Power ON
RUN mode Function
setting mode
3 s min.
3 s min.
Function setting mode
Time range
UP/DOWN mode
Output modes
Output time
Input signal width
Instantaneous/
time-limit
Only modes a-2,b,eand zcan be
selected for H5CZ-L8E@.
Display Set value
(If the output time is set to 0.00, hold
is displayed.)
Displayed for modes a,a-1,a-2,
a-3,b,b-1 and 5only. Unit: second
Displayed only for the H5CZ-L8E@.
• Models Other Than H5CZ-L8E@
• H5CZ-L8E@
Set value upper limit
Key protect level
Output ON count
alarm set value
The monitor value is only displayed.
It cannot be set. ×1,000
Instantaneous output 1 (OUT1)
ON count alarm set value
Time-limit output 2 (OUT2) ON
count alarm set value
Instantaneous output 1 (OUT1)
ON count monitor value
Time-limit output 2 (OUT2) ON
count monitor value
Output ON count
monitor value
●Change from RUN Mode to Function Setting Mode.
Power ON
RUN mode Function
setting mode
3 s min.
3 s min.
Function setting mode
Set value upper limit 1
OMRON shall not be responsible for conformity with any standards, codes, or
regulations that apply to the combination of the products in the customer's
application or use of the product.
Take all necessary steps to determine the suitability of the product for the systems,
machines, and equipment with which it will be used. Know and observe all
prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A
WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE
OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
48
a,a-1,a-2,a-3,b,
b-1,d,e,f,z,s *2
kp-1,kp-2,kp-3,kp-4,
kp-5,kp-6,kp-7 *2
Time-limit contact
output OUT2
Instantaneous
contact output
OUT1
Terminals 1 and 2 of the H5CZ-L8D are
connected internally.
(+)(−)
Contact output
Internal circuit
Signal
Reset
(+)(−)
Internal circuit
Internal circuit
Display Section
1. Key Protect Indicator
2. Control Output Indicator
3. Reset Indicator
4. Present Value Display (Main Display)
(Character height: 10 mm)
5. Time Unit Indicators (If the time range
is 0 min, 0.0 min, 0 h, 0.0 h, or 0 h 0
min, these indicators flash to indicate
timing operation.)
6. Set Value Display (Sub-display)
(Character height: 6 mm)
7. Set Value 1, 2 Indicator
Operation Key
8. Mode Key (Changes modes and setting items)
9. Reset Key (Resets present value and output)
10. Up Keys 1 to 4
11. Down Keys 1 to 4
The following displays will appear if an error occurs.
Main
display Sub-display Error Output
status Correction method Set value after
reset
e1 Not lit CPU error No change
e2 Not lit Memory error (RAM) No change
e2 sum Memory error (EEPROM)*1 OFF Factory setting
e3*2 No change Output ON count alarm
set value exceeded
No
change
Either press the Reset Key
or reset the power supply.
Reset the power supply.
The monitor value is only displayed.
It cannot be set. ×1,000
The monitor value is only displayed.
It cannot be set. ×1,000
kypt ---
on-a 0to 9999 ×1,000
on-c ---
on1a 0to 9999 ×1,000
on2a 0to 9999 ×1,000
on1c ---
on2c ---
The monitor value is only displayed.
It cannot be set. ×1,000
The monitor value is only displayed.
It cannot be set. ×1,000
• Models other than H5CZ-L8E@
• H5CZ-L8E@
Key protect level
Output ON count
alarm set value
Output ON count
monitor value
Instantaneous output 1 (OUT1)
ON count alarm set value
Time-limit output 2 (OUT2) ON
count alarm set value
Instantaneous output 1 (OUT1)
ON count monitor value
Time-limit output 2 (OUT2) ON
count monitor value
kp-1,kp-2,kp-3,kp-4,
kp-5,kp-6,kp-7 *2
The monitor value is only displayed.
It cannot be set. ×1,000
sl2h ---1to 9999
Set value upper limit 2
For details, refer to the latest datasheet (Cat. No. L111).
Thank you for purchasing the OMRON Product.
To ensure the safe application of the Product, read this
manual carefully before using the Product and always keep
it close at hand when the Product is in use.
*2 After reaching the last set value, the UD Keys
will return to the first set value.
No change
Reset Key
Reset Key
*1 This includes times when the life of the EEPROM has expired.
*2 The normal display and e3 will appear alternately.
When the Reset Key is pressed, e3 will no longer be displayed even if the alarm set value is exceeded.
(Monitoring is possible, however, because the counter will continue without clearing the output ON count.)
Displayed only for models other than H5CZ-L8E@.
When conforming to EMC standards, refer to the information provided in this Instruction Manual for cable
selection and other conditions.
This is a class A product. In residential areas it may cause radio interference, in which case the user may be
required to take adequate measures to reduce interference.
Basic insulation is provided between the power supply and input terminals. (No insulation is provided between
the power supply and input terminals for the H5CZ-L8@D.)
Basic insulation is provided between power supply and output terminals, and between input and output
terminals. When double insulation or reinforced insulation is required, apply double insulation or reinforced
insulation as defined in IEC 60664 that is suitable for the maximum operating voltage with clearances or solid
insulation.
•Installation in a Panel
H5CZ is normally installed on a flat surface in an operation panel. Use a Type 1 Enclosure for the operation
panel.
•Use an isolated source for power input for the H5CZ-L8@D.
Use the isolated source for Inputs.
•Environment
Surrounding Air Temperature: −10 to 40°C
•Power supply: The inputs are non-isolated. (Applicable to H5CZ-L8@D only)
The same power supply as the main power source should be used for that for input.
•Accessories (Order Separately)
Track Mounting/Front Connecting Socket
Flush Mounting Adapter
Waterproof Packing
8-pin
8-pin, finger-safe type
---
---
P2CF-08
P2CF-08-E
Y92F-30
Y92S-29
Precautions for Compliance with UL Standards and CSA Standards
Notice to Users of the H5CZ in the USA and Canada
Please use the following installation information instead of the general information in the instruction manuals in
order to use the product under certified conditions of UL and CSA when the product is installed in the USA or
Canada. These conditions are required by NFPA 70, National Electrical Code in the USA and the Canadian
Electrical Code, Part I in Canada and may vary from information given in the product manuals or safety
precautions.
*These dimensions vary with the type of DIN track (reference value).
P2CF-08(-E) Front-connecting
sockets (order separately)
(51)
Panel
Y92S-29 (order separately)
Waterproof Packing
Y92F-30 (order
separately)
Flush Mounting
Adapter
P3G-08 (order separately)
Back-connecting Socket
Mounting Dimensions (Units: mm)
Flush Mounting
Front panel dimensions are the
same.
Surface Mounting
H5CZ-L8@
84.87.5
H5CZ
-L8@
92.3* 90
Nomenclature
Terminal Arrangement
OFF
Parameters are set with the operation keys on the front panel.
Input Connections
No-voltage Inputs (NPN Inputs)
Open Collector Voltage Output Contact Input
Note: Operate with transistor ON Note: Operate with transistor ON Note: Operate with relay ON
0 V
Reset Signal
PLC or
sensor Sensor
0 V
Reset Signal
0 V
Reset Signal
--.-- s
48
48
3
2
8
9
5
4
6
7
10
11
1

6WHS
6WHS
6WHS


⯜⒬Go\jTs_

䑜≄ ⯜⒬G`YmTZWOⷸ⓸GẠ⬘P
ㇱ㢹G㉘㾌㟝G㛨⑅䉤
⯜⒬G`YzTY`Oⷸ⓸GẠ⬘P
ⵝ㍌G䑜䇭
㧔㧕
⯜⒬GwZnTW_Oⷸ⓸GẠ⬘P
㢨⮨G㥅㋁G㋀䁇G
⯜⒬Go\j
Ts_
⯜⒬GwYjmTW_OTlPOⷸ⓸GẠ⬘P
䖐⮨G㥅㋁G㋀䁇
QGkpuG⤼㢰㢌G㦹⪌㜄G♤⢰G␘⪹⏼␘UGO㵬ḔᵆP
 
㧖
䞈⮨ 䑀⢰⴬䉤G⮹㾡 ㉘㥉ᵆ 䏭ὤ㇠䚡
UJNS இ୔X㐐ᴸGⷈ㠸
UJNN |wVkv~uG⯜☐ இ
PVUN 㻐⥙G⯜☐G
EGFGGG[GTG୔Y
o\jTs_l㡴GBGCG
FG[⬀G㉔䈑Gᴴ⏙
PUJN 㻐⥙㐐ᴸ 㻐⥙㐐ᴸGWUWW㢰G⚀G䖐㐐⏈GIPME
⦐G╝⏼␘UG␜㠸ஔG㸼
㻐⥙G⯜☐ᴴGBޔBޔBޔBޔ
CޔCޔT㢰G⚀⬀G䖐㐐
JGMU 㢹⥙㐔䝬㐐ᴸ NTGNTG୔YG o\jTs_lG㢨㞬㢰G⚀⬀G䖐㐐G
PUNE ㍐㐐V䚐㐐G㤸䞌 DDGDG୔Y o\jTs_l㢰G⚀⬀G䖐㐐
TMI
LZQU 䇘G䘸⦐䊁䏬G⤼ⷜ
LQGLQGLQG୔Y
Go\jTs_lG㢨㞬㢌G󰶒㟤
POB 㻐⥙GvuG䟓㍌G󰶒⸨G
㉘㥉ᵆ
POD 㻐⥙GvuG䟓㍌G⯜⏼䉤 ⯜⏼䉤ᵆG䖐㐐⬀G䚔G㄄G㉘㥉㡴G
⺼ᴴ⏙䚝⏼␘UGÝXWWW
Go\jTs_l㢬G󰶒㟤
POB ㍐㐐㻐⥙Ov|{XP
vuG䟓㍌G󰶒⸨G㉘㥉ᵆ
㨪 ÝXWWWG
இG
இG
ÝXWWW
POB 䚐㐐㻐⥙Ov|{YPG
vuG䟓㍌G󰶒⸨G㉘㥉ᵆ
㨪 ÝXWWWG
POD ㍐㐐㻐⥙Ov|{XPG
vuG䟓㍌G⯜⏼䉤ᵆ
⯜⏼䉤ᵆG䖐㐐⬀G䚔G㄄G㉘㥉㡴G
⺼ᴴ⏙䚝⏼␘UGÝXWWW
POD 䚐㐐㻐⥙Ov|{YPG
vuG䟓㍌G⯜⏼䉤ᵆ
⯜⏼䉤ᵆG䖐㐐⬀G䚔G㄄G㉘㥉㡴G
⺼ᴴ⏙䚝⏼␘UGÝXWWW
இ
இ
இ
䞈⮨ 䑀⢰⴬䉤G⮹㾡 ㉘㥉ᵆ 䏭ὤ㇠䚡
PGUS இ୔XvmmG㐐ᴸGⷈ㠸
POUS இ୔XvuG㐐ᴸGⷈ㠸
UJNN |wVkv~uG⯜☐ VQGEPXOG୔Y இG
UPUN 䏬㠼䇴㢨⭬
㻐⥙⯜☐
UPGGGUPOGUPGGUPO
୔Y
⯜⒬o\jTs_lG󰶒㟤SGUPGGGḰGUPO
⬀G㉔䈑Gᴴ⏙U
JGMU 㢹⥙㐔䝬㐐ᴸ NTGNTG୔YG o\jTs_lG㢨㞬㢰G⚀⬀G䖐㐐G
PUNE ㍐㐐V䚐㐐G㤸䞌 DDGDG୔Y o\jTs_l㢰G⚀⬀G䖐㐐
இG
இG
LZQU 䇘G䘸⦐䊁䏬G⤼ⷜ
LQGLQGLQG୔Y
இG
Go\jTs_lG㢨㞬㢌G󰶒㟤
POB 㻐⥙GvuG䟓㍌G󰶒⸨G
㉘㥉㾌
㨪 ÝXWWW
POD ⯜⏼䉤ᵆG䖐㐐⬀G䚔G㄄G㉘㥉㡴G
⺼ᴴ⏙䚝⏼␘UGÝXWWW
இ㻐⥙GvuG䟓㍌G
⯜⏼䉤
Go\jTs_l㢬G󰶒㟤
POB ㍐㐐㻐⥙Ov|{XPG
vuG䟓㍌G󰶒⸨G㉘㥉ᵆ
㨪 ÝXWWW
POB 䚐㐐㻐⥙Ov|{YPG
vuG䟓㍌G󰶒⸨G㉘㥉ᵆ
㨪 ÝXWWW
POD ㍐㐐㻐⥙Ov|{XPG
vuG䟓㍌G⯜⏼䉤ᵆ
⯜⏼䉤ᵆG䖐㐐⬀G䚔G㄄G㉘㥉㡴G
⺼ᴴ⏙䚝⏼␘UGÝXWWW
இ
POD 䚐㐐㻐⥙Ov|{YPG
vuG䟓㍌G⯜⏼䉤ᵆ
⯜⏼䉤ᵆG䖐㐐⬀G䚔G㄄G㉘㥉㡴G
⺼ᴴ⏙䚝⏼␘UGÝXWWW
இ
G䑜≄GᴴḩG㾌㍌⓸
O␜㠸aGP
䖐㨴G䑜≄G䀘䏬⏈G㙸⣌㢌GἬ⫰ḰGᵍ㏩⏼␘UG
Okpu[Z^WWG㨴ᶤஃ
㛨⑅䉤㢌G䟹G㽕Gⵝ䛙㜄G␴䚐G㉘㾌Gᴸ󰵾㡴G
㣅㛹㉥㡸GḔ⥘䚌㜠GX\G㢨ㇵO䑜≄G䀘䏬Gᴸ󰵾G
]WGG㢨ㇵPG⛜㛨⡜⫨Gᶷ㡸GỀ䚝⏼␘U


㢨ㇵ
㢨ㇵ
غ
㧗 ࡯
㨰XUG㉘㾌G䑜≄㢌G䑄G▄󰾭⏈GX¥\ᴴG
㤵␭䚝⏼␘U
㨰YUG㛨⑅䉤G㉘㾌⪰G䋩䚨Gⴴ㵝G㉘㾌ᴴG
ᴴ⏙䚝⏼␘UGO␜SG䟹㢨G㛺⏈Gⵝ䛙⬀Gᴴ⏙P
㨰ZUGⴴ㵝G㉘㾌G㐐㜄⏈G⇨㍌㉥㢨G㛺㛨㬅⏼␘U
ᵐGⴴ㵝G㉘㾌
$
$㧔Q㧙㧕
㧗
࡯
䔠㣙G⇨㟝
G㥐䖼⸬㷨
G㼜Ἵ㉘⮹㉐O⸬㉐P
㉘㾌GⵃG䑜≄GᴴḩG㾌㍌⓸
G㉘㾌G㾌㍌⓸O␜㠸aGP
㤸⮨G⺴⺸㢌G㾌㍌⏈G㤸G⯜⒬Gḩ䋩㢹⏼␘U
cㇱ㢹G㉘㾌e
c䖐⮨G㉘㾌e
ltjG㤵䚝㉥㡸G㠸䚐G䀴㢨⽈G㉔㥉SGὤ䇴G㦤ᶨ㜄G␴䚨㉐⏈G⸬G㼜Ἵ㉘⮹㉐㢌G
ὤ㣠⇨㟝㡸G㵬㦤䚨G㨰㐡㐐㝘U
⸬Gㇵ䖼㡴଴GhଵOḩ㛹G䞌󰶒Gㇵ䖼P㢹⏼␘UG㨰䈑G䞌󰶒㜄㉐G㇠㟝䚌⮨G
㤸䑀ⵝ䚨㢌G㠄㢬㢨G╔G㍌G㢼㏩⏼␘UG㢨G󰶒㟤G㤸䑀ⵝ䚨㜄G␴䚐G㤵㤼䚐G␴㵹㢨G
䙸㟈䚝⏼␘U
㤸㠄T㢹⥙␜㣄ᴸ㡴Gὤ㸼㤼㜤㢹⏼␘U
O⯜⒬o\jTs_k⏈G㤸㠄T㢹⥙␜㣄ᴸ㡴G⽸㤼㜤㢹⏼␘UP
㤸㠄T㻐⥙SG㢹⥙T㻐⥙␜㣄ᴸ㡴Gὤ㸼㤼㜤㢹⏼␘U
㢨㩅㤼㜤G䝭㡴Gᵉ䞈㤼㜤㢨G䙸㟈䚔G󰶒㟤SGḩᴸᶤ⫠⇌GḔ㷨㤼㜤G☥㡸G䋩䚨G
㺐Ḕ㇠㟝㤸㚉㜄G㤵䚝䚐Gplj]W]][㜄G㥉㢌╌㛨G㢼⏈G㢨㩅㤼㜤G䝭㡴Gᵉ䞈㤼㜤㡸G
㐘㐐䚨G㨰㐡㐐㝘U
luVpljGἐ󰵾␴㢅㜄GḴ䚌㜠
㤸㠄㤸㚉G ืhjXWW¥Y[W}G\WV]Wo¡
G ืhjY[}G\WV]Wo¡ உ kjXY¥Y[}
䛼㟝㤸㚉Gⷴ┍Gⷈ㠸G 㥉󰵾㤸㠄㤸㚉㢌G_\¥XXW୿ஂkjXY¥Y[}⏈`W¥XXW୿ஃ
㋀⽸㤸⥙G 㚱G]UYG}hSGhjGXWW¥Y[WG}G
G 㚱G\UXG}hVYU[G~SGhjGY[G}VkjGXY¥Y[G}
㇠㟝㝜⓸ⷈ㠸G இXW¥அ\\୅GOⴴ㵝G㉘㾌G㐐aGஇXW¥அ\W୅P
G O␜SG󰶅⾍½󰶅⦐ᴴG㛺㡸GᶷP
⸨㦨㝜⓸ⷈ㠸G இY\¥அ^W୅GO␘⬀SG󰶅⾍½󰶅⦐ᴴG㛺㡸GᶷP
㇠㟝㨰㠸㏩⓸G Y\¥_\୿
Ḕ⓸G YSWWWG㢨䚌
㻈㷐G䘜㪼G {YhSGhjY\W}SG䇴㢸⤠ἬG䘜㪼SG㤴㵜␜㟝⣽
㫼⣽G 㚱GXW\GO⸬㷨⬀P
㉘㾌䞌󰶒G Ḱ㤸㚉G㾨䊀Ḕ⫠๊SG㝘㜰⓸YGOplj]X_XYTX㜄G♤⪸P
㢹⥙Gⵝ㐑
ଝⱨ㤸㚉G㢹⥙G ␜⢱G㐐G㢸䙰⒌㏘aGXȳG㢨䚌GOWȳ㢰G⚀G㡔㻐㤸⪌GG
G XYhPSG␜⢱G㐐G㣈⪌G㤸㚉aGZG}G㢨䚌SGᵐⵝG㐐GG
G 㢸䙰⒌㏘aGXWWȳG㢨ㇵ
㥐㛨㻐⥙
ଝ⫨⤼㢨G㻐⥙G hjY\W}G\hGO㤴䚡⺴䚌P
G kjZW}G\hGO㤴䚡⺴䚌P
⫨⤼㢨㢌G㤸ὤ㤵G㍌⮹GGXW⬀䟀GO㨰㠸G㝜⓸G㦤ᶨaGYZ୅P
⫨⤼㢨㢌Gὤ󰶙㤵G㍌⮹GGXWWW⬀䟀GO㨰㠸G㝜⓸G㦤ᶨaGYZ୅P
⸨䝬GẠ㦤G pljGἐ󰵾Gpw]]SG|s\W_G{G[GQ
QG␜䖼G㉘㾌aGG䘸⤤䏬⺴㢌G⸨䝬GẠ㦤⏈G㙸⣌㢌G㦤ᶨ㢨G⯜▄G㻝㦥═G󰶒㟤㜄G
|s\W_G{G[Gἐ󰵾㜄G⬒㏩⏼␘UGG
ืⵝ㍌GḔⱨG䑜䇭G⯜⒬`YzTY`㝴G㉘㾌㟝G㛨⑅䉤G⯜⒬`YmTZW㡸G
䇴㢨⭬㝴G䚜󰾭G㇠㟝䚐␘UGẄ䞌G㐐㜄⓸G㢨☘G⺴䖼㡸G㇠㟝䚐␘U
ื䇴㢨⭬⏈Gˈ{G[GGpG|Gvˉ⢰⏈G䖐㐐ᴴG㢼⏈G㥐㛨ⵉ㏘㢌G
䓽⮨㜄G㉘㾌䚐␘U
㥉󰵾GO㇠㛅P
㤸⮨䇘㜄㉐Gὤ⏙G㉘㥉㡸G䚝⏼␘U
G㟨㤸G⯜☐⪰Gὤ⏙㉘㥉G⯜☐⦐G㤸䞌䚝⏼␘U
㤸㠄䍠㢹 ὤ⏙㉘㥉G⯜☐ 㟨㤸G⯜☐
Z㸼G㢨ㇵ
Z㸼G㢨ㇵ
02'(
02'(
GᴵG䑀⢰⴬䉤⪰G6%䇘⦐G㉘㥉䚝⏼␘U
ⵌ㤸ⱬ㣄⏈Gḩ㣙㻐䚌G㐐㢌G㉘㥉㢹⏼␘U
㤸⮨䇘㜄㉐Gὤ⏙G㉘㥉㡸G䚝⏼␘U
G㟨㤸G⯜☐⪰Gὤ⏙㉘㥉G⯜☐⦐G㤸䞌䚝⏼␘U
㤸㠄䍠㢹 ὤ⏙㉘㥉G⯜☐ 㟨㤸G⯜☐
Z㸼G㢨ㇵ
Z㸼G㢨ㇵ
tvkl
tvkl
GᴵG䑀⢰⴬䉤⪰G6%䇘⦐G㉘㥉䚝⏼␘U
ⵌ㤸ⱬ㣄⏈Gḩ㣙㻐䚌G㐐㢌G㉘㥉㢹⏼␘U
䖐㐐 㐐ᴸGⷈ㠸
  WUWX¥``U``ஂ㸼ὤᵆஃG
  WUX¥```U`G
X¥````G
  WWX¥``\`G
  WUX¥```U`G
 X¥````G
  WWX¥``\`G
  WUX¥```U`G
X¥````G
  WUWWX¥`U```G
୔XaG㐐ᴸGⷈ㠸㢌G㉘㥉ᵆ⏈G␘㢀ḰGᵍ㏩⏼␘U
୔YaG㉘㥉ᵆᴴG⫼㫴⫽G↑⺴⺸㜄G㞈㡸G⚀G6%G䇘⦐G␘㐐G㚒⺴⺸㡰⦐G
─㙸ᵅ⏼␘U
G㟨㤸G⯜☐㜄㉐㢌G䖐㐐GOG⯜☐P
󰶙㐐ᵆ
vuG◴䐤G⽸㡜
󰶙㐐ᵆ
㨰ὤG㐐ᴸ
tvkltvkl
䇴㢨⭬⦐G㇠㟝╔G󰶒㟤 䏬㠼G䇴㢨⭬⦐G㇠㟝䚔G󰶒㟤
䇘G䘸⦐䊁䏬G㏘㠸㾌G㉘㥉
␜㣄ⵤ㾌
㣄ὤ㫸␜ὤ⏙
G㟨㤸G⯜☐㜄㉐㢌G䖐㐐
ὤ
⏙
㉘
㥉
G
⯜
☐
ὤ
⏙
㉘
㥉
G
⯜
☐
୔XaG㐐ᴸGⷈ㠸㢌G㉘㥉ᵆ⏈଴䇴㢨⭬⦐G㇠㟝䚔G󰶒㟤ଵ㝴Gᵍ㏩⏼␘UG
୔YaG㉘㥉ᵆᴴG⫼㫴⫽G↑⺴⺸㜄G㞈㡸G⚀G6%G䇘⦐G␘㐐G㚒⺴⺸㡰⦐G─㙸㝩⏼␘U
󰶙㐐ᵆvmmG
㉬䏬G㐐ᴸ
󰶙㐐ᵆvuG
㉬䏬G㐐ᴸ
tvkl
㟨㤸G⯜☐
㤸㠄Gvu
tvkl 㧗
X㸼G⌸⪨ὤ
tvkl 㧗
X㸼G⌸⪨ὤ
UJN
䇴㢨⭬
6䇘⦐଴䏬㠼G䇴㢨⭬ଵ⦐G
ⷴ󰶒䚨G㨰㐡㐐㝘U
UXO
䏬㠼G䇴㢨⭬
GVOD
UJN
6X
6X
ὤ㦹㉔䈑G⯜☐
⬜G㷌㢀㜄G䏬㠼G䇴㢨⭬⦐G㤸䞌䚝⏼␘U
䇘G䘸⦐䊁䏬G䖐㐐
୔G䇘G䘸⦐䊁䏬G⤼ⷜ㡴Gὤ⏙㉘㥉G
⯜☐㜄㉐G㉘㥉䚝⏼␘U
vuGO㡔䟜P
vmmGOⱨ䟜P
O㻐䚌G㐐G㉘㥉P
஄଴ὤ㦹㉔䈑⯜☐ଵื଴ὤ⏙㉘㥉⯜☐ଵ⦐㢌G㢨┍
⤼ⷜ
rwTXO㸼ὤᵆP
rwTY
rwTZ
rwT[
rwT\
rwT]
rwT^
஄⯜☐G㢨┍
⺼ᴴ
⺼ᴴ
⺼ᴴ
⺼ᴴ
⺼ᴴ
⺼ᴴ
⺼ᴴ
㟨㤸G⯜☐㜄㉐㢌G䖐㐐G㤸䞌
ᴴ⏙
ᴴ⏙
ᴴ⏙
ᴴ⏙
⺼ᴴ
⺼ᴴ
⺼ᴴ
⫠㉿䇘
ᴴ⏙
⺼ᴴ
ᴴ⏙
⺼ᴴ
⺼ᴴ
ᴴ⏙
⺼ᴴ
|wVGkv~u䇘
ᴴ⏙
ᴴ⏙
⺼ᴴ
⺼ᴴ
⺼ᴴ
ᴴ⏙
ᴴ⏙
㢨ㇵ㢨Gⵐ㈑䚼㡸G㐐㜄⏈G㙸⣌㝴Gᵍ㢨G䖐㐐╝⏼␘U
䚐ạ㝘⳴⦔㥐㛨ὤὤ㨰㐑䟀㇠
㨰㋀G㉐㟬㐐Gᵉ⇜ẠG⊰䜸┍GX[Yⶼ㫴G㜵䗁⾀♝GY㽩
O㫴䚌㷔G^䝬㉔G⊰䜸㜡GYⶼG㻐ẠP
㤸䞈V䑝㏘GOWYP\X`TZ`__GVGOWYP\X`TZ`_^
䝼䓌㢨㫴GaVVUUUUV
஄XUGllwTyvt㢌G㤴㣙G㍌⮹㢨G␘╄㡸G󰶒㟤⓸G䔠䚜U
஄YUGF⏈G⸨䋩G䖐㐐⪰Gⶼᴼ㙸G䖐㐐䚐␘UG
ଝଝG⫠㉿䇘⪰G⌸⪨⮨G󰶒⸨G㉘㥉ᵆG㢨ㇵ㢨⢰⓸GF⏈G䖐㐐╌㫴G㙾㏩⏼␘
ଝଝGO␜SG㻐⥙GvuG䟓㍌⏈G㫴㠀㫴㫴G㙾ḔG󰶙㋁G㾨㟨䏬╌ὤG⚀ⱬ㜄G⯜⏼䉤⏈Gᴴ⏙PUG
㥐X䖐㐐
F
F
F
FG஄Y
㥐Y䖐㐐
㋀☥
㋀☥
TVN
ⷴ䞈G㛺㢀
G⇨㟝
jw|G㢨ㇵ
⮈⯜⫠G㢨ㇵGOyhtP
⮈⯜⫠G㢨ㇵG
Ollw
 yvtPGQX
㻐⥙GvuG䟓㍌G㝘ⶸ
㻐⥙Gㇵ䈐
vmm
vmm
vmm
ⷴ䞈G㛺㢀
G ⸩ỴGⵝⷉ
⫠㉿䇘G䝭㡴G㤸㠄G
㣠䍠㢹
㤸㠄G㣠䍠㢹
⫠㉿䇘
⫠㉿䇘
⸩ỴG䟸㢌G㉘㥉㾌
ⷴ䞈G㛺㢀
ⷴ䞈G㛺㢀
㻐䚌G㐐㢌Gㇵ䈐
ⷴ䞈G㛺㢀
ื䇴㢨⭬㢌G㤸㠄㇠㛅㡸G䞉㢬䚐G䟸G㇠㟝䚨G㨰㐡㐐㝘U
[
Z
Y
X _
^
]
\
ஂஅஃஂஇஃ
W}
⇨⺴䟀⦐
㐐Ἤ≄
⫠㉿G
㥅㥄㻐⥙
[
Z
Y
X _
^
]
\
ஂஅஃஂஇஃ
⇨⺴䟀⦐
㍐㐐㥅㥄㻐⥙
Gv|{Y
⇨⺴䟀⦐
㍐㐐㥅㥄㻐⥙G
v|{X
⯜⒬Go\jTs_VTs_k
⯜⒬Go\jTs_lVTs_lk
⯜⒬Go\jTs_k㢌Gྙஇྚ␜㣄⏈G⇨⺴㜄G
㥅㋁╌㛨G㢼㏩⏼␘U
㤸⮨⺴㢌⮹㾡
ྙ䇘G⸨䝬G䖐㐐
ྚ㥐㛨㻐⥙䖐㐐
ྛ⫠㉿G䖐㐐
ྜ󰶙㐐ᵆO㥐X䖐㐐PGOⱬ㣄G⋆㢨GXWP
ྜྷ㐐ᴸ␜㠸䖐㐐
OWืWUWืWืWUWืWW㢌Gⷈ㠸㜄㉐⏈G󰶙㐐G
㩅㢨⢰⏈G䖐㐐⦐G㥄⮬╝⏼␘UP
ྞ㉘㥉ᵆO㥐Y䖐㐐Oⱬ㣄G⋆㢨G]PP
ྟ㉘㥉ᵆXSGY䖐㐐
٨䖐㐐⺴
Y
X
^
_
[
Z
\
]
`
XW
ྠ⯜☐䇘O⯜☐G㢨┍SG㉘㥉䚡⯝㡸G㤸䞌䚝⏼␘UP
ྡ⫠㉿䇘O󰶙㐐ᵆ㝴G㻐⥙㡸G⫠㉿䚝⏼␘UP
ྡྷ|w䇘G XGG¥GG[
ྣkv~u䇘G XGG¥GG[
٨㦤㣅䇘⺴⺸
VQGEPXOG୔Y
BGBGBGBGCGC
IPME㧛㨪
LQGLQGLQGLQ
㨪
LQGLQGLQGLQ
㨪
㨪
㨪
㉘㥉G⫠⴬䏬Gㇵ䚐
㉘㥉G⫠⴬䏬XGㇵ䚐
㉘㥉G⫠⴬䏬YGㇵ䚐
TMI
TMI
tvkl
䇘G䘸⦐䊁䏬G㏘㠸㾌ᴴG଴vuଵ
㢰G⚀㜄⏈G㙸⣌G䖐㢌G䇘G
䘸⦐䊁䏬G⤼ⷜOrwTX¥rwT^P㜄G
♤⢰GᴵG䇘㢌G㦤㣅㡸G㥐䚐䚌㜠G
㝘㉘㥉㡸Gⵝ㫴䚔G㍌G㢼㏩⏼␘U
G㟨㤸⯜☐㜄㉐㢌䖐㐐
<⯜☐㥐㞬
⫠㉿
㐐Ἤ≄
⫠㉿
㐐Ἤ≄
⫠㉿
㐐Ἤ≄
9 9 9
XX
Xஃ⯜⒬Go\jG㐐⫠㪼㢌GhjY[}VkjXYTY[}G㤸㠄G䇴㢹㡴G㤸㠄G␜㣄㝴G㐔䝬G㢹⥙G␜㣄Gᴸ㢨G
㤼㜤G╌㫴G㙾㡴G䏬⣐㏘⤼㏘Gⵝ㐑㢹⏼␘UG⽸㤼㜤䝉Gkj㤸㠄㡸G㇠㟝䚔G󰶒㟤SGⵤ㉔㜄G
♤⢰㉐⏈G㤸⪌G㡔㢹㡰⦐G㢬䚨Gᴸ䝭G⇨⺴G⺴䖼㢨G㋀㋄O䑀ṨP╔G㟤⥘ᴴG㢼㏩⏼␘UG㇠㟝G
㤸㜄Gⵤ㉔㡸G㣌G䞉㢬䚨G㨰㐡㐐㝘UG
Yஃ㤸㠄G䍠㢹G㐐㜄⏈G㬛㡴G㐐ᴸ㢨㫴⬀G─㢹㤸⪌ᴴG䢌⤠O㚱GXWhPG㤸㠄㢌G㟝⣽㜄G♤⢰㉐⏈G
ὤ┍䚌㫴G㙾㡸G㍌G㢼㡰⳴⦐G㻝⺸䚐G㟝⣽㢌G㤸㠄㡸G㇠㟝䚨G㨰㐡㐐㝘UG
Zஃ㤸㠄㤸㚉㢌Gⷴ┍ⷈ㠸⏈G䛼㟝ⷈ㠸G⇨⦐G䚨G㨰㐡㐐㝘U
[ஃ䇴㢨⭬G㨰ⷴὤὤO㉰㉐G☥PᴴGẠ┍╌⏈G㐐ᴸ㡸GḔ⥘䚌㜠SG㤸㠄㡸Gvu䚐G䟸GYWW¥Y\WG
󰶒ḰG䟸㜄G䇴㢨⭬G┍㣅㡸G㐐㣅䚝⏼␘UG㢨G⚀ⱬ㜄G㤸㠄G㏘䇴䏬⪰G䚔G󰶒㟤GY[`G㢨䚌㢌G
㉘㥉㜄㉐⏈G㻐⥙㢨Gvu╔G⚀ᾀ㫴㢌G㐐ᴸ㢨GYWW¥Y\WGⷈ㠸G⇨㜄㉐⏈G㢰㥉䚐Gᵆ㢨G
╌⳴⦐G㨰㢌䚨G㨰㐡㐐㝘UG❄G󰶙㐐㾌G䖐㐐⏈GY\W⺴䉤G㐐㣅╝⏼␘UGOY\WG㢨ㇵ㢌G
㉘㥉㜄㉐⏈G䋩ㇵG┍㣅䚝⏼␘UPGY[`G㢨䚌㢌G㉘㥉㢨G䙸㟈䚐G󰶒㟤㜄⏈G㐐Ἤ≄G㏘䇴䏬㜄㉐G
㇠㟝䚨G㨰㐡㐐㝘U
\ஃ㤸㠄Gvmm⦐⺴䉤\¥\W\G󰶒ḰG䟸㜄⏈G㢹⥙╌㫴G㙾㡰⳴⦐G㨰㢌䚨G㨰㐡㐐㝘U
]ஃ㤸㠄GvuVvmm㐐㢌G─㢹G㤸⪌⦐G㢬䚨G㤸㠄䟀⦐ㇵ㢌G㥅㥄㢨G㜨䞈╔G㍌G㢼㡰⳴⦐G㥉󰵾G
XWhG㢨ㇵ㢌Gὤὤ㜄㉐Gᵐ䔄䚔Gᶷ㡸GỀ䚝⏼␘U
^ஃᴵ㦹G㉘㥉ᵆ⏈G󰶙㽕␴ㇵ㜄G⬒㻈㛨G㝠ⵈ⪨󰵡G㉘㥉䚨G㨰㐡㐐㝘UG㉘㥉⇨㟝ḰG󰶙㽕␴ㇵ㢌G
⇨㟝㢨G␘⪰G󰶒㟤G㢌⓸㾌G㙾㡴G┍㣅㡰⦐G㢬䚨G㣙㾌G䑀㋄G䝭㡴G㇠Ḕ㢌G㠄㢬㢨G╝⏼␘U
_ஃḔ㝜㜄㉐G㣙㐐ᴸG㻐⥙㤸⪌ᴴG䢄⪨⏈Gㇵ䈐㜄㉐Gⵝ㾌╌⮨G⇨⺴⺴䖼O㤸䚨䂌⒨㉐G☥P㢌G
㜨䞈⪰G㚒␭ὬG㟤⥘ᴴG㢼㡰⳴⦐G䙰䚨G㨰㐡㐐㝘U
`ஃllwTyvt㜄G㢌䚨G㥉㤸ὤ㛩㢨G㢨⨜㛨㬅⏼␘UGllwTyvt㢌G㤴㣙G㍌⮹㡴GXW⬀䟀㢹⏼␘UG
llwTyvt㡴G㤸㠄Gvmm㐐GⵃGὤ⏙㉘㥉G⯜☐Vὤ㦹㉔䈑G⯜☐㜄㉐G㟨㤸G⯜☐⦐G㢨┍╔G⚀G
㤴㣙╝⏼␘U
XWஃ⸬G㥐䖼㡸G䔄ὤ䚔G󰶒㟤㜄⏈GᴵG㫴ⵝ㣄㾌␜㷨㢌G㇤㛹䔄ὤⱰG㷌⫠ⵝⷉ㜄G♤⢰G㷌⫠䚨G
㨰㐡㐐㝘UG
vtyvuG㨰㐑䟀㇠
o\j
♈㫴䉬G䇴㢨⭬
rvy 㼜Ἵ㉘⮹㉐
vtyvuG㥐䖼㡸GẠ㢹䚨G㨰㊈㉐Gᵄ㇠䚝⏼␘UG
⸬G㥐䖼㡸G㙼㤸䚌ḔG㝠ⵈ⦐G㇠㟝䚌ὤG㠸䚨㉐SG
㇠㟝䚌㐐ὤG㤸㜄G㼜Ἵ㉘⮹㉐G⇨㟝㡸G㻝⺸䢼G㍍㫴䚨G㨰㐡㐐㝘UG
␘G㢱㡴G䟸㜄⓸G䚡ㇵGᴴᾀ㟨Gḧ㜄G▄ḔG㇠㟝䚨G㨰㐡㐐㝘U
$OO5LJKWV5HVHUYHG
㝠ⵈ⪨󰵡G␘⨜㫴G⯯䚌⮨G㠸䜌䚌ὤG⚀ⱬ㜄G
⚀⦐⏈G󰶒ㇵG❄⏈G㩅㥉⓸㢌Gㇵ䚨⪰G㢹ᶤ⇌G
Ɒ㤵G㋄䚨⪰G㢹󰵡G╔G㟤⥘ᴴG㢼㏩⏼␘U
㙼㤸ㇵ㢌G㨰㢌㇠䚡 ㇠㟝ㇵ㢌G㨰㢌㇠䚡
G󰶒Ḕ䖐㐐㢌G㢌⴬
㨰㢌
㨰㢌
󰶒⴬䚐Gᵄ㤸SGⵐ䞈SGὤὤGḔ㣙㢨Gᴸ䝭G㢰㛨⇔G
㟤⥘ᴴG㢼㏩⏼␘UG㥐䖼G㙼㜄GἼ㋁SG⓸㉔G䝭㡴G㉘㾌G
ᴴḩG㩅㜄Gᴴ⨜ᴴG䝰㢹╌㫴G㙾󰵡G䚨G㨰㐡㐐㝘U
䔡ⵐ⦐G㢬䚨Gᴸ䝭G󰶒⴬䚐Gㇵ䚨⪰G㢹㡸G㟤⥘ᴴG
㢼㏩⏼␘UG㢬䞈㉥SG䔡ⵐ㉥Gᴴ㏘ᴴG㢼⏈Gḧ㜄㉐⏈G
㇠㟝䚌㫴G⫼㐡㐐㝘U
ᴸ䝭Gⵐ䞈╔G㟤⥘ᴴG㢼㏩⏼␘UG␜㣄G⇌㇠⏈G㙸⣌㢌G
ἐ㥉G䋔䆠⦐G㷨󰶅䚨G㨰㐡㐐㝘U
wYjmG㋀䁇G␜㣄aG[U[GsTpGOWU\Gu½P
ᵄ㤸㡰⦐G㢬䚨G󰶒⴬䚐Gㇵ䚨⪰G㢹㡸G㟤⥘ᴴGᴸ䝭G
㢼㏩⏼␘UG䋩㤸G㩅㜄⏈G␜㣄㜄G㥅㸽䚌㫴G⫼㐡㐐㝘UG
❄Gⵤ㉔G䟸㜄⏈Gⵌ☐㐐G␜㣄G䀘ⶸ⪰G㉘㾌䚨G
㨰㐡㐐㝘U
㻐⥙G⫨⤼㢨㢌G㍌⮹㡴Gᵐ䔄㟝⣽SGᵐ䔄㦤ᶨ㜄G♤⢰G
䆠󰵡G␠⢰㫴ὤG⚀ⱬ㜄Gⵌ☐㐐G㐘㇠㟝G㦤ᶨ㡸G
Ḕ⥘䚌㜠G㥉󰵾⺴䚌SG㤸ὤ㤵G㍌⮹G䟓㍌G⇨㜄㉐G
㇠㟝䚨G㨰㐡㐐㝘UG㍌⮹㡸G≌㛨㉔Gㇵ䈐㜄㉐G
㇠㟝䚌⮨G㥅㥄G㟝㵝㢨⇌G㋀㋄╔G㟤⥘ᴴG㢼㏩⏼␘U
❄䚐G⺴䚌㤸⪌⏈Gⵌ☐㐐G㥉󰵾G㢨䚌㜄㉐G㇠㟝䚌ḔSG
䢼䉤G☥㡸G㇠㟝䚔G󰶒㟤㜄⏈Gⵌ☐㐐G⺴䚌䟀⦐㜄G
㉐⯜G㏘㠸㾌⪰G㇠㟝䚨G㨰㐡㐐㝘U
ᴴⷰ㟨Gᵄ㤸SGⵐ䞈SGὤὤGḔ㣙㢨Gᴸ䝭Gⵐ㈑䚔G
㟤⥘ᴴG㢼㏩⏼␘UG⺸䚨SGᵐ㦤SG㍌⫠䚌ᶤ⇌G⇨⺴㜄G
㋄␴㫴G⫼㐡㐐㝘U
㇠㟝㐐G䞉㢬㇠䚡
␘㢀G㟝⓸⦐G㇠㟝╌⏈G󰶒㟤G␭㇠G㜵㛹␨␭㣄㝴Gㇵ␨䚐G䟸G㇠㛅㉐G☥㡸G䋩䚨G
䞉㢬䚌⏈G䚐䓬SG㥉󰵾GⵃG㉥⏙㜄G␴䚨G㤵䚝䚐G㇠㟝ⵝⷉG䝭㡴G⬀㢰㢌G󰶒㟤GḔ㣙㢨G
ⵐ㈑䚨⓸G㠸䜌㡸G㺐㋀䞈䚔G㍌G㢼⏈G㙼㤸䟀⦐G☥㢌G㙼㤸␴㵹㡸GᵉẠ䚌㐡㐐㝘UG
PG㝙㞬G㟝⓸SG㣔㣠㤵㢬G䞈䚍㤵G㝘㜰G䝭㡴G㤸ὤ㤵Gⵝ䚨⪰Gⵏ⏈G㟝⓸G❄⏈G㾨䇼⦐ἬG
ⵃG㼜Ἵ㉘⮹㉐G☥㜄Gὤ㣠╌㫴G㙾⏈G㦤ᶨ㢨⇌G䞌󰶒㜄㉐㢌G㇠㟝
PG㠄㣄⥙G㥐㛨㉘⽸SG㋀ᴵG㉘⽸SG㷔⓸ื䚡ḩื㵜⣽G㉘⽸SG㢌㟝Gὤ󰶙SG㝘⢱ὤ󰶙SG
㙼㤸㣙㾌GⵃG䚽㥉ὤḴ㢨⇌GᵐⷸG㛹󰶙㢌Gἐ㥐㜄G♤⪨⏈G㉘⽸
PG㢬⮹㢨⇌G㣠㇤㜄G㠸䜌㡸G⴬㾔G㍌G㢼⏈G㐐㏘䊐ืὤ󰶙ื㣙㾌
PG
ᴴ㏘SG㍌⓸SG㤸ὤḩἽ㐐㏘䊐㢨⇌GY[㐐ᴸG㜤㋁㟨㤸㐐㏘䊐G☥G⋆㡴G㐔⧤㉥㢨G
㟈Ạ╌⏈G㉘⽸
PGὤ䇴SGㇵὤGP¥P㜄G㨴䚌⏈GḔ⓸㢌G㙼㤸㉥㢨G㟈Ạ╌⏈G㟝⓸
஄ㇵὤG⇨㟝㡴G㤵䚝㟝⓸G㦤ᶨ㢌G㢰⺴㢹⏼␘UG␭㇠㢌Gⷔ㏘䏬G㾨䇼⦐ἬSG㦹䚝G
㾨䇼⦐ἬSG⒤㢨䉤G㐐䏬G☥G㺐㐔䑄G㾨䇼⦐ἬGⵃG⬘⎨㛰㜄Gὤ㣠╌㛨G㢼⏈G⸨㫑ื
⮨㵹G㇠䚡㜄GḴ䚐G⇨㟝㡸G㍍㫴䚌㐔G䟸G㇠㟝䚨G㨰㐡㐐㝘U
㙼㤸ㇵ㢌G㩅㟈㇠䚡
Xஃ䑜≄㜄G㉘㾌䚔G㐐㜄⏈GYḧ㢌G⇌㇠⪰Gⶼᴼ㙸Gἔ䝉㡸G㣕㡰⮨㉐G㥉䞉䚌󰵡G㷨󰶅䚨G
㨰㐡㐐㝘UGἔ䝉㡸G㣕㫴G⯯䚌⮨G䑜≄G⇨⺴㜄GⱰ㢨G☘㛨ᴼGᴴ⏙㉥㢨G㢼㏩⏼␘U
Yஃ⸨㦨㡴Gὤ㣠═G㥉󰵾ⷈ㠸G⇨㜄㉐G䚨G㨰㐡㐐㝘UG❄GஇXW୅G㢨䚌㜄㉐G⸨㦨䚐G䟸㜄G㇠㟝䚔G
󰶒㟤㜄⏈Gㇵ㝜㜄㉐GZ㐐ᴸG㢨ㇵGⵝ㾌䚐G䟸G䋩㤸䚨G㨰㐡㐐㝘UG
Zஃⴴ㵝G㉘㾌䚌⮨G⇨⺴G⺴䖼㢌G㍌⮹㢨G␜㻉╔G㟤⥘ᴴG㢼㏩⏼␘U
[ஃ㇠㟝㐐G㨰㠸G㝜⓸⇌G㨰㠸G㏩⓸⏈Gὤ㣠═G㥉󰵾ⷈ㠸G⇨㜄㉐G㇠㟝䚨G㨰㐡㐐㝘U
\ஃ␘㢀ḰGᵍ㡴G䞌󰶒㜄㉐⏈G㇠㟝䚌㫴G⫼㐡㐐㝘U
ืG㝜⓸ⷴ䞈ᴴG㐠䚐Gḧ
ืG㏩⓸ᴴG⋆㙸G󰶅⦐ᴴG㈑ὬG㟤⥘ᴴG㢼⏈Gḧ
ืG㫸┍SG㻝󰵾㢌G㜵䛙㢨G䆤Gḧ
ืGⱰ㢨G䎴⏈Gḧ
ืGὤ⪸㢨G⌸㻐╌⏈Gḧ
]ஃ
⺸㫸㢨G⬂㡴G㣙㋀SG⺴㐑ᴴ㏘ᴴGⵐ㈑䚌⏈G㣙㋀SG㫵㇠ṅ㉔㜄G⊬㻐═G㣙㋀㜄㉐⏈G㇠㟝䚌㫴G
⫼㐡㐐㝘U
^ஃ␘⣽㢌G㥉㤸ὤᴴGⵐ㈑䚌⏈G䞌󰶒O㉥䝉G㣠⨀SGᴴ⨜SG㡔㷨G㣠⨀⪰G䑀㢨䘸Gⵌ㋕䚌⏈G󰶒㟤G
☥P㜄㉐G㇠㟝䚔G󰶒㟤㜄⏈G㥉㤸ὤGⵐ㈑㠄ḰG㥐䖼G⸬㷨㝴㢌Gᶤ⫠⪰G⛜㛨⡜⥘G㨰㐡㐐㝘U
_ஃ㥉󰵾G㢨㞬㢌G㤸㚉㡸G㢬ᴴ䚌⮨G⇨⺴㋀㣄ᴴG䑀Ṩ╔G㟤⥘ᴴG㢼㏩⏼␘U
`ஃ␜㣄㢌GἭ㉥㡴G㝘ⵤ㉔㢨G㛺⓸⦑G䚨G㨰㐡㐐㝘U
XWஃ⊬㢨㪼Gⵐ㈑㠄SG⊬㢨㪼ᴴGⵐ㈑╌⏈Gᵉ㤸㉔㡰⦐⺴䉤G㢹⥙㐔䝬㠄GὤὤSG㢹⥙㐔䝬㉔Gⵤ㉔G
ⵃG㥐䖼G⸬㷨⪰G⛜㛨⡜⥘GG㨰㐡㐐㝘U
XXஃ㚉㵝␜㣄⪰G㇠㟝䚌⏈G󰶒㟤㜄⏈G䚌⇌㢌G␜㣄㜄GYᵐᾀ㫴⬀G㇠㟝䚨G㨰㐡㐐㝘U
XYஃ
ⵤ㉔㡴GX␜㣄㜄GYᵐᾀ㫴⏈G㜤󰶅䚔G㍌G㢼㡰⇌SG㢨G󰶒㟤GYᵐ⏈Gᵍ㡴G㦹⪌㢌G㉔㡸G㇠㟝䚨G
㨰㐡㐐㝘UG
XZஃⵤ㉔㜄G㇠㟝䚌⏈G㤵㟝㤸㉔㡴Gὤ㣠═G㤵㤼䚐G㤸㉔㡸G㇠㟝䚨G㨰㐡㐐㝘U
㤵㟝㤸㉔aGh~nX_¥YYG␜㉔G䝭㡴G⁤㉔UGẠ⫠U
X[ஃ
㣅㛹㣄ᴴGⵈ⦐G㤸㠄㡸Gvmm䚔G㍌G㢼⓸⦑G㏘㠸㾌G䝭㡴G㉐䇫G⽀⤼㢨䆠⪰G㉘㾌䚌㜠G㤵㤼䚌󰵡G䖐㐐䚨G
㨰㐡㐐㝘U
X\ஃ㢹⥙␜㣄㜄㉐G㚱GX[}ᴴG㻐⥙╝⏼␘UG␘㢨㝘☐ᴴGㇱ㢹G㉘㾌═G㉰㉐⪰G㇠㟝䚨G㨰㐡㐐㝘U
X]ஃ㤸㠄㤸㚉㡴GWUX㸼G㢨⇨㜄G㥉󰵾㤸㚉㜄G⓸␠╔G㍌G㢼⓸⦑G㏘㠸㾌SG⫨⤼㢨G☥㢌G㥅㥄㡸G
ᶤ㸄G␜ⶼ㜄G㢬ᴴ䚨G㨰㐡㐐㝘UG㉐㉐䢼G㤸㚉㡸G㢬ᴴ䚌⮨G㤸㠄G⫠㉿㢨G㙼╌ᶤ⇌G㻐⥙G
㝘┍㣅㢨G㢰㛨⇔G㟤⥘ᴴG㢼㏩⏼␘U
X^ஃ㤸㠄㵜␜G㐐㜄⏈G㏘㠸㾌SG⫨⤼㢨G☥㢌G㥅㥄㡸Gᶤ㸄G␜ⶼ㜄G㵜␜䚨G㨰㐡㐐㝘UG㉐㉐䢼G
㤸㚉㡸G⇢㻈⮨G㻐⥙G㝘┍㣅G䝭㡴G⮈⯜⫠G㢨ㇵ㢨Gⵐ㈑䚔G㍌G㢼㏩⏼␘U
X_ஃˈㇵ㐐G⺼⤠㝘ὤGⵝ㐑O䋩㤸G㩅㢨⢰⓸G㉘㥉Gⷴ󰶒Gᴴ⏙Pˉ㡸G㵸䈑䚌ḔG㢼㛨G󰶙㐐G㩅㜄G
␘㢀ḰGᵍ㢨G㉘㥉ᵆ⪰Gⷴ󰶒䚌⮨G㻐⥙㢨Gvu╌⳴⦐G㨰㢌䚨G㨰㐡㐐㝘U
ˈ㢹⥙⯜☐aG|wˉG 㢰G󰶒㟤G󰶙㐐ᵆ҈㉘㥉ᵆ
ˈ㢹⥙⯜☐aGkv~uˉG 㢰G󰶒㟤G󰶒Ḱ㐐ᴸ҈㉘㥉ᵆO󰶙㐐ᵆdW㢨G╝⏼␘P
kv~uG⯜☐㢰G󰶒㟤G㉘㥉ᵆ⪰Gⷴ󰶒䚐G㛅㡴G󰶙㐐ᵆ㜄Gᴴ㇤Vᵄ㇤╝⏼␘UG㉘㥉ᵆdWG㢬G
ㇵ䈐㜄㉐㢌G┍㣅㡴G㐐Ἤ≄G㢹⥙═G㐐㥄㜄㉐G㻐⥙㢨Gvu╝⏼␘UG⫠㉿G㦤㣅㜄G㢌䚨G
㻐⥙㡴Gvmm╝⏼␘U
X`ஃ⸬㷨㢌G㞬㣙㡴G㡔ὤ㟝㥐O㐔⇌ืⷘ㥔G☥PSGᵉ㚀㾰⫠㉥GⵃGᵉ㇤Ɒ㫼㜄G㾜㐑╌ὤG⚀ⱬ㜄G
㇠㟝䚌㫴G⫼㐡㐐㝘U
YWஃ䖐㐐OsjkPᴴG㥉ㇵ㤵㡰⦐G┍㣅╌⏈㫴G䞉㢬䚨G㨰㐡㐐㝘UG㇠㟝䞌󰶒㜄G♤⢰㉐⏈GsjkSG
㍌㫴⺴䖼㢌G㜨䞈⪰G㚒␭󰵽G䖐㐐⺼⣽㢨Gⵐ㈑䚔G㍌G㢼㡰⳴⦐G㥉ὤG㥄ᶴGⵃGẄ䞌㡸G䚨G
㨰㐡㐐㝘U
YXஃⵝ㍌GḔⱨG䑜䇭㡴G㇠㟝䞌󰶒㜄G♤⢰G㜨䞈ื㍌㻉GⵃG󰶒䞈╌ὤG⚀ⱬ㜄G㥉ὤG㥄ᶴGⵃG
Ẅ䞌㡸G䚨G㨰㐡㐐㝘U
୔㥅㥄Gvu㜄G㢌䚨G┍㣅
୔䏬⣐㫴㏘䉤Gvu㜄G㢌䚨G┍㣅
㉰㉐G☥
୔䏬⣐㫴㏘䉤Gvu㜄G㢌䚨G┍㣅
wsjSG
㉰㉐G☥
ⱨ㤸㚉G㢹⥙GOuwuG㢹⥙P
ର㝘䘼G䂐⤽䉤଱ ର㤸㚉G㻐⥙଱ ର㡔㥅㥄G㢹⥙଱
󰶙㐐ᵆ
㉘㥉