OpenEye OE-C3011D4 User manual

4MP Indoor IP Dome
OE-C3011D4
37552AC
QUICK START GUIDE
This quick start guide provides
only basic information on the
camera’s settings and operation for
initial installation. Please read the
user manual for optimal camera
confi gurations.
Scan the QR code or go to
openeye.net/downloads
Find the latest product
documentation and software.
Copyright ©2021 OpenEye.
All Rights Reserved. Information contained in this
document is subject to change without prior notice.
OpenEye does its best to provide accurate information but
cannot be held responsible for typos or mistakes.
Liberty Lake, WA, USA
509.232.5261
openeye.net
CONNECTIONS
1
2
1
1
RJ-45
RJ-45
-
-
For network and PoE connections
For network and PoE connections
2
2
Power (12vDC)
Power (12vDC)
1
1
12vDC +
12vDC +
Power Connection
Power Connection
2
2
GND -
GND -
3
3
Reset Button
Reset Button
-
-
To restore the camera to factory defaults:
To restore the camera to factory defaults:
1. Disconnect power for 30 seconds.
1. Disconnect power for 30 seconds.
2. Reconnect power and wait 30 seconds.
2. Reconnect power and wait 30 seconds.
3. Press and hold the reset button for 20 seconds.
3. Press and hold the reset button for 20 seconds.
4
4
Alarm & Audio I / O
Alarm & Audio I / O
1
1
Alarm Out -
Alarm Out -
Alarm connection
Alarm connection
2
2
Alarm Out +
Alarm Out +
3
3
GND
GND
Ground connection
Ground connection
4
4
Alarm In
Alarm In
Alarm connection
Alarm connection
5
5
GND
GND
Ground connection
Ground connection
6
6
Audio In
Audio In
Two-way audio transmission
Two-way audio transmission
7
7
GND
GND
Ground Connection
Ground Connection
8
8
Audio Out
Audio Out
Two-way audio transmission
Two-way audio transmission
5
5
microSD Card Slot
microSD Card Slot
-
-
Supports up to 512GB microSD card for Edge storage.
Supports up to 512GB microSD card for Edge storage.
Do not add or remove the microSD card when the camera is powered on.
Do not add or remove the microSD card when the camera is powered on.
5
4
3

CONTENTS
Selecting multiple cameras and enter-
ing IP address 192.168.51.2 will set
an IP address on all selected cameras,
starting at 192.168.51.2 and increase
per camera.
1. Open the Network Camera
Manager application.
2. Select applicable camera(s).
3. Input starting IP address, Subnet
Mask, Gateway, DNS.
4. Apply changes.
5. Wait 60 seconds before refreshing
NCM.
OE-3011D4
Mini Dome Camera
CABLING INSTRUCTIONS
Self-Tapping
Screws &
Plastic Anchors
2-Pin Terminal
Power Block
Quick Start
Guide
Mounting Template
ASSIGNING AN
IP ADDRESS
OpenEye IP cameras are set to DHCP
by default. If a DHCP server is not
detected after 4 minutes, the camera
will default to IP address 192.168.51.2.
If you are not using a DHCP server,
NCM will allow you to batch confi gure
a static IP address.
The IP address for the camera network
on your Apex recorder is 192.168.51.1.
NOTE: To change this IP address please refer
to your Apex recorder manual.
CONNECTING TO THE
IP CAMERA
To access the camera setup menu,
you need to open Network Camera
Manager (NCM) utility. NCM is pre-
installed on all OpenEye Recorders,
and is also available for download on
the OpenEye website for installation on
your personal computer or laptop.
1. Open Network Camera Manager.
2. Locate your camera on the
Network Camera Manager list.
3. To open the web browser, select
the camera and click LOAD.
NOTE: OpenEye IP cameras ship
without a default password.
DEFAULT USERNAME
AND PASSWORD
The admin user password can be set
using the following methods:
1. OpenEye recorders running Apex
2.1 or newer will automatically set
a new unique password if:
• Connected to an M-Series
recorder with a built in PoE
switch.
• Connected to a network
switch through the
camera network port
and selected then added in
setup, if a new password has
not already been set.
NOTE: The NCM software manual can be
found at https://www.openeye.net/
ncm-manual
Tapered RJ45 Sleeve
Security Torx Tool #2 Phillips Bit
2x - 21mm Cable
Grommet
2x - 28mm Cable
Grommet
Optional Free Paintable Dome Cover
This camera has an available paintable dome
cover allowing it to be quickly converted to a
black housing or the allow custom painting to
match its installation environment. To reduce
waste it is not included in every package but
may be requested free of charge at time of
purchase.
1. Push the RJ45 connector into the
tapered sleeve.
2. Cut the end off the center of
the cable grommet and feed
the network cable through the
opening.
3. Remove the tapered sleeve.
4. Insert the RJ45 connector into
the network port. Pull the cable
downward to make sure the
cable grommet protrudes to the
direction opposite to the RJ45
connector.
2. Connect to the camera directly
through a Web Browser and follow
the onscreen prompts.
3. Use the Network Camera Manager
(NCM) Utility.
Username: admin
Set the Default Camera Password
Use the QR code or link for instructions on
defi ning a unique camera password:
https://www.openeye.net/support/faqs/
default-camera-password