ONV PD3401 User manual

USER GUIDE
POE & Optical Transmission
PD series---POE splitter

Statement
Copyright @ 2002-2013 Optical Network Video Technologies (Shenzhen) Co., Ltd
All Rights Reserved
®
!
Packing List
Please kindly check the following items:
Note
If any shortage or damage found, please contact us in time.
This document contains proprietary information that is protected by copyright. No part of this document may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or
by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written
permission of Optical Network Video Technologies (Shenzhen) Co., Ltd.
is the registered trademark of Optical Network Video Technologies (Shenzhen) Co., Ltd. The information
and product specifications within this document are subject to change at any time, without notice and without obli-
gation to notify any person of such change.
1. A PoE splitter
2.One DC power cable
3.A user guide/certification/warranty card

Product introduction
performance characteristic
Product Feature
ONV brand PD3401 series PoE splitter is a new product developed for high power network devices that
the total power is above IEEE802.3AT standard.It must be used with the specialized high power PoE
powered devices and also supply 12V (default) or 24V DC power to the devices without PoE function. PoE
( Power over Ethernet)is a technology, which supply DC power to the terminal equipments at the same
time that transmit data according to the IP. It can largely decrease the use of outlay power line which
reduces the cost and can ensure the stability of your network.
Note: ONV PD3401 series PoE splitter can only be suitable to use in the devices linked by Ethernet cables.
Compatible with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3af, IEEE802.3at standard
Transmit the data and power in one network cable
Default output voltage is DC12V, DC24V optional
Plug and play, no configuration
Data transmit rate: 10/100Mbps、10/100/1000Mbps
Superb circuit isolation protection and improve the ability of anti-thunder, anti-static and anti-interference
Mean time between failure:30000h
Transmission channel surge protection 2KV, executive standard: I EC61000-4-5
Good appearance, small size and space-save.

Mechanical strcuture and Port description
A.12V/24V DC Output
B.DC Output
C.Enthernet Output Port
Status Light D.PoE Input Port
E.PoE Input Status Light
ENTHERNET POE
POE RUN
- +
100.00 mm
80.00 mm
PE
DC
35.00 mm
24V
12V
OUT IN
ABCD
E

Product internal design description
Indicator Status Description
DC indicator light:
DC RUN
Green light ON
PoE indicator light:
PoE RUN Green light OFF
Green light ON
Green light OFF
Note: Please make sure that the PoE power sourcing equipment linked with the PoE splitter compliance
with the I EEE802. 3af/I EEE802. 3at.
DC Indicator: Shows the status of the current working voltage and working state
Output voltage: Please choose the correct output voltage in fear of broking the equipment.
PoE port: The PoE port have the PoE function, ie can transmit the data and power spontaneously if the
devices are linked correctly. And judge the work status by the front panel indicator lights.
Ethernet port: Besides the PoE ports, the other ports are the common self-adjusted RJ45 ports. All
the RJ45 ports support AUTO MDI/MDIX, plug and play.
PoE IN wire: Use the 5 styles unshielded twisted pair to link the power supply devices and PoE injector.
Ethernet OUT wire: Use the 5 styles unshielded twisted pair to link the Ethernet equipments to transmit data.
There is a must to equipe with high power injector or high power PoE switch so that to achieve the high power output
DC OUT: The matched power line links to the power port of the Ethernet equipments to supply the 12V/ 24V DC power.
Activate the PoE function, powered properly
Incorrectly link the PoE power supply device
The power output of the DC port is normal and shows the
current working voltage
No output of DC port

PoE splitter cable installation instruction
Installation guide
Please use the assorted equipments to install
Installation
Make the splitter and the power sourcing equipments/PoE devices combined, then the combination can
supply power to the AP, IP camera, IP telephone and the other network equipments in the situation of lacking
of power line or far away from the power outlets.
Please link the PoE splitter correctly in the following steps:
1) Using the 5 styles UTP to link with the power sourcing equipment's PoE port (like the PoE Switch) and
the the PoE splitter's IN port ;
2) Before connecting to devices, please make sure whether the working voltage status of the PoE splitter
accord with the input devices
3) Using 5 styles UTP to link the Ethernet OUT port of the PoE splitter and Ethernet device, then the two
devices can transmit the data.
4) Using the assorted power line to link DC OUT port of the PoE splitter and the power port of the Ethernet devices.
Attention:
1) The power rate of the Ethernet device linked with the PoE splitter cann't exceed the maximum rate of the PoE splitter.
2) Please make sure to choose the correct output voltage, the unmatched voltage may damage the device.
Confirm before installation:
1. Whether the power rate of PoE port is suitable with the requisition of input device;
2. Whether the PoE criterion and the power supply mode is suitable with the powered device.
3. Whether the output rate of asserted power adapter is suitable with the requisition of switch.

Solution diagram
AC Adapter
PoE Switch
PoE 34001P
UPLINK
DC OUT
NVR
PoE Splitter
PD 3401
Dome Camera
Monitor
Cat.5 Video line
Cat.5
DC RUN
DATA OUT DATA & POE
IN
POE RUN
- PE +
60W super high
power output

Product model and parameter description
Fax：[phone]
Mail：[e-mail]
ADD：Room 1003, Block D, Tairan building, Chegongmiao, Futian district ,Shenzhen,China.
Factory：Floor 5, A building, SenYuTai S&T park, Longhua road, BaoAn district, Shenzhen, China.
Tel：[phone]
www.onvcom.com
PD3401:PoE splitter, PD, IEEE802.3at, 12V/24V, 60W, support 10/100/1000Mbps
PD3401G: Gigabit PoE splitter, PD, IEEE802. 3at ,12V/24V, 60W, support 10/100/1000Mbps
Port description: PoE input: RJ45 port; Ethernet and DC power output: RJ45 port and DC port
Network medium: 100BASE-TX: 3、4、5 classes UTP(≤100 meters); 1000BASE-TX:
5 classes or more UTP (≤100 meters)
Network protocol: I EEE 802. 3i；I EEE 802. 3u；I EEE 802. 3x Fl ow Control；IEEE802.3ab;
IEEE8023af/at DTE Power vi a MDI
The other hardware feature: Constant 12V or 24V output
PoE port: PoE power (Power ≥90W for power supply port)
PoE Standard: The maximum output power for PoE is 60W, can be backward compatible with IEEE802.3af/at
PoE transferring wire core: 4/5+、7/8- pair; 1/2+、3/6- pair( simultaneously support)
Physical format: 80x76x25mm(length x width x height) 0. 15kg
After-sale service: 1 year warranty, lifetime maintenance
Working temperature: 0℃~40℃
Store temperature: -40℃~70℃
Working humidity: 10%~90%RH, no congealment
Store humidity: 5%~90%RH no congealment