OpenEye CM-512 User manual

Outdoor Speed Dome Camera
Installation Manual
Accessories
CA-510G
CA-510W
CA-510C
CA-510P25
CA-510P50
CA-510PML
CA-510PMS
CA-510PA25
CA-510PA50
Camera
CM-512
www.openeye.net

2

31515AB 3
Outdoor High-Speed Dome Camera (CM-512)
Installation Manual
Manual Edition 31515AB – AUGUST 2013
©2013, OPENEYE
All Rights Reserved.
No part of this documentation may be reproduced in any means, electronic or mechanical, for any
purpose, except as expressed in the Software License Agreement. OpenEye shall not be liable for
technical or editorial errors or omissions contained herein. The information in this document is
subject to change without notice.
The information in this publication is provided “as is” without warranty of any kind. The entire risk
arising out of the use of this information remains with recipient. In no event shall OPENEYE be
liable for any direct, consequential, incidental, special, punitive, or other damages whatsoever
(including without limitation, damages for loss of business profits, business interruption or loss of
business information), even if OPENEYE has been advised of the possibility of such damages and
whether in an action or contract or tort, including negligence.
This documentation is copyrighted. All other rights are reserved to OPENEYE. OPENEYE, and
OpenEye, are registered trademarks of OPENEYE in the United States and elsewhere; Windows,
and Windows XP Embedded are registered trademarks of Microsoft Corporation. All other brand
and product names are trademarks or registered trademarks of the respective owners.
OPENEYE
Liberty Lake, WA ●U.S.A.

4
Important Safeguards
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments / Accessories
Do not use attachments or accessories unless recommended by the appliance
manufacturer as they may cause hazards, damage product and void warranty.
4. Installation
Do not place or mount this product in or on an unstable or improperly supported
location. Improperly installed product may fall, causing serious injury to a child or
adult, and damage to the product. Use only with a mounting device
recommended by the manufacturer, or sold with the product. To insure proper
mounting, follow the manufacturer's instructions and use only mounting
accessories recommended by manufacturer.
5. Power source
This product should be operated only from the type of power source indicated on
the marking label.
Precautions
Operating
•Before using, make sure power supply and others are properly connected.
•While operating, if any abnormal condition or malfunction is observed, stop
using the camera immediately and then contact your local dealer.
Handling
•Do not disassemble or tamper with parts inside the camera.
•Do not drop or subject the camera to shock and vibration as this can
damage camera.
•Do not block the cooling holes on the bracket. This camera has a cooling
fan inside the housing. Blocking the cooling holes will cause heat to build up
and cause malfunction.
•Care must be taken when you clean the clear dome cover. Scratches and
dust will ruin the image quality of your camera.Do not use strong or
abrasive detergents when cleaning the camera body. Use a dry cloth to
clean the camera when it is dirty. In case the dirt is hard to remove, use a
mild detergent and wipe the camera gently.

31515AB 5
Installation and Storage
•Do not install the camera in areas of extreme temperatures in excess of the
allowable range. ( -58°F ~ 122°F / -50°C ~ 50°C)
•Avoid installing in humid or dusty places. The relative humidity must be
below 90%.
•Avoid installing in places where radiation is present.
•Avoid installing in places where there are strong magnetic fields and electric
signals.
•Avoid installing in places where the camera would be subject to strong
vibrations.
•Never face the camera toward the sun. Do not aim at bright objects.
Whether the camera is in use or not, never aim it at the sun or other
extremely bright objects. Otherwise the image may be smeared and sensor
may be damaged.
Regulation
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This symbol on the product or on its packaging indicates that this product
shall not be treated as household waste in accordance with Directive
2002/96/EC. Instead it shall be handed over to the applicable collection point
for the recycling of electrical and electronic equipment. By proper waste
handling of this product you ensure that it has no negative consequences for
the environment and human health, which could otherwise be caused if this
product is thrown into the garbage bin. The recycling of materials will help to
conserve natural resources.
For more details information about recycling of this product, please contact
your local city office, your household waste disposal service or the shop
where you purchased the product.
Compliance is evidenced by written declaration from our suppliers, assuring
that any potential trace contamination levels of restricted substances are
below the maximum level set by EU Directive 2002/95/EC, or are exempted
due to their application.

6
Warning
DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE.
DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Caution
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

31515AB 7
Standard Warranty
OpenEye warrants all new products to be free from defects in workmanship and
material under normal use for a period of two years after the date of purchase. Any
defective product that falls under this warranty will, at Openeye’s discretion, be
repaired or replaced at no additional charge. OpenEye may elect to replace defective
products with new or factory-reconditioned products of equal or greater value.
Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
Exceptions to this are listed below.
•Three years on all Digital Recorders
•Three years on all fixed cameras.
All products shall be covered by a one-year advance replacement warranty.*
OpenEye will warrant all otherwise out-of-warranty replacement parts and repairs for
90 days from the date of OpenEye shipment.
The above warranty is the sole warranty made by OpenEye and is in lieu of all other
warranties by OpenEye express and implied, including without limitation the
warranties of merchant ability and fitness for a particular purpose. Under no
circumstances will OpenEye be liable for any consequential, incidental, special, or
exemplary damages arising out of or connected with the sale, delivery, use, or
performance of the product, even if OpenEye is apprised of the likelihood of such
damages occurring. In no event shall OpenEye liability exceed the purchase price of
the product.
This warranty gives you specific legal right and you may also have other rights which
may vary from state to state or country to country.
*Requires corresponding security deposit. Advanced Replacement is limited to
components only outside of the USA and Canada.
For the most up-to-date information, visit www.openeye.net.

8
TABLE OF CONTENTS
Introduction ...................................................................................................................................10
Overview ....................................................................................................................................10
General Operation Requirements...............................................................................................10
System Configuration.............................................................................................................10
Getting Started ..............................................................................................................................12
Box Contents..............................................................................................................................12
Dome Setup and Cable Connection...........................................................................................13
Preparations for Dome Setup.................................................................................................13
Switch Definitions..............................................................................................................15
RS-485 Switch Setting......................................................................................................16
Camera ID Setting.............................................................................................................16
Dome Control Protocol Setting...............................................................................................17
Power Connector..............................................................................................................18
Apply Alarm I/O.................................................................................................................18
RS-485 Connector Definition ............................................................................................19
Grounding Recommendation............................................................................................20
Dome Dimensions......................................................................................................................21
Optional Accessories..................................................................................................................22
Dome Camera Accessories...................................................................................................22
Mounting Accessories............................................................................................................22
Ceiling Mounting with Pole.....................................................................................................23
Wall Mounting with Wall Mount Bracket.................................................................................24
Wall Mounting with Corner Mount..........................................................................................26
Pole Mounting........................................................................................................................27
Specifications................................................................................................................................28
Camera Specifications................................................................................................................28
PTZ Specifications......................................................................................................................29

31515AB 9
NOTES:

10
INTRODUCTION
OVERVIEW
With a weather resistant design, the Integrated High Speed Dome Camera is
applicable for outdoor installations. The dome camera supports all-in-one cabling for
easy installation and can be integrated with CCTV products such as reocrders,
control keyboards, and CCTV accessories for a total surveillance solution. In
addition, a large set of built-in protocols provides connectivity to other surveillance
systems. The built-in protocols include OPTIX 3, Pelco, VCL, Philips, AD-422, and
many others.
GENERAL OPERATION REQUIREMENTS
A minimum of one control device is required for operation, such as a control
keyboard, or a recorder. The CM-512 includes a built-in receiver that decodes
commands from a control device.
Connect dome cameras to other devices, as shown in the diagram below, to
complete a video surveillance system.
System Configuration
Note To extend the network distance up to 1.2 km (4000 feet) and to protect the connected
devices, OpenEye recommends placing a repeater at the mid-point. However, a repeater
may be needed with network distances less than 1.2 km if the cables used are not CAT 5,
24-gauge cables. Refer to the repeater’s manual for detailed information.

31515AB 11
NOTES:

12
GETTING STARTED
BOX CONTENTS
Before proceeding, please check that the box contains the items listed here. If any item
is missing or has defects, DO NOT install or operate the product. Contact your dealer for
assistance.
CM-512 Camera Optical Cover Screws (x4)
Quick Start Guide User Manual Waterproof Gasket
Installation Manual Lubricant

31515AB 13
DOME SETUP AND CABLE CONNECTION
Before installing or connecting the dome camera, please refer to this section and
complete preparations for dome setup and all switch settings.
Preparations for Dome Setup
The following installation procedure is for the outdoor dome equipped with the sunshield housing.
Please follow the steps below to complete dome housing installation.
1. Unpack the dome package and take out the dome body.
2. Remove the protective cover and PE sheet.
3. Attach the dome cover to the camera body. Before doing that, apply some
lubricant to the waterproof gasket. This helps keep moisture out of the dome.
Note The protrusion on the cover must alight with one of the four holes on the camera body.

14
4. Using both hands, gently press the dome cover. Do not press the cover from
the dome.
5. Use screws to affix the dome cover to the body.
6. Set the switches located on the bottom of the camera. Refer to the user manual
for information about various switch settings.

31515AB 15
Dome Camera Setup
Before connecting the dome camera to other CCTV devices, please complete the
camera ID and communication switch settings. These switches are located on the
bottom of the dome camera.
Switch Definitions
Alarm inputs
Communication switch
Protocol switch
Camera ID switch
ISP connector
(
reserved)
BNC output
Power
RS485 connector

16
RS-485 Switch Setting
Switch SW1 RS-485 Setting
SW2
SW3 Termination
SW4 Line Lock
SW5 System Initialization
SW6 Reserved
RS-485 is the interface that the dome
camera uses to communicate with its
control device; for this reason, the RS-
485 setup of the dome and the control
device must be the same. The RS-485
default setting is half-duplex (see the
diagram right). Do not change the
default setting without a qualified
specialist or supplier’s notice.
Camera ID Setting
Assign an ID number to your camera if there is more than one camera in the
network. The camera ID is set up using the camera ID switch on the back plate of
the camera.
For switch configuration details, please refer to Appendix B in the User Manual.
Note No two cameras should have the same ID, or communication conflict may occur.
RS-485 Setting
Half-duplex Full -duplex

31515AB 17
Dome Control Protocol Setting
Define the protocol you are going to use based on the devices of your surveillance
system. Generally, use one protocol even if the devices are provided by different
manufacturers. Use the switch to set your dome control protocol and the baud rate.
Refer to the table below and turn the arrow to choose a protocol for your speed
dome.
Protocol Baud Rate
Setting
Switch Setting
1 2 3 4 5 6
VCL 9600 OFF OFF OFF OFF OFF OFF
Pelco D 2400 ON OFF OFF OFF OFF OFF
Pelco P 4800 OFF ON OFF OFF OFF OFF
Chiper 9600 OFF OFF ON OFF OFF OFF
Philips 9600 ON OFF ON OFF OFF OFF
OPTIX 3 9600 ON ON ON OFF OFF OFF
AD422 4800 OFF OFF OFF ON OFF OFF
DP P 9600 ON OFF OFF ON OFF OFF
Pelco D 4800 ON ON OFF ON OFF OFF
Pelco D 9600 OFF OFF ON ON OFF OFF
Pelco P 2400 ON OFF ON ON OFF OFF
Pelco P 9600 OFF ON ON ON OFF OFF
JVC 9600 ON ON ON ON OFF OFF
Kalatel-485 9600 ON OFF ON OFF ON OFF
Kalatel-422 4800 OFF ON ON OFF ON OFF
Example To set the protocol Pelco D at a 2400 baud rate, the
protocol switch should be set as shown..

18
Power Connector
Refer to this diagram for power connector definition before wiring.
1 AC IN +
2 Frame GND
3 AC IN -
Apply Alarm I/O
The CM-512 supports 4 digital alarm inputs and 2 digital alarm outputs. Please
make sure the alarm connections are properly wired before starting to configure
alarm-related settings. Please refer to the pin definition table for alarm system
wiring.
Pin Definition Pin Definition
1 Alarm Out NO 1 7 Alarm Out COM 2
2 Alarm Out NC 1 8 GND
3 Alarm Out COM 1 9 Alarm In 4
4 GND 10 Alarm In 3
5 Alarm Out NO 2 11 Alarm In 2
6 Alarm Out CN 2 12 Alarm In 2

31515AB 19
RS-485 Connector Definition
The dome camera uses the RS-485 interface to communicate with a connected
control device. Connect a control keyboard to the speed dome using the terminal
block. OpenEye recommends using CAT 5 cables for RS-485 communication with
a maximum length of 4000 feet (1219 meters) for 24-gauge wire. If the total cable
length exceeds 4000 feet, use a repeater to maintain the signals. Refer to the table
below for pin definition and wiring.
Connector Pin Number Definition
1 R-
2 GND
3 R+
4 T-
5 T+

20
Grounding Recommendation
The GND wire must be directly connected to the middle pin of the AC24V power
connector. Failure to connect the ground can cause damage and failure of the
camera and may void the warranty.
If the connection of the GND wire causes video noise, use a video isolator. This is
only necessary in some situations.
AC 24V
VIDEO OUT
Mustbe
connected
to ground
(GND)
Video
Isolator
Optional
AC 24V
Adapter
3 pinsterminal block
VIDEO OUT
RS-485
Alarm I/O
2
3
4