One Forall URC-9910 User manual

IR/RF LCD 8-DEVICE WITH LEARNING
UNIVERSAL REMOTE CONTROL (URC-9910)
User’s Guide

TABLE OF CONTENTS
Introduction.... .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..... 3
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting The Clock... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features And Functions .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Key Charts. .. ... .. ... .. ... .. .. ... .. ... .. .. ... .. ... .. ... .. .. ... .. ... ... .. . .7
Setting Up Your Componenets.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .10
Programming TV/VCR Combo Control .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 12
Manufacturer’s Codes.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .14
Setup Codes for TVs . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. . ...14
Setup Codes for VCRs. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . ..17
Setup Codes for TV/VCR Combos .. .. .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . 19
Setup Codes for DVD Players . . .. .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . 20
Setup Codes for Cable Converters . . .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .21
Setup Codes for Satellite Receivers . .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. 22
Setup Codes for CD Players . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. 22
Setup Codes for Audio Amplifiers. .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. . .23
Setup Codes for Audio Cassette Decks. . .. . .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . 24
Setup Codes for Audio Receivers . .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . 24
Setup Codes for Audio Turntables . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. 25
Setup Codes for Misc. Audio Services . . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .25
Setup Codes for DAT Recorders . .. .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . 25
Setup Codes for LD Players. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .25
Setup Codes for Home Automation. .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .25
Setup Codes for Video Accessories.. .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. 26
Searching For Your Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using Learning .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 29
Programming A Learning Key. .. .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. 29
Deleting A Function From A Learning Key. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. 31
Using Volume Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Programming Volume Lock.. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .32
Programming Volume Unlock .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . 33
Using Macros. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 34
Programming A Favorite Channel. .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . 34
Programming A Master Power Key With Instant Channel Selection. . .. .. . .. .. . .. . .. .. 35
Clearing A Macro . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. . ... 36
Re-Assigning Device Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Using Keymover .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 38
Programming Keymover . .. . .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. . .. 38
Restoring Keymover . . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. .39
Using Channel Scan ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Programming Favorite Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Using The Home Theater Mode.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Control Organization. . .. . .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. . .. ..43
Programming The Home Theater Mode . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .44
Operating The Home Theater Mode . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. 47
Using Commercial Skip .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .48
Programming Commercial Skip . .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .48
Operating Commercial Skip . .. . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. 49
Restoring Factory Default Settings.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
About Upgrading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Using The IR/RF Command Center. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 52
Setting Up The IR/RF Command Center.. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . .. .. . .. 52
Adding The IR Signal Extension Cord . .. . .. .. . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. 53
Optimizing IR/RF Command Center Reception . .. .. . .. .. . .. .. . .. .. . .. . .. .. . .. .. . 54
Specifications.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..54
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Error Messages.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Compliance With FCC Rules And Regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Key Index.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . 58
Limited Warranty .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Additional Information . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .78
2

INTRODUCTION
TheOneForAllIR/RFLCD8-DeviceWithLearningUniversal
RemoteControl(URC-9910)isourlatesthigh-performance
universalremotecontrol.Itisdesignedtooperateuptoeighthome
entertainmentdevices,includingTV,video,andaudiocomponents.
Moreover,thisremotecontrolcontainssophisticatedtechnologythat
willallowyoutoconvenientlyconsolidatetheclutterof allof the
originalremotecontrolsusedinyourhomeentertainmentsystem.
It’spackedwitheasy-to-usefeaturessuchas:
• AdvancedLiquidCrystalDisplay(LCD)with15alphanumeric
characters,real-timeclock,andiconsforconstantvisualfeedback
of operationsandprogrammingsequences
• AuniqueHome Theater modethatcombinesdifferentdevice
controlsunderonemodeforoperatingconvenience
• Threemacrokeysforinstantactivationof favoritekeysequences
• Fourlearningkeystocaptureuniquefunctionsfromyour
devices’original remotecontrols
•Key Mover forcopying keys from one device toanother,ortoa
differentpositioninthesamemode
•CodeSearchtohelpyouprogramdevicecodeswithoutusingthe
codelist(startingonpage14) orforbrandsormodelsnotlisted
•FavoriteChannelScanforeasy channel surfing
• Modereassignmenttocontrolduplicatetypesof devices
•Volume Lock toassign volume controlsto individualdevices orto
one global device
•CommercialSkipfeatureallowsyoutochannelsurf during
commercialinterruptionsof yourfavoriteprograms
• IncludesIR/RFCommandCentertoextendthe remotecontrol’s
signalrange
• Pre-programmeddatabasewiththeworld’slargestandmost
efficientgroupof infraredcodesinsuresdevicecompatibility
• Internalmodemforupgradingdevicecodesoverthetelephone
• Alowbatteryicontonotifyyouwhenbatteriesaregettinglow
• Backlightingfeaturetoaidoperationinlowambientlight
TheOneForAllIR/RFLCD8-DeviceWithLearningUniversal
RemoteControl(URC-9910)requiresfour(4)newAAAalkaline
batteries(notincluded)andeasyprogrammingtocontrolyour
devices.Forbestresults,pleasereadandperformallinstructions
listed here.Also,keep these instructions for future reference.
3

INSTALLING BATTERIES
1. Onthebackof theURC-9910remotecontrol,push
thetabandlift off thebatterycover.
2. Obtainfour(4)newAAAalkalinebatteries.Match
the+and–marksonthebatteriestothe+and–
marksinthecase,andtheninsertthenewbatteries.
3. Alignthecoverkeywiththecaseopeningand
replacethecoveruntilitlocks.
4. If batteriesareinsertedcorrectly,theentireLCD
willturn on.After5secondsof inactivity,theremote
controlwill turnitself off toconservebatterylife.
5. PerformthestepsinSettingTheClock(onthenext
page)tosetthecorrecttime.
NOTE:Whenabatteryiconappearsinthedisplay(seepage7, Key Charts ,
LCD),thebatteriesarelow.SimplyreplacethemandtheURC-9910remote
controlwillberestoredtofull functionality,completewithyour favoritesettings.
4
❶
❸
❷

SETTING THE CLOCK
1. OntheURC-9910remotecontrol,pressandhold
SETuntilyouseethedisplaychangefromthedefault
device and time to[CODE SET].
NOTE:Defaultvaluesfordevice,itscode,andtimeare
shownabove.Yourremotecontrolsettingsmaybedifferent.
NOTE:If youwishto exittheprogrammingmodeatany
time,press
EXIT once.Youwillsee an [EXIT] messageasthe
remotecontrolreturnstonormaloperation.
NOTE:If youseean
[INVALID] message,youhaveinadver-
tentlypressedanincorrectkey.Simplynoteyourerrorand
continueprogramming.
2. Pressthe▲keyfivetimesuntilyouseethedisplay
change to[CLOCK SET].
(x 5)
NOTE:If yougo past [CLOCK SET] ,pressthe ▼ keyoneor
moretimestoreturntoit.
3. PressSELECT oncetobeginprogramming.Youwill
seethedisplaychangetothecurrenttime.
4. Pressthe▲keyoneormoretimesuntilyouseethe
desired hour(a.m.orp.m.).
5. Pressthe▼keyoneormoretimesuntilyouseethe
desired minute.
6. Oncethetimeiscorrectlyset,pressSELECTonce to
acceptthevalues.Thedisplaywillconfirmyour
entrywith[SUCCESS] andthen[EXIT SETUP].
TheURC-9910remotecontrolwill returnto
normal operation.
SELECT
SELECT
5

FEATURES AND FUNCTIONS
UsetheillustrationbelowtolocatefeaturesontheURC-9910remote
controland thenstudytheKeyCharts(onthenextthreepages)to
learnhowtheyfunction.
6
SELECT
S
U
R
R
O
U
N
D
S
O
U
N
D

Key Charts TheLED(redlight)blinkstoshowthatthe
remotecontrolisworkingandsendingsignals.
TheLCD(LiquidCrystalDisplay)
provides15alphanumericcharac-
tersthatdisplaystatus messages
during remote control operation
andprogramming.Also,oneor
moreiconsappearintheLCD to
indicatethefollowingconditions:
or MorningorAfternoonTime
LowBattery
IRSignalTransmission
Press TV,VCR,DVD,AUX,SAT,CBL,
RCVR/AMP,orCDoncetoselect a
desiredhomeentertainment
device tocontrol.
Afterprogramming,pressHOME
THEATERoncetoselectthehome
theatermode.(SeeUsingTheHome
TheaterModeonpage43.)
Press POWER onceto turn onoroff the
selected device.
Usethecursorkeys(▲,▼,or)tomove
thecursorintheprogramguideandmenu
screens.UseSELECT tochooseoptionsfrom
yourselecteddevice’smenuorguide.
IntheCDmode,useSELECT toselecta
compactdisc.Use ▲(or▼)toselectthenext
(orprevious)CD.Use (or )toselectthe
next(orprevious)track.
IntheRCVR/AMPmode,useSELECT to
setthesurroundsound.Use▲(or▼)to
adjustthevolumehigher(orlower).Use
(or )toadjustthebalanceleft(orright).
Press MENU once to displayyourselected
device’s main menu.
UseGUIDE todisplay yourselecteddevice’s
programguideorsetupmenu.
continuedonnextpage...
▲
▲
▲
▲
▲
▲
SELECT
S
U
R
R
O
U
N
D
S
O
U
N
D
7

FEATURES AND FUNCTIONS
Key Charts (continued)
UseEXIT toexitfromyourselecteddevice’s
guideormenu.
UseINFO todisplaythecurrentchanneland
programinformation.
UseVOL+ (orVOL-)toraise(orlower)the
audio volume.
Press MUTE onceto turnthe audio off
oron.
IntheTV,VCR,DVD,SAT,andCBLmodes,
useFAV toscanfavoritechannelsand/orall
channels.(SeeUsingChannelScanand
ProgrammingFavoriteChannelScanonpage
41.)
UseCH+ (orCH-)toselectthenexthigher(or
lower)channel.
Press PREV oncetorecallthelast-viewed
channelandtopagebackonescreenonthe
mainmenu.
IntheCDmode,usePREV to turnrandom
playonor off.
IntheRCVR/AMPmode,usePREV toselect
thereceiverband.
Usethekeypad(1~9and0)to
directlyselectchannels(e.g.,009 or
031).
IntheRCVR/AMPmode,usethe
keypad (1~9and0)toselectaudio
sources1through10.
Press ENTER once afterenteringthechannel
numbersonsomeTVs.
IntheCDmode,useENTER to add10 tothe
digitentry(e.g.,ENTER and7is17).
UseTV/VID to switchtheTV’sinputtoview
TVorvideoprograms.
8

Usethetransportkeystocontrolyour
VCR,DVDorCDplayer,orVOD(Video
OnDemand)if availableonyourcable
orsatelliteservice.
TorecordaVCRprogram,pressREC
twice.
UseSLEEP to activateyourdevice’ssleep
timer(notavailableforalldevices).
Afterprogramming,pressM1~M3 onceto
runadesiredmacro(seeUsingMacroson
page34).
Afterprogramming,pressL1~L4
oncetoactivatea learned function.
(SeeUsingLearningonpage30.)
UsePIP toswitchthePicture-In-Picture
featureonoroff (if availableonyourTV).
UseMOVE tomovethewindowpicture
todifferentpositionsinthemainpicture.
UseSWAPtoswitchimagesandsound
betweenthemainandwindowpictures.
Afterprogramming,useCOM SKIP to skip
commercialsonselecteddevices(i.e.,TV,VCR,
DVD,CBL,andSAT).(SeeUsingCommercial
Skiponpage48.)
Use toturnonoroff thekeybacklight.
Whenthisfeatureisactivated,keyswill
remainbacklitfor5secondsafterthelastkey
press.Inthesetupmode,backlighting
willremainonfor30seconds.
UseSET forallprogrammingsequences.
9

SETTING UP YOUR COMPONENTS
TheURC-9910remotecontrolispreprogrammedatthefactoryto
operateanRCATVandVCR,aMotorola(GI)cableconverter,anRCA
satellitereceiver,aPioneerCDplayer,aToshibaDVDplayer,aPioneer
audioreceiver/amplifier,andaOneForAllhomeautomationdevice.
Tocontroldevicesotherthanthedefaultbrands,performthefollow-
ingstepsandrepeatthemasneededforeachdevicetobepro-
grammed;otherwiseskipthissection:
NOTE:ForTV/VCRCombocontrol,see“ProgrammingTV/VCRCombo
Control”onpage12.
1. Turnonadevice(e.g.,VCRorDVDplayer)and,if
applicable, insertmedia(e.g.,cassetteordisc).
NOTE:Pleasereadsteps2through8completelybefore
proceeding.Highlightorwrite downthecodesanddevice
youwishtoprogrambeforestarting step2.
2. OntheURC-9910remotecontrol,pressandhold
SETuntilyouseethedisplaychangefromthecur-
rentdeviceandtimeto[CODE SET].
NOTE:Thedevice,itscode,andtimeareexamples.Your
remotecontrolsettingsmaybedifferent.
NOTE:Toexitprogrammingatanytime,press
EXIT onceor
allow30secondsof inactivityto lapse.Youwillsee
[EXIT
SETUP]
astheremotecontrolreturnstonormaloperation.
NOTE:
[INVALID] meansyouhaveinadvertentlypressedan
incorrectkey.Noteyourerrorandcontinueprogramming.
3. PressSELECT oncetobeginprogramming.Youwill
seethedisplaychangetothelast-selecteddevice
anditscurrentcode(e.g.,TVand0051).
4. Pressadesireddevicekeyonce(e.g.,VCR).Youwill
seethedisplaychangetothedesireddeviceandits
currentcode(e.g.,VCR and0035).
NOTE:Usethe AUX keytoprogramcontrolof home
automationdevices,videoaccessories,audioservices,and
otheraudioorvideodevices.Alternately,usethe
AUX keyto
programcontrolof aseconddevicetype (e.g.,asecondVCR;
see“Re-assigningDeviceKeys” onpage37).
5. UsetheManufacturer’sCodes(startingonpage14)
tolocate thetypeof deviceandbrand name.Then
usethekeypadtoenterthefirstfour-digitcodefor
yourdeviceandpressSELECTonce.
SELECT
SELECT
10

Forexample,toenterthefirstGEVCRcode(on
page17),press0twice,6 once,0once,andthen
SELECTonce.
If thecodeis enteredcorrectly,youwill seethe
[SUCCESS]message.
6. PressEXIT toexittheprogrammingmode.Youwill
seean[EXIT SETUP]messageastheURC-9910
remotecontrolreturnstonormaloperation.
7. Toverifythecodeworks,aimtheURC-9910remote
controlatthedesireddevice,pressitsdevicekey
onceandthenpressPOWERonce.Thedevice should
turnoff.If itdoesnot respond,repeatsteps 2
through6,tryingeachcodeforyourbranduntilyou
findonethatworks.If itstilldoesnotwork,try
SearchingForYourCodeonpage27.
NOTE:If thedevicedoesnothavea POWER key,pressthe
(
Play )key.
8. Repeatsteps1through7foreachdeviceyouwant
tocontrol.Forfuturereference,writedowneach
workingdevicecodeintheboxesbelow:
TVCode:
VCRCode:
DVDCode:
SATCode:
CBLCode:
RCVR/AMP
Code:
CDCode:
AUXCode:
Aux.Device
Type:________________________________
11

PROGRAMMING TV/VCR COMBO CONTROL
PerformthefollowinginstructionstocontrolaTV/VCRCombo:
1. TurnontheTV/VCRComboandinsertavideo
cassette.
NOTE:Pleasereadsteps2through9completelybeforepro-
ceeding.Highlightorwritedown the codes anddeviceyou
wishtoprogrambeforestartingstep2.
2. OntheURC-9910remotecontrol,pressandhold
SETuntilyouseethedisplaychangefromthecur-
rentdeviceandtimeto[CODE SET].
NOTE:Thedevice,itscode,andtimeareexamples.Your
remotecontrolsettingsmaybedifferent.
NOTE:Toexitprogrammingatanytime,press
EXIT onceor
allow30secondsof inactivityto lapse.Youwillsee
[EXIT
SETUP]
astheremotecontrolreturnstonormaloperation.
NOTE:
[INVALID] meansyouhaveinadvertentlypressedan
incorrectkey.Noteyourerrorandcontinueprogramming.
3. PressSELECT oncetobeginprogramming.Youwill
seethedisplaychangetothelast-selecteddevice
anditscurrentcode(e.g.,TVand0051)
4. PressVCR once.Youwillsee thedisplaychangeto
[VCR]anditscurrentcode.
5. UsetheSetupCodesForTV/VCRCombos(on
page19)tolocatethetypeof deviceandbrand
name.Thenusethekeypadtoenterthefirstfour-
digitcodeforyourdeviceandpressSELECTonce.
Forexample,toenterthefirstSonyTV/VCRCombo
codeonpage23,press0fourtimesandthen
SELECTonce.
If thecodeis enteredcorrectly,youwill seethe
[SUCCESS]message.
NOTE:If yourTV/VCRCombohas aseparateTV code,you
willalsoneedtoperformstep6.
SELECT
SELECT
12

6. (Optional)Skipthisstepif yourTV/VCRCombo
doesnothaveaseparateTVcode.Otherwise,press
TVonce.Youwillseethedisplaychangeto[TV]and
itscurrentcode.
UsethekeypadtoentertheseparateTVcodefor
yourdevice.
7. PressEXIT toexittheprogrammingmode.Youwill
see[EXIT SETUP]astheURC-9910remotecontrol
returnstonormaloperation.
8. Toverifythecodeworks,aimtheURC-9910remote
controlatthedesireddevice,pressVCR onceand
thenpressPOWER once.TheTV/VCRCombo
shouldturnoff. If itdoes notrespond,repeatsteps2
through8,tryingeachcodeforyourbranduntilyou
findonethatworks.If itstilldoesnotwork,try
SearchingForYourCodeonpage27.
NOTE:If thedevicedoesnothavea POWER key,pressthe
(
Play )key.
NOTE:ForVCR/TVCombosprogrammedwithseparateTV
codes,TVvolumeiscontrolledby pressingVCRfirstand
thenTV.Afterthat,use
VOL+ (or VOL- )toraise(orlower)
theTVvolume.Forotheralternativesoncontrollingvolume
keys,see“ChangingVolumeLock” onpage32or“Using
Keymover”onpage38.
9. Forfuturereference,writedowntheworking
TV/VCRcombocodeinthebelowboxes:
TV/VCRCode:
TVCode
(if used):
13

SEARCHING FOR YOUR CODE
If yourdevicedoesnotrespondtothe URC-9910remotecontrol
aftertryingall codeslistedforyourbrand,orif yourbrandis not
listedatall,trymanuallysearchingforyourcode.
Forexample,tomanuallysearchforacodeforyourTV:
1. TurnontheTV.
2. OntheURC-9910remotecontrol,pressandhold
SETuntilyouseethedisplaychangefromthe
currentdeviceandtimeto[CODE SET].
NOTE:Thedevice,itscode,andtimeareexamples.Your
remotecontrolsettingsmaybedifferent.
NOTE:Toexitprogrammingatanytime,press
EXIT onceor
allow30secondsof inactivityto lapse.Youwillsee
[EXIT
SETUP]
astheremotecontrolreturnstonormaloperation.
NOTE:
[INVALID] meansyouhaveinadvertentlypressedan
incorrectkey.Noteyourerrorandcontinueprogramming.
3. Pressthe▼keyonceuntilyouseethedisplay
change to [MAN SEARCH].
NOTE:If yougo past [MAN SEARCH] ,pressthe ▲ keyoneor
moretimestoreturntoit.
4. PressSELECT oncetobeginprogramming.Youwill
seethedisplaychangetothelast-selecteddevice
anditscode(e.g.,VCRand0035).
5. Pressadesireddevicekeyonce(e.g.,TV).Youwill
seethedisplaychangetothedesireddeviceandthe
firstcodeinthemanualsearchlist(e.g.,TV and
0047).
6. AimtheURC-9910remotecontrolatthedevice
(e.g.,TV)andpressSELECT once.Youwillseethe
LED(redlight)blinkandthe (IR)iconflash
indicatingIRcodesarebeingtransmitted.
continuedonnextpage...
SELECT
SELECT
27

SEARCHING FOR YOUR CODE (continued)
NOTE:Inthemanualsearchmode,theURC-9910 remote
controlwillsendIRcodesfromitslibrarytotheselected
device,startingwiththemostpopularcodefirst.
7. If thedevice(e.g.,TV)turnedoff,skiptothenext
step.If itdidnotturnoff,aimtheURC-9910remote
controlatthedevice(e.g.,TV)andpressthe▲key
oncetoadvancethemanualsearchtothenextcode
(e.g.,TVand0054).Againyouwillsee theLED(red
light)blinkandthe (IR)iconflash.
Repeatthisstepasoftenasneededuntilyoufinda
codethatturnsoff thedevice.
8. Tosavetheworkingcode,pressSELECT once.The
displaywillconfirmyourentrywith[SUCCESS]and
then[EXIT SETUP].
TheURC-9910remotecontrolwill returnto
normal operation.
NOTE:Forfuture reference,writedowntheworkingdevice
codeintheappropriateboxesonpage11.
9. Toperformamanualcodesearchforanother
device,repeatsteps1through8,butthistime(in
step5)substitutetheappropriatedevicekey forthe
deviceyouaresearchingfor.
NOTE:If youhavenotfounda workingdevicecodeaftertryingtheabove
procedure,pleasecontactourcustomerservicecentertoupgradeyour
OneForAllIR/RFLCD8-DeviceWithLearningUniversalRemoteControl
(URC-9910).See“AboutUpgrading”onpage51.
SELECT
28

USING LEARNING
Programthelearningkeys(L1~L4)toaddfunctionsthatare
uniquetoyourhomeentertainmentdevices(e.g.,VCRTrackingUp
orDown).However,therearesomeconsiderations:
• Youroriginalremotecontrolmustbeinworkingorderforthe
learningfeaturetoworkproperly.
• Learnedkeysaremodespecific,soeachonecanstoreaunique
functionfor eachmode.
• Learnedkeyscanbeusedinmacros(seeUsingMacrosonpage34).
• Although dedicatedkeys(L1~L4) areprovided forstoring
learnedfunctions,youcanalsouseanykey(exceptkeysfor
devicesandprogramming)forlearning.However,usingthemas
learnedkeyswilloverwritetheiroriginalfunctions.
• Foroptimumlearning,avoidhigh levelsof ambientlightsuchas
naturalsunlightorenergy-efficientfluorescentlights.
NOTE:Pleasehaveyouroriginal remotecontrolshandybeforeprogramming
learning.Besuretopress eachkeywithin5 secondsof thepreviousentry.
If not,the URC-9910 remotecontrolwill exitthe programmingmode.
Programming A Learning Key
1. OntheURC-9910remotecontrol,pressandhold
SETuntilyouseethedisplaychangefromthecur-
rentdeviceandtimeto[CODE SET].
NOTE:Thedevice,itscode,andtimeareexamples.Your
remotecontrolsettingsmaybedifferent.
NOTE:Toexitprogrammingatanytime,press
EXIT onceor
allow30secondsof inactivityto lapse.Youwillsee
[EXIT
SETUP]
astheremotecontrolreturnstonormaloperation.
NOTE:
[INVALID] meansyouhaveinadvertentlypressedan
incorrectkey.Noteyourerrorandcontinueprogramming.
2. Pressthe▼keytwiceuntilyouseethedisplay
changesto [IR LEARN].
(x 2)
NOTE:If yougo past [IR LEARN] ,pressthe ▲ keyoneor
moretimestoreturntoit.
3. PressSELECT oncetobeginprogramming.Youwill
seethedisplaychangetothelast-selecteddevice
(e.g.,TV).
continuedonnextpage...
SELECT
29

USING LEARNING
Programming A Learning Key (continued)
4. Pressadevicekeyonce(e.g.,TV)toassignadesired
modeforlearning.
5. Selectanopenlearningkey(e.g.,L1)andpressit
once.Youwillseethedisplaychangeto[LEARNING]
andtheLED(redlight)willturnonfor5seconds.
6. Placeyouroriginalremotecontrol(e.g.,TVremote
control)head-to-head(about2"apart)fromthe
URC-9910remotecontrol.
7. Onyouroriginalremotecontrol,pressandholdthe
key(i.e.,feature)tobelearneduntilyousee[SUC-
CESS]appearontheURC-9910remotecontrol.The
displaywillreturntodevicemodeyouselectedfor
learning(e.g.,TV).
If thekeywasnotlearned,youwill seean[ERROR]
messageinstead.
Repeatsteps5through7asneededtoachieve
[SUCCESS].
8. Tolearnfunctionsontootherlearningkeys(e.g.,L2
~L4),repeatsteps4through7foreachkey.
9. PressEXIT toexittheprogrammingmode.Youwill
seean[EXIT SETUP]messageastheremotecontrol
returnstonormaloperation.
10. Totestalearnedfeature,aimtheURC-9910remote
controlatthedesireddeviceandpressitsdevicekey
once(e.g.,TV,wherethelearningmodewas
assigned).Thenpressthelearningkey(e.g.,L1)
2"
30

wherethelearnedfeatureisstored.Thefeature
shouldactivate.If not,trytheprogrammingthe
learningkeyagain,startingwithstep1(onpage29).
Deleting A Function From A Learning Key
1. OntheURC-9910remotecontrol,pressandhold
SETuntilyouseethedisplaychangefromthecur-
rentdeviceandtimeto[CODE SET].
NOTE:Thedevice,itscode,andtimeareexamples.Your
remotecontrolsettingsmaybedifferent.
NOTE:Toexitprogrammingatanytime,press
EXIT onceor
allow30secondsof inactivityto lapse.Youwillsee
[EXIT
SETUP]
astheremotecontrolreturnstonormaloperation.
NOTE:
[INVALID] meansyouhaveinadvertentlypressedan
incorrectkey.Noteyourerrorandcontinueprogramming.
2. Pressthe▼keythreetimes untilyouseethedisplay
change to [IR DELETE].
(x 3)
NOTE:If yougo past [IR DELETE] ,pressthe ▲ keyoneor
moretimestoreturntoit.
3. PressSELECT oncetobeginprogramming.Youwill
seethedisplaychangetothelast-selecteddevice
(e.g.,TV).
4. Pressadevicekeyonce(e.g.,TV)forthemodethat
containsthelearnedfunction.
5. Presslearningkeyonce(e.g.,L1)wherethefeature
(tobedeleted)isstored.Youwillseethedisplay
change to[DELETED] andthenreturntolast-selected
mode(e.g.,TV).
6. If desired,repeatsteps4 and5 todeleteother
learnedfunctions.
7. PressEXIT toexittheprogrammingmode.Youwill
seean[EXIT SETUP]messageastheURC-9910
remotecontrolreturnstonormaloperation.
SELECT
31

USING VOLUME LOCK
Initsdefault(unlocked)state,theURC-9910remotecontrolallows
eachdevicetocontrolitsownvolumeonlyinitsownmode(e.g.,TV
volume in the TVmode,VCR volumein VCRmode,etc.).However,
usingourVolume Lock feature,youcanlockthevolumecontrolsfor
eachdevicetoallmodes(e.g.,RCVR/AMPvolumeinallmodes).
Moreover,using theVolumeUnlockfeature(seethenextpage),
youcanfurthercustomizethesettingssothatadevice’svolume
controlsareunlockedinonemode,butremainlockedinallother
modes(e.g.,TVvolume in the TV modeandRCVR/AMPvolume in
othermodes).
Programming Volume Lock
1. OntheURC-9910remotecontrol,pressandhold
SETuntilyouseethedisplaychangefromthecur-
rentdeviceandtimeto[CODE SET].
NOTE:Thedevice,itscode,andtimeareexamples.Your
remotecontrolsettingsmaybedifferent.
NOTE:Toexitprogrammingatanytime,press
EXIT onceor
allow30secondsof inactivityto lapse.Youwillsee
[EXIT
SETUP]
astheremotecontrolreturnstonormaloperation.
NOTE:
[INVALID] meansyouhaveinadvertentlypressedan
incorrectkey.Noteyourerrorandcontinueprogramming.
2. Pressthe▼keyfourtimesuntilyouseethedisplay
change to [VOL LOCK].
(x 4)
NOTE:If yougo past [VOL LOCK] ,pressthe ▲ keyoneor
moretimestoreturntoit.
3. PressSELECT oncetobeginprogramming.Youwill
seethedisplaychangeto[TO MODE].
4. Pressamodekey(e.g.,RCVR/AMP)tolockadevice’s
volumecontrolstoallmodes.Youwillseethedisplay
changeto[SUCCESS]andthen[EXIT SETUP] asthe
remotecontrolautomaticallyexitstheprogramming
modeandreturnstonormaloperation.
5. If desired,repeatsteps1 through4 asneeded tolock
volumecontrolsforotherdevicestoallmodes.
SELECT
32

Programming Volume Unlock
1. OntheURC-9910remotecontrol,pressandhold
SETuntilyouseethedisplaychangefromthe
currentdeviceandtimeto[CODE SET].
2. Pressthe▼keyfivetimesuntilyouseethedisplay
change to [VOL UNLOCK].
(x 5)
NOTE:If yougo past [VOL UNLOCK] ,pressthe ▲ keyoneor
moretimestoreturntoit.
3. PressSELECT oncetobeginprogramming.Youwill
seethedisplaychangeto[ALL MODE].
Tounlockonemode,skiptostep4.Otherwisepress
SELECToncetounlockallmodes.Youwillseethe
displaychangeto [UNLOCKED]andthen[EXIT SETUP]
astheremotecontrolautomaticallyexitsthepro-
grammingmodeandreturnstonormaloperation.
4. (Optional)Press▲(or▼)once.Youwillseethe
displaychangeto[ONE MODE].
or
a. PressSELECT once.Youwillsee thedisplaychange
to [SEL MODE].
b. Pressamodekeyonce(e.g.,TV)tounlockit.
Youwillseethedisplaychangeto[UNLOCKED]
andreturnto[SEL MODE].
c. If desired,repeatstep4b asneededtounlock
volumecontrolsforotherdevices.Otherwise,
press EXITtoexittheprogrammingmode.You
willseean[EXIT SETUP]messageastheremote
controlreturnstonormaloperation.
SELECT
33
SELECT