ONV POE33064P User manual

USER GUIDE
Gigabit Ethernet PoE Switch
PoE & Optical Transmission

Statement
Copyright @ 2002-2013 Optical Network Video Technologies (Shenzhen) Co., Ltd
All Rights Reserved
®
!
Packing List
Please kindly check the following items:
1 Gigabit PoE switch
1 Power Adapter
1 Mounting Kits
1 User Guide/Conformity Certificate/Warranty Card
Note
If any shortage or damage found, please contact us in time.
This document contains proprietary information that is protected by copyright. No part of this document may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written
permission of Optical Network Video Technologies (Shenzhen) Co., Ltd.
is the registered trademark of Optical Network Video Technologies (Shenzhen) Co., Ltd. The information
and product specifications within this document are subject to change at any time, without notice and without obli-
gation to notify any person of such change.

Product overview
Product Introduction
10/100/1000M PoE switch can provide both 10/100/1000M Ethernet data and Power over network cable, it
can be used as Ethernet Power Sourcing Equipment, it can automatically detect and identify whether connected
devices such as IP camera comply with standard IEEE PoE 802.3af, 802.3at and supply power for them. 10/100/
1000M PoE switch easier the deployment of Wireless AP, IP camera and IP-based network equipment.
PoE Technology is Power over Ethernet technology, It is refering to transfer both Ethenet data and and DC Power at the same time for IP Phone,
Wilress AP, IP-based camera. These devices which receive DC power is called Powered Device(PD).
Note
The product ‘Switch’ mentioned in the manual, if without a special request, it is refering to 10/100/1000M
PoE switch, PoE switch in short in below.
Feature
Comply to IEEE802.3, IEEE802.3u, IEEE802.3af(POE33604P support 15.4W only), IEEE802.3at.
10/100/1000M self-adaptive, down link port support PoE.
All the ports support Auto MDI/MDIX.
Each PoE port support Power up to 15.4Watts(IEEE802.3af), 30Watts(IEEE802.3at)
Comptible with Powered device applied to IEEE802.3af
Support IEEE802.3x Full Duplex flow control and Duplex backpressure flow control fuction
Automatic MAC address learning and aging.
4K MAC Address
16G Broadband and Kb forwarding memory. 192
High perf rmance full load power configuration.o
LED indicator monitor working status and help fault detection
!

Technical Structure and Port Description
A. PoE Injector Ports B Gigabit . 100-240VAC,50/60Hz
AC 220V 50Hz
A
B
279mm
12345678
44mm
LIN K PoE
12345678
195mm
100 M
1000M
PWR
10 100 1000/ / M PoE Switch
Powe r Ove r Eth ern at Gig abit Po E Switc h
LIN K PoE
SPD LIN K PoE LIN K
1 2 3 4 5 6
10/100/1000M PoE Sw itc h
Pow er Ove r Eth ern at Gig abit Po E Switc h
185mm
36mm
113mm
A.PoE port B.Uplink C. AC 100-240V
AC/IN 100-240V
A
C
SPD LIN K PoE LIN K
1 2 3 4 5 6
B

Indicator description:
Indicator Status Description
Power indicator: P Green LED ON Normal Power Supply
System Indicator: SYS
Please confirm that the PD devices are complying with IEEE802.3af/at standard.
Priority:
switch port will be sorted by priority, port1, port2, port3, port N then power supply of lowest priority will be off.
this function will protect device when it is overload, if all PD consumption are higher than specified,
Power port, Power adapter:
supply; Please input AC110-245V\50Hz for internal power supply switch.
please use 48V power supply, the switch will be damaged if use mismatched power
PoE port:
you can estimate the working status of each port on front panel LED.
The PoE ports include PoE function, it can transmit power and data when connected matching device,
Ethernet Port:
also you can estimate the working status of each port on front panel LED.
Except PoE port, other port are Ethernet RJ45 port, all port support Auto MDIMDIX, plug and play,
Link indicator: Link
!Note
Grey Power OFF
Green LED ON Connected PD Device, working properly
Green LED Blink Short circuit or current overload
OFF No Connected PD or Power OFF
Yellow LED Blink Data transmission properly
Yellow LED ON Connected with 10Mbps, 100Mbps or 1000Mbps PD
OFF No connected PD
Green LED ON Working in 100M rate mode
Green LED OFF Do not work in 100M rate mode
Green LED ON Working in 1000 rate modeM
Green LED OFF Do not work in 1000 rate modeM
Rate indicator: 100M
Rate indicator: 1 00M0
Green LED ON Working in 1000 rate modeM
Green LED OFF
Rate indicator: 1 00M0
POE33064P Working in 10/100 rate modeM

Connection Diagram
Cat.5
Monitor
PoE IP Camera
PoE IPCamera
NVR
PoE Switch
PoE 33008P
ACINPUT
PoE Camera
IP
Cat.5
Video line
IP Camera
PoE Splitter
PD 3101
DC OUT
Cat.5
PD-Powered Device
Power over Ethernet Splitter
OFF:12V
ON:5V
PoE RUN
PoE IN
DC OUT
DC RUN
Ethern t oute
IN
OUT
12345678
100M
1000M
PWR
101001000
/ / M PoE Sw itch
Power Over Ethernat Gigabit PoE Switch
LINK PoE

!
Installation guide
Please install with the supporting devices.
Installation
Please confirm the following things before installation:
1 If the POE port power meet the power requirement of the connecting devices.
2 If the POE standard requirement and power supply match with the power receiving device,
“1/2+、3/6-(-span)/4/5+、7/8-(Mid-span).End
3 If the output power of the supporting power adapter is consistent with the specification in the label of the POE switch.
Please install the POE switch according to the following steps:
1 Put the POE switch on the surface of a large and stable table.
2 Plug the power adapter into the power connector, and then connect the power outlet through the power cord.
3 Connect the network devices to the POE switch port though network cable.
Please do not put heavy products on the POE switch, and please ensure good ventilation environment for the POE
switch.Please cut off the power first before plugging the power adapter.
Power
Connect the power cord, plug it in, turn on the power. When turned on, the switch will automatically initialize, and
at this time the following cases will occur for the LED lights:
1 Except the POE port lights, all the other lights will be off after bright, which means the restoration is successful.
2 Power LED remains lit.
If initialization is inconsistent with the above, please check the power.
Note
!Note

www.onvcom.com
Tel:[phone] Fax:[phone] Email:[e-mail]
Address: Room 1003, Block D , Tairan building , Chegongmiao, Futian district ,Shenzhen ,China
Factory address:No 5, A building, SenYuTai S&T park, Longhua road, BaoAn district,Shenzhen, China
Model Descriptions and Installation
P : 8OE33008P Ports 10/100/1000M Switch, Transmission Distance 100M，1-8 Port support PoE，IEEE 802.3af，15.4W for each
Port, Total Power 120W, Internal PSU
P 33008P 8 Ports 10/100/1000M Switch, Transmission Distance 100M，1-8 Port Support PoE，IEEE 802.3at，30W for OE -at :
each Port, Total Power 220W, Internal PSU
P : 8OE33804P Ports 10/100/1000M Switch, Transmission Distance 100M，1-4 Port support PoE，IEEE 802.3af，15.4W for each
Port, Total Power 60W, Internal PSU
P 3 04P 8 Ports 10/100/1000M Switch, Transmission Distance 100M，1-4 Port Support PoE，IEEE 802.3at，30W for OE3 8 -at :
each Port, Total Power 120W, Internal PSU
Connect to power
Gigabit PoE switch adopts AC 100-240V, 50/60Hz.
1.Please check the power supply specification matches with the required;
2.Connect switch power wire to AC power socket, shown as in the following figure.
After installation, please check:
If there is enough space for heat sink; if the power socket is suitable for switch specification; if the power, switch and rack are
properly grounded and if the connection between switch and other network equipments are normal.
Power Supply Connection Figure Mounting Kits Installation Figure Rack Installation Figure
L Angle Iron
Screw
12345678
100M
1000M
PWR
10/100/1000 M PoE Switch
Power Over Ethernat Gigabit PoE Switch
LINK PoE
P 3 4P Ports 10/100/1000M Switch, Transmission Distance 100M，3-6 Port Support PoE，IEEE 802.3af，15.4W for OE3 06 : 4+2
each Port, Total Power 65W, Internal PSU