One Forall URC 8080 User manual

INSTALLING THE BATTERIES
Note: After inserting the batteries, the LCD screen will
enter a test mode which tests each segment of the
LCD screen. This process will last for 10 seconds or
until any key is pressed, which ever occurs first.
Your A/V Producer requires four (4) new AAA
alkaline batteries. To install the batteries:
1On the back of the A/V
Producer , push down on
the tab and slide the
battery cover off.
2Match the + and - marks
on the batteries to the +
and - marks in the battery
case, then insert the
batteries.
3Slide the battery cover
back into place.
4Test the unit by pressing
POWER. If the batteries
are inserted correctly, the
red light will blink.
POWER
URC 8080
A/V Producer
User Manual

USING YOUR A/V PRODUCER
Features and Functions
The illustration below and the chart on the next two
pages describe the features and the functions of the
A/V Producer’s keypad. The following keys will
always have the same function, regardless of which
component you are controlling. For an explanation
of what each key does by component type, please
use the index at the rear of the manual (pages 45-57).
Feature Function
The MAGIC key is used to access
the menu and program your
A/VProducer .
TheTV,VCR,CBL,SAT,AMP,TUN,
CD, and AUX1 keys are used to
select the home entertainment
component you want to control. If
your component does not respond
when you press a key on the
remote control, press either the TV,
VCR,CBL,SAT,AMP,TUN,CD,
and AUX1 key to tell the remote
control which component you would
like to operate.
The HOMETHEATER key is used
to select the Home Theater mode of
the A/VProducer .
The ESC (Escape) key is used to
exit the LCD Screen menu.
The LITE key is used to turn ON
and OFF the A/V Producer’s
backlit keypad and LCD screen.
Press the LITE key once to turn
ON the backlight. The A/V
Producer’s backlight will stay on for
10 seconds after the last key press
and re-activates with the press of a
key. To de-activate the backlight,
press the LITE key again.
The POWER key controls power ON
and OFF.
The VOL + (Volume Up), VOL-
(Volume Down) and MUTE keys
control the volume the same as the
Volume Up and Down and Mute
keys on your original remote.
ESC
LITE
MAGIC
TV VCR
CBL
SAT
AMP
TUN
CD
AUX1
HOME THEATER
POWER
VOL-VOL+
MUTE
VOL-VOL+
CH-CH+
POWER
MUTE
SLEEP
AMP TUN TV CBL
CD VCR SAT AUX1
HOMETHEATER
SUR
SHIFT
ESC
CENTER
MENU
SELECT
PREV CH
DISP
PIP
FREEZE
SWAP
MOVIE
PIP
LITE
MAGIC
CLEAR
PROG
REAR
MENU+
MENU-
ENTER
AUD
SLOW- SLOW SLOW+
VID
TV/SAT
REW PL FF
REC STOP
EJECT X2
PAU

SETTING THE CLOCK
Feature Function (Cont.)
The CH + (Channel Up) and CH-
(Channel Down) keys change
channels the same as the Channel
Up and Down keys on your
original remote.
The AUD and VID macro keys
memorize up to 15 keystrokes that
can be accessed in sequence at the
press of a single key. These
keys are not mode specific.
The SHIFT key accesses advanced
features that are mapped under
the following keys: CENTER, MENU,
SELECT,MUTE, PREV CH,
PIP,REW,PLAY,FF,STOP and
PAUSE.
CH- CH+
AUD
VID
SHIFT
MAGIC
MENU-
SELECT
MENU-
SELECT
To set up the CLOCK/TIME on the display screen:
1Press and hold MAGIC until the
display screen changes from
[DEVICE and the TIME] to
[TIMED SEQ].
2Press the MENU - key twice, the
display will change to [CONFIGURE].
Press SELECT, the display will
change to [THEATR SEL].
3Press MENU - one time, the display
will change to [TIME SET]. Press
SELECT again.
4The display will change to [TIME]
and the first digit in the time will
blink. Enter either a 0or a 1, then
the next digit in the time will begin to
blink, continue entering the time
until all four digits of the time have
been set.
5After the time has been set, AM/PM
will then blink. Press MENU - to
toggle between AM and PM, once
AM or PM is selected, press
SELECT.
6The display will then change to the
day of the week (MON, TUES, WED,
THURS, FRI, SAT or SUN). Use
MENU - to toggle through the days
until the proper day of the week is
displayed on the screen, then press
SELECT. The display will return to
the [DEVICE and the TIME] screen
with the correct time on the display.
NOTE: After changing the batteries, you will have to reprogram
the clock.
0 - 9
x 2
SELECT
MENU-
MENU-
SELECT
Important: For a detailed explanation of what function
each key will perform by device type (TV, VCR, CBL,
etc.), please refer to pages 45 through 57.

To Quickly Set Up the A/V Producer to Operate
Your Home Entertainment Components
1Turn on all of the components that
you will be setting up.
2Press and release the TV key.
3Press and hold MAGIC until the
display screen changes from
[TV and the TIME] to [TIMED SEQ].
4Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SETUP]. Press SELECT. The
display will change to [TV}.].
5Enter the first TV code listed for your
brand in the “Set Up Codes forTVs”
on pages 10-12, then press
SELECT. Point the remote control at
the TV and press POWER. Your
Television should turn OFF. If your TV
does not turn OFF, enter the next
code in the code list then press
SELECT followed by POWER again.
Once yourTV turns OFF, press VCR.
You will now enter your VCR code.
6 Enter the first VCR code listed for
your brand in the “Set Up Codes for
VCRs” on pages 13-14, then press
SELECT. Point the remote control
at the VCR and press POWER. Your
VCR should turn OFF. If your VCR
does not turn OFF, enter the next
code in the code list then press
SELECT followed by POWER again.
Once yourVCR turns OFF, press
CBL. You will now enter your Cable
Box code.
QUICK SET UP 7 Continue to enter your codes as
illustrated in Steps 5 and 6 until the
A/V Producer is operating all of your
home entertainment components.
Once you have finished setting up
your components, press ESC to
return to the [DEVICE and TIME]
display.
If you would like to setup each of your
components individually, or if you purchase a
component after you have set up the A/V
Producer, see the "SETTING UP INDIVIDUAL
HOME ENTERTAINMENT COMPONENTS"
section on pages 10 - 22 in this manual.
Set Up Codes for TVs ....................... Pages 10 - 12
Set Up Codes for VCRs .................... Pages 13 - 14
Set Up Codes for Cable Boxes .................. Page 16
Set Up Codes for DSS and
Satellite Receivers............................... Page 17
Set Up Codes for Laser Disc Players......... Page 18
Set Up Codes for CD Players .................... Page 19
Set Up Codes for Tuner Receivers ............ Page 21
Set Up Codes for Amplifiers....................... Page 22
TV
MAGIC
MENU-
SELECT
SELECT
POWER
VCR
SELECT
POWER
CBL
ESC

Set Up Codes forTVs (cont.)
Broksonic 236, 463, 180,
003
Candle 030, 056, 186,
046
Carnivale 030
Carver 054 , 187, 170
CCE 217
Celebrity 000
Citizen 092, 060, 030,
056, 280, 186,
046, 039
Clairtone 185
Concerto 056
Contec 180, 185, 157,
158
Craig 180
Crown 180, 039
Curtis Mathes 047, 060, 054,
154, 030, 039
CXC 180
Daewoo 451, 092, 019,
039, 091
Daytron 056, 092
Dumont 017, 019
Dynatech 046
Electroband 000, 185
Electrohome 381, 389, 409
Emerson 463, 236, 180,
177, 179, 280,
178, 282, 154,
019, 185, 038,
039, 158, 181,
182, 183, 270
Envision 030
Fisher 154, 159
Fujitsu 179
Funai 171, 179, 180
Futuretech 180
GE 047, 451, 051,
021, 027, 282,
055, 178, 029,
135, 174, 279
Gibralter 017, 019, 030
Goldstar 056, 019, 030,
178, 001, 002,
032
Grunpy 179, 180
Hallmark 178, 179, 236,
019
Harvard 180, 236, 178,
179
Hitachi 145, 151, 056,
032, 038, 279,
409, 413
Infinity 054
Janeil 046
JBL 054
JCB 000
JVC 053, 036, 182,
169, 069, 160
Kawasho 158
Kaypani 052
KEC 180, 060
Kenwood 019, 030
Kloss 030, 046, 024
KMC 106
KTV 030, 039, 180,
183, 185, 217,
280
Logik 016, 180, 236
Luxman 056
LXI 047, 054, 148,
154, 156, 178
Magnasonic 054, 156, 179,
092, 030, 093,
019, 003
Magnavox 054, 096, 186,
030, 187, 020,
024, 028, 036,
386
Majestic 016, 017
Marantz 030, 054, 096,
187
Matsushita 250
Megatron 003, 145, 178
MEI 185, 051
Memorex 016, 056, 106,
150, 154, 178
MGA 150, 155, 178,
030, 019, 093
Midland 017, 032, 039,
047, 051, 135
Minutz 021
Mitsubishi 150, 155, 178,
030, 019, 093,
241
Motorola 093, 055, 054,
150, 051
MTC 060, 056, 030,
019, 185, 091
Multitech 180, 217, 019
NAD 156, 166, 178,
019
NEC 019, 030, 036,
056
Nikko 030, 092, 178
Noblex 430
Noshi 018
NTC 092
Onwa 180
Optimus 154, 166, 250,
463, 180, 179,
150, 165
Optonica 093, 165
Orion 236, 463, 180,
179
Panasonic 250, 051, 055,
054
Penney 047, 051, 060,
019, 018, 030,
156, 021, 027,
178, 003, 135,
039, 002, 032,
149
Philco 054, 096, 030,
019, 187, 020,
028
Philips 054, 096, 030,
019, 187, 020,
028
Pilot 019, 030, 039
Pioneer 166, 038
Portland 092, 019, 039
Prism 051, 055
Proscan 047
Proton 003, 052, 178
Pulsar 092, 017, 019
Quasar 250, 051, 055,
165
RadioShack 019, 030, 032,
039, 047, 056,
154, 165, 178,
180, 409
RCA 047, 018, 019,
029, 038, 090,
135, 147, 278,
093
SETTING UP INDIVIDUAL HOME
ENTERTAINMENT COMPONENTS
To Set Up Your Television
1Turn on yourTV.
2Press and release the TV key.
3Press and hold MAGIC until the
display screen changes from
[TV and the TIME] to [TIMED SEQ].
4Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
5Press SELECT and the display
screen will change to [TV].
6Enter the first TV code listed for your
brand in the “Set Up Codes forTVs”
on pages 10-12, then press SELECT.
Point the remote control at theTV
and press POWER. Your Television
should turn OFF. If your TV turns
OFF, press the ESC key to return the
display to [TV and the TIME]. If your
TV does not turn OFF, enter the next
code in the code list then press
SELECT followed by POWER again.
Once the correct code is entered,
press the ESC key to return the
display to [TV and the TIME].
For a detailed explanation of what function each key
will perform in the TV mode, please refer to page 45
in the index.
TV
MAGIC
MENU-
SELECT
SELECT
SELECT
POWER
ESC
Anam National 055
AOC 030, 019, 185,
080, 056, 003,
052
Archer 003
Audiovox 180, 003
Belcor 019, 030
Bell & Howell 016, 154, 179,
180
Bradford 180
Brockwood 019
A-Mark 003
Abex 032
Admiral 093, 016, 180,
165, 179
Adventura 046
Aiko 092
Akai 030, 056, 145,
151
Alleron 179, 183
Ambassador 177
Anam 180
Set Up Codes forTVs

6Enter the firstVCR code listed for
your brand in the “Set Up Codes for
VCRs” on pages 13-14, then press
SELECT. Point the remote control at
theVCR and press POWER or PLAY.
Your VCR should turn OFF or start to
play. If yourVCR turns OFF or starts
to play, press the ESC key to return
the display to [VCR and the TIME]. If
yourVCR does not turn OFF or start
to play, enter the next code in the
code list then press SELECT followed
by POWER or PLAY again. Once the
correct code is entered, press the
ESC key to return the display to [VCR
and the TIME].
For a detailed explanation of what function each key
will perform in the VCR mode, please refer to page
47 in the index.
Realistic 019, 030, 032,
039, 056, 154,
165, 178, 180
Rhapsody 183, 185
Runco 017, 030
Sampo 030, 032, 039,
052
Samsung 060, 019, 030,
032, 056, 178,
427, 482
Samsux 039
Sanyo 154, 159, 146
Scimitsu 019
Scotch 178
Scott 019, 178, 179,
180, 236
Sears 047, 054, 056,
146, 148, 149,
154, 156, 159,
171, 178, 179
Sharp 093, 039, 153,
157, 165, 386
Shogun 019
Signature 2000 016, 047, 054,
019
Simpson 186, 187, 030
Sony 000, 080
Soundesign 178, 179, 180,
186
Spectricon 003, 180, 030,
019, 056
Squareview 171
SSS 019, 180, 236
Starlite 180, 236, 019
Supre-Macy 046, 186
Supreme 000
Set Up Codes forTVs (cont.)
Sylvania 054, 096, 030,
187, 186, 020,
028
Symphonic 171, 179, 180
Tandy 093, 165, 054,
047, 039
Tatung 055, 051, 003
Technics 051, 250, 055
Technol Ace 179
Techwood 003, 051, 056
Teknika 092, 054, 060,
056, 019, 015,
180, 179, 186,
150, 039, 312
TMK 056, 177, 178,
236
Toshiba 156, 154, 060,
036, 149
Tosonic 185
Totevision 039
Trical 157
Universal 027, 021, 047
Vector Research 030
Victor 053
Vidikron 054, 242
Vidtech 019, 036, 178
Viking 046
Wards 154, 016, 096,
030, 056, 165,
019, 021, 027,
020, 178, 179,
080, 174, 028,
029
Zenith 017, 092, 016
Zonda 003
SELECT
or
POWER
PL
To Set Up Your VCR or TV/VCR Combinations
1Turn on your VCR and insert a tape.
2Press and release the VCR key.
3Press and hold MAGIC until the
display screen changes from
[VCR and theTIME] to [TIMED SEQ].
4Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
5Press SELECT and the display
screen will change to [VCR].
VCR
MAGIC
MENU-
SELECT
SELECT
Set Up Codes ForVCRs
Admiral 048
Adventura 000
Aiko 278
Aiwa 000
Akai 041, 049, 053,
061, 106
American High 035, 081
Asha 240
Audiovox 037, 038
Beaumark 240
Bell & Howell 104, 048, 046
Broksonic 184, 209, 121,
211, 295, 361,
002, 479
Calix 037
Candle 037, 038
Canon 035
Capehart 020
Carver 081
CCE 072, 278
Citizen 037, 278, 240,
035, 000
Colt 072
Craig 037, 047, 072,
240, 271
Curtis Mathes 035, 041, 060,
202
Cybernex 051, 240
Daewoo 020, 045, 278,
046
Daytron 020, 278
Dynatech 000
Electrohome 037, 240, 043
Electrophonic 037
Emerex 032
Emerson 184, 209, 479,
000, 002, 036,
037, 043, 061,
068, 121, 208,
211, 212, 278,
294, 295, 361
Fisher 047, 054, 066,
104, 046
Fuji 033, 035, 032,
034
Funai 000, 278, 072,
240
Garrard 000
GE 035, 060, 065,
202, 048
Go Video 232, 279, 240,
526
Goldstar 037, 038, 278
Gradiente 000
Harley Davidson 000
Harman/Kardon 038, 075
Harwood 068, 072
Havard 072
Headquarter 046
HI-Q 047
Hitachi 042, 000, 041,
065, 105, 166,
396
Jensen 041, 008, 067
JVC 008, 041, 067,
206
KEC 037, 278
Kenwood 038, 041, 067,
008
KLH 072
Kodak 035, 037
Lloyds 208, 072, 038
Logik 072
LXI 037, 035, 042,
046, 047, 054,
066, 104, 105
Magnasonic 240, 037, 278,
020, 072
Magnavox 035, 039, 081,
110, 149
Magnin 240
Marantz 035, 081
Marta 037
Matsushita 035, 162, 454,
081, 110
MEI 035
Memorex 000, 035, 037,
039, 046, 047,
048, 104, 240
MGA 043, 061
MGN Technology 240
Minolta 042, 105
Mitsubishi 043, 061, 067,
075, 173, 008,
048
ESC

Runco 039
Salora 075
Samsung 240, 045, 051,
053
Sanky 039, 048
Sansui 041, 067, 271,
209, 072, 002,
479, 008
Sanyo 104, 046, 047,
054, 240
Scott 043, 045, 121,
184, 210, 211,
212
Sears 035, 037, 042,
046, 047, 054,
066, 104, 105,
000
Sharp 048, 062
Shintom 072, 000, 240
Shogun 051, 240
Singer 072, 037, 240
Sony 032, 033, 034,
035
STS 042
Sylvania 000, 035, 043,
081, 110
Symphonic 000
Tatung 041, 067, 000
TEAC 000, 041
Technics 035, 162, 454
Teknika 000, 035, 037
TMK 036, 208, 240
Toshiba 043, 045, 060,
066, 210, 212,
366
Totevision 037, 240
Unitech 240
Vector 045
Vector Research 038, 040
Video Concepts 040, 045, 061
Videosonic 240, 000, 072
Wards 000, 035, 042,
047, 048, 060,
062, 072, 149,
212, 240, 202
XR-1000 000, 035, 072,
240
Yamaha 038
Zenith 039, 033, 034,
000
To Set Up Your Cable Box:
1Turn on your Cable Box.
2Press and release the CBL key.
3Press and hold MAGIC until the
display screen changes from
[CBL and theTIME] to [TIMED SEQ].
4Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
5Press SELECT and the display
screen will change to [CBL].
6Enter the first Cable Box code listed
for your brand in the “Set Up Codes
for Cable Boxes” on page 16, then
press SELECT. Point the remote
control at the Cable Box and press
POWER. Your Cable Box should
turn OFF. If your Cable Box turns
OFF, press the ESC key to return
the display to [CBL and the TIME]. If
your Cable Box does not turn OFF,
enter the next code in the code list
then press SELECT followed by
POWER again. Once the correct
code is entered, press the ESC key
to return the display to
[CBL and the TIME].
Note: If your original Scientific Atlanta remote control
does not have an “ON” key, press CH+ or one of the
digit keys on the A/V Producer to turn your Cable
Box on.
For a detailed explanation of what function each key
will perform in the Cable mode, please refer to page
45 in the index.
Set Up Codes ForVCRs (Cont.)
Motorola 035, 048
MTC 000, 240
Multitech 000, 072
NAD 104
NEC 038, 040, 041,
067, 104, 008
Nikko 037
Nikon 034
Noblex 240
Olympus 035
Optimus 037, 048, 104,
162, 454
Optonica 062
Orion 184, 209, 000,
479, 002, 036,
037, 043, 061,
068, 121, 028,
211, 212, 278,
294, 295, 361
Panasonic 035, 162, 254,
378, 454
Penney 035, 037, 038,
040, 042, 054,
240
Pentax 042, 065, 105
Philco 035, 081, 110
Philips 035, 062, 081,
110
Pilot 037
Pioneer 067, 008
Portland 020
Protec 072
Pulsar 039, 051, 240,
278
Quarter 046
Quartz 046
Quasar 035, 162, 454
RadioShack 000, 037, 035,
048
Radix 037
Randex 037
RCA 060, 202, 042,
149, 048, 065,
105, 106, 035
Realistic 000, 035, 037,
046, 047, 048,
062, 066, 104,
240
Ricoh 034, 035
Set Up Codes forTV/VCR Combinations
American High 035*
Broksonic 002, 294, 479
Colt 072
Curtis Mathes 035*
Daewoo 278
Emerson 002, 294, 479
Funai 000
GE 035*, 060*,
048*, 240
Harley Davidson 000
Hitachi 035*, 000
HQ 000
Lloyd's 000
Magnavox 000, 035*, 081*
Magnin 240
Memorex 037, 162*
MGA 240
Mitsubishi 048*
Orion 002, 294, 479
Panasonic 035*, 162*
Penney 035*, 240, 162*
Quasar 035*, 162*
RCA 060*, 035*,
048*
Sansui 000, 479
Sanyo 240
Sears 000, 037
Sony 032
Symphonic 000
Zenith 000, 037
CBL
MAGIC
MENU-
SELECT
SELECT
SELECT
POWER
ESC
Note*:
TV/VCRs working on 032 will need TV code 000 for volume control.
TV/VCRs working on 035 will need TV code 051 for volume control.
TV/VCRs working on 048 will need TV code 093 for volume control.
TV/VCRs working on 060 will need TV code 047 for volume control.
TV/VCRs working on 081 will need TV code 054 for volume control.
TV/VCRs working on 162 will need TV code 250 for volume control.
TV/VCRs working on 294 will need TV code 236 for volume control.

Philips 025, 027, 031,
153, 242, 290,
334
Pioneer 533, 144, 023,
260
Popular Mechanics 400
Prelude 770
Pulsar 000
RadioShack 797
RCA 021
Realistic 207
Recoton 400
Regal 020, 259, 273,
279
Regency 002
Rembrandt 011, 153
Runco 000
Samsung 040, 144
Scientific Atlanta 008, 477, 017,
006
Signal 015, 040
Signature 011
SL Marx 040
Sprucer 021, 307
Starcom 003, 015
Stargate 015, 040, 770
Starquest 015
Starsight 542
Sylvania 001
Tandy 258
TeleCaption 221
Teleview 040, 063
Texscan 001
Timeless 418
Tocom 012, 013
Toshiba 000
Tusa 015
TV86 063, 040
Unika 022, 153, 207
United Artists 007
United Cable 003
Universal 022, 077, 153,
191, 207
Videoway 250
Viewstar 027, 060, 063,
211, 258
Zenith 000, 525
Zentek 400
5Press SELECT and the display
screen will change to [SAT].
6Enter the first Satellite code listed
for your brand in the “Set Up Codes
for Satellites” on page 17, then
press SELECT. Point the remote
control at the Satellite and press
POWER. Your Satellite should turn
OFF. If your Satellite turns OFF,
press the ESC key to return the
display to [SAT and the TIME]. If
your Satellite does not turn OFF,
enter the next code in the code list
then press SELECT followed by
POWER again. Once the correct
code is entered, press the ESC key
to return the display to
[SAT and the TIME].
For a detailed explanation of what function each key
will perform in the Satellite mode, please refer to
page 55 in the index.
ABC 003, 014, 007,
008, 011, 017,
001, 013
Allegro 153, 000, 315,
191
Antronix 022, 207
Archer 022, 153, 207,
797
Cabletenna 022
Cableview 022
Century 153
Citizen 153, 315
Colour Voice 025, 031
Comband 232, 233
Comtronics Eagle 040, 060, 008
Contec 019
Eastern 002
Everquest 015, 040
Focus 400
Garrard 153
GC Electronics 207
GE 232, 233
Gemini 015, 057, 242
General Instrument 476, 276, 003,
014, 011
Goldstar 040, 144
Hamlin 009, 020, 034,
259, 273
Hitachi 011
Hytex 007
Infinity 770
Jasco 153, 315
Jerrold 003, 014, 476,
012, 011, 015,
024, 276
Macom 033
Magnavox 027, 334
Memorex 000
Movie Time 063, 156
Novaplex 618
Novavision 008, 017, 477
NSC 063, 156
Oak 007, 019
Omega 015
Panasonic 000, 021, 107
Panther 637
Paragon 000
Set Up Codes For Cable Boxes
SAT
MAGIC
MENU-
SELECT
SELECT
SELECT
POWER
ESC
To Set Up Your DSS or Satellite Receiver
1Turn on your DSS or Satellite
Receiver.
2Press and release the SAT key.
3Press and hold MAGIC until the
display screen changes from
[SAT and theTIME] to [TIMED SEQ].
4Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
Set Up Codes for DSS and Satellite Receivers
AlphaStar DSS 772
Amplica 072
Amway 043, 075
AstroIndustries 095
BSR 095
Cable Innovations 554, 555
Capetronic 095
Century 538
Channel Master 018, 212
Chaparral 053, 209, 216
Citoh 164
Conifer 004
Curtis Mathes 061, 072
Drake 018, 064, 149,
245
DXAntenna 041
Echostar 148, 159, 269,
280
Echostar DSS 775
General Instrument 050, 361, 554,
555
Hitachi DSS 819, 749
Homecable 238
HTS DSS 775
Hughes DSS 749, 819
Hytek 095
Intersat 043
IQ 210
Janeil 152
JerroldPrimestar 627
Jerrold 361
Legend 269
Macom 018, 050, 061
Magnavox DSS 724, 722
Memorex 269
Norsat 004
Panasonic 152
Panasonic DSS 701
Pansat 647
Philips 200
Philips DSS 724, 722
Pico 075
Primestar DSS 627
Prosat 158
RadioShack 554
Ramsey 075
RCADSS 566
Realistic 051, 052
Sony DSS 639
Star Trak 180, 421, 547
Strong 421
STS 041, 210
Toshiba 061, 082
Toshiba DSS 790
Uniden 052, 074, 076,
238, 296, 370,
554, 555
Uniden DSS 724, 722
Zenith 061, 064

1Turn on your CD Player and insert a
disc.
2Press and release the CD key.
3Press and hold MAGIC until the
display screen changes from
[CD and the TIME] to [TIMED SEQ].
4Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
5Press SELECT and the display
screen will change to [CD].
6Enter the first CD code listed for
your brand in the “Set Up Codes for
CD Players” on pages 19-20, then
press SELECT. Point the remote
control at the CD Player and press
PLAY. Your CD Player should start
to play your disc. If your CD Player
plays your disc, press the ESC key
to return the display to [CD and the
TIME]. If your CD Player does not
play your disc, enter the next code in
the code list then press SELECT
followed by PLAY again. Once the
correct code is entered, press the
ESC key to return the display to
[CD and the TIME].
For a detailed explanation of what function each key
will perform in the CD mode, please refer to page 56
in the index.
To Set UpYour CD Player:
Set Up Codes for CD Player
Acoustic Research 123
ADC 018, 033
Adcom 155, 234
Aiwa 012, 124, 157
Akai 156, 676
Alpine 341
Audio Alchemy 194
Audio-Technica 170
BSR 194, 245
Burmester 420
California Audio Lab 029
Capetronic 237
Carrera 194
Carver 157, 179, 299,
365, 437
Craig 615
Crown 122
DAK 245
Denon 003, 034
DKK 000
Emerson 155, 164, 305,
469
Fisher 048, 088, 174,
179, 342
Garrard 245, 280, 393,
420, 425, 633
GE 009, 334
Genexxa 032, 164, 305
Goldstar 030, 417, 525
Gradiente 558
Harman/Kardon 108, 426
Hitachi 032, 139, 155
1Turn on your Laser Disc Player and
insert a disc.
2Press and release the AUX 1 key.
3Press and hold MAGIC until the
display screen changes from
[LDP and theTIME] to [TIMED SEQ].
4Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
5Press SELECT and the display
screen will change to [LDP].
6Enter the first Laser Disc code listed
for your brand in the “Set Up Codes
for Laser Disc Players” on page 16,
then press SELECT. Point the
remote control at the Laser Disc
Player and press POWER or PLAY.
Your Laser Disc Player should turn
OFF or play your disc. If your Laser
Disc Player turns OFF or plays your
disc, press the ESC key to return the
display to [LDP and the TIME]. If
your Laser Disc Player does not
turn OFF or play your disc, enter the
next code in the code list then press
SELECT followed by POWER or
PLAY again. Once the correct code
is entered, press the ESC key to
return the display to
[LDP and the TIME].
For a detailed explanation of what function each key
will perform in the AUX1 mode, please refer to page
50 in this index.
To Set UpYour Laser Disc Player:
Aiwa 203
Carver 064, 194, 323
Denon 172, 241
Disco Vision 023
Funai 203
Hitachi 023
Magnavox 194, 217, 241
Marantz 064, 194
Mitsubishi 059
NAD 059
NEC 286
Panasonic 204
Philips 064, 194
Pioneer 059, 023
Quasar 204
RCA 128, 351
Realistic 203
Samsung 323
Sega 023
Sony 193, 201, 270
Theta Digital 194
Yamaha 217
Set Up Codes for Laser Disc Players
or
AUX1
MAGIC
MENU-
SELECT
SELECT
SELECT
POWER
PL
MAGIC
CD
MENU-
SELECT
SELECT
SELECT
PL
ESC
ESC

ADC 531
Adcom 616
Admiral 182
Aiwa 121, 125, 158,
189, 405
Akai 076, 224
Bose 639
Capetronic 531
Carver 008, 042, 189,
360, 412
Casio 195, 201
Clarinette 195
Curtis Mathes 201
Denon 004, 273, 771,
386
Emerson 255, 424
Fisher 042, 219, 360
Garrard 281, 424, 440,
463
Goldstar 281, 386
Harman/Kardon 110
Hitachi 386
Inkel 062
JVC 074, 464
Kenwood 027, 077, 186,
313, 314
Koss 255, 424
Lloyd 195
Luxman 166
LXI 181
Magnavox 128, 189, 195,
531
Marantz 189, 006, 039,
128, 200, 412
MCS 039, 201, 346
Modulaire 195
NAD 320
Nakamichi 347
NEC 235
Onkyo 135, 100, 119,
380
Optimus 080, 177, 181,
186, 219, 440,
531, 670
Panasonic 039, 518, 309
Penney 195, 201
Philips 189, 412
Pioneer 014, 080, 150,
289, 531, 630
Quasar 039
RCA 054, 346, 360,
530, 531
Realistic 163, 181, 182,
195
Sansui 189, 346
Sanyo 219
Scott 105, 163, 322,
390
Sears 201
Sharp 186
Sherwood 062, 491, 502
Sonic 281
Sony 158, 238
Soundesign 670
Symphonic 182
TEAC 463, 163, 298,
387
Technics 039, 208, 309,
518
Techwood 281
Victor 074
Wards 014, 042, 054,
080, 158, 189
Yamaha 176, 081, 082,
186
Yorx 195
Zenith 281
Proton 152, 157
QED 157
Quasar 029
RCA 009, 053, 155,
179, 305, 764
Realistic 155, 164, 175,
179, 180, 237,
420
Rotel 157, 420
SAE 157
Samsung 524
Sansui 157, 202, 216,
305
Sanyo 087, 179
Schneider 560
Scott 155, 164, 305
Sears 305
Sharp 037, 180, 262,
265
Sherwood 065, 114, 180,
196, 426
Shure 043
Signature 108
Signature 2000 108
Sony 000, 185, 490,
604, 605, 727
Soundesign 145, 425
STS 018
Symphonic 183
Tascam 420
TEAC 016, 045, 153,
174, 180, 183,
378, 393, 420
Technics 029, 207, 303
Toshiba 019, 299
Vector Research 033, 194, 417
Victor 072
Wards 108
Yamaha 036, 170, 187,
261
Yorx 461
Zenith 615
Set Up Codes for CD Player (Cont.)
Inkel 065
JVC 072, 655, 658
Kenwood 028, 037, 048,
190, 337, 338,
339, 340, 523
Kodak 287
Koss 734
Krell 157
Kyocera 018
Luxman 093, 149, 327
LXI 305
Magnavox 038, 129, 157,
526
Marantz 005, 029, 038,
157, 180, 435
McIntosh 287
MCS 029, 043, 345,
454
MGA 083
Mission 157
Mitsubishi 083, 098
MTC 420
NAD 019, 299
Nakamichi 147
NEC 043, 130, 234
Nikko 164, 169, 170,
174, 525
NSM 157
Onkyo 101, 102, 138,
381
Optimus 000, 032, 037,
087, 175, 179,
194, 196, 280,
305, 342, 420,
426, 437, 468,
536
Panasonic 029, 367, 388,
752
Parasound 194
Philco 603, 734
Philips 157, 274, 287
Pioneer 032, 244, 305,
468, 551
To Set UpYourTuner/Receiver
1Turn on your Tuner/Receiver.
2Press and release the TUN key.
3Press and hold MAGIC until the
display screen changes from
[TUN and theTIME] to [TIMED SEQ].
4Press the MENU - key one time.
The display screen will change to
[CODE SET UP]. Press SELECT.
The display will change to
[DEV SET UP].
5Press SELECT and the display
screen will change to [TUNER].
TUN
MAGIC
MENU-
SELECT
SELECT
Set Up Codes forTuner/Receivers
SELECT
6Enter the first Tuner code listed for
your brand in the “Set Up Codes for
Tuner/Receivers” on page 21, then
press SELECT. Point the remote
control at the Tuner/Receiver and
press POWER. Your Tuner/Receiver
should turn OFF. If your Tuner/
Receiver turns OFF, press the ESC
key to return the display to
[TUN and the TIME]. If your Tuner/
Receiver does not turn OFF, enter
the next code in the code list then
press SELECT followed by POWER
again. Once the correct code is
entered, press the ESC key to return
the display to [TUN and theTIME].
For a detailed explanation of what function each key
will perform in the Tuner mode, please refer to page
54 in the index.
POWER
ESC