Optos G112883002 User manual

Optos Arm Rest
Installation and User Guide G112883002
Technical specifications
Note: The arm rest height does not include the height from the floor to the table
base where the arm rest connects.
Parts supplied
A 6 mm hex key is required to assemble the arm rest.
Warnings and cautions
The Optos arm rest MUST be operated within the safety parameters and instructions defined in the Optos Table User Guide.
If you have any questions regarding the correct use of the Optos arm rest, please contact your Optos representative before
attempting to operate the Optos arm rest.
WARNING
Do NOT lean on the arm rest.
Ensure the patient or operator’s arm is NOT trapped or impacted when the arm
rest position is adjusted or when Optos table height is adjusted.
Incorrect positioning of the arm rest MAY result in patient harm.
CAUTION
If you suspect the arm rest is faulty, please contact your Optos representative.
In order to prevent any contamination always clean and disinfect parts of the
equipment which will be in contact with the patient.
Be careful NOT to damage the arm rest when cleaning.
Dimensions
Details
Width
12 cm (5 inches)
Depth
35 cm (14 inches)
Arm rest height
55 cm to 75 cm (22 inches to 30 inches)
Arm rest weight
1.7 kg (3.8 lbs)
Maximum load on Arm rest
15 kg (33 lbs)
#No
Part
Description
1
Arm rest
Supports the patient arm
2
Screw
Prevents loosening
3
Spring washer
Prevents loosening
4.
Plain washer
Connects the arm rest to the Optos Table

Optos Arm Rest
Installation and User Guide G112883002
Part Number: G112883002 Page 2 of 3
Copyright 2020, Optos plc. All rights reserved. English
Cleaning before each patient
The following cleaning procedures should be carried out before each session. External surfaces must be cleaned of all visible
contamination when they become dirty or soiled with bodily fluids. Follow your internal clinic or hospital decontamination
procedures.
1. Clean the arm rest surfaces with an individually sealed, 70% IPA (isopropyl alcohol) wipe.
2. Allow the cleaned areas to air-dry before imaging the next patient.
Attaching to the table
1. Remove the plug from the table leg that you wish to mount the arm rest to. Retain the plug for future use.
2. Screw a screw (5) with washers (3, 4) onto Optos Table (2)
3. Position the arm rest assembly (1) onto the thread and tighten the screw with a hex key.
Moving the arm rest to the other leg
1. Remove the plug from the table leg that you wish to move the arm rest to. Retain the rubber plug.
2. Loosen the arm rest assembly (1) and screw (5) and remove from the table leg.
3. Follow step 3 of the Attach to the table procedure to attach the arm rest onto new table leg.
4. Fit the retained plug in the hole in the unused table leg.
Adjusting the height
1. Loosen the height adjustment handle (1).
2. Move the arm rest to the preferred height and tighten the arm rest height adjustment handle.
No
Part
1
Arm rest
2
Optos Table
3
Plain washer
4
Spring washer
5
Screw

Optos Arm Rest
Installation and User Guide G112883002
Part Number: G112883002 Page 3 of 3
Copyright 2020, Optos plc. All rights reserved. English
Adjusting the angle
1. Loosen the pivot adjustment handle (1).
2. Move the arm rest to preferred inclination and tighten the pivot adjustment handle.
3. Ensure the handle locks in place, pointing upwards.
Positioning patients
1. Position the arm rest so the pad (1) is parallel with the edge of the table (2) and does
not create a clash hazard.
2. Position the patient’s arm so that it lies along the length of the arm rest pad.
Contact us
Visit optos.com to find your local contact details.
Copyright 2020, Optos plc. All rights reserved.
Optos plc. products are protected by patents and patent applications listed at optos.com/patents.
The information contained within this document is subject to change without notice. The latest version of this information can be found at optos.com.
Print Date: 14 September 2020
Optos Inc
Tel: [phone]
[email protected]
Optos plc
Tel: [phone]
[email protected]
Optos Australia
Tel: [phone]
[email protected]