Orbital Systems Oas Indo User manual

Oas Indo Manual
Oas Indo EU INSTALLATION 190923 INSTALLATION

2
(46)
EU D ECLARATION OF C ONFORMITY (D O C)
We Orbital Systems AB,
Hans Michelsensgatan 10A
211 20 Malmö
Sweden
Hereby declare that this DoC is issued under our sole responsibility and belongs to the following product:
OS8732-Ei2
This declaration is in conformity with the relevant union harmonized legislations:
RED 2014/53/EU RoHS 2015/863 LVD 2014/30/EU
The following harmonized standards and technical specifications have been applied:
EN 300 328 v2.1.1 EN 301 489-1 v2.1.1 EN 301 489-17 v3.1.1
EN 300 330 v2.1.1 EN 62311:2008 EN 60335-2-105:2005+A1+A11
Additional standard that has been applied to the product:
UL 1951 IGC-330-18 FCC Part 15 B
EN 1717 BBR NSF55
EN 13076
The product has undergone mandatory or voluntary certification procedures in order to receive the following certifications:
KIWA TG 1503 KIWA K100686/01 IAPMO E10059
IAPMO C-11154 IAPMO W-11301
Signed for and on behalf of Orbital Systems AB
Place Date Name Position
Malmö 2019-08-28 Mehrdad Mahdjoubi CEO
Introduction & Safety Messages
This manual applies to model OS8732 Ei2.
Thank you for purchasing the Oas shower system. To enjoy the
full potential of the shower please read and follow the procedures
in this manual. Make sure that you fully understand how to
operate this shower and make sure that it is properly maintained
in accordance with the instructions given in this manual. Do
not throw this manual away, keep it handy for future reference.
EU DECLARATION OF CONFORMITY
This system is certified by IAPMO
R&T to NSF 55, Class B
The manufacture of this product has been made in accordance with the Construction Products
Certificate decision on production control and the documents submitted to the decision of issue
of this certificate.

4
(46)
WARRANTY
Introduction & Safety Messages
The Oas shower and its components are manufactured from high-quality
materials and assembled under strict standards.
Orbital Systems warranty covers defects which appear within a period of
two years from delivery of the product.
Orbital Systems warranty does not cover:
• Defects arising out of materials or a design specified by the Customer,
or by any alterations carried out without our consent.
• Defects that appear under conditions of operation not provided for
and under improper use of the product.
• Defects caused by faulty maintenance, incorrect installation or a faulty
repair.
Repairs should be carried out only by Orbital Systems, one of our
certified service partners or the customer only when certified.
For showers outside of the warranty period spare parts are available for
purchase directly from Orbital Systems or through one of our certified
partners.
SAFETY INSTRUCTIONS
The appliance shall be supplied by a switch that provide a full
disconnection under overvoltage category III incorporated in the fixed
wiring plant.
The appliance is designed for a fixed connection to the water mains. Do
not use a detachable water pipe or hose.
Unauthorized modification of internal components and wiring is
prohibited.
If the supply cable is damaged it must be replaced only by the service
assistance or person with similar qualification.

5
(46)
TABLE OF CONTENTS
Installation Overview 6
Installing the Shower Unit 11
Installing the Shower Head 30
Installing the Hand Head Diverter 34
Installing the Hand Shower Holder 38
Installing the Hand Shower 41
Connect OAS to Internet 44
Contact us
[e-mail]
www.orbital-systems.com
Europe CET: [phone]
Orbital Systems and our team of expert staincluding our certified
Service Partners are available to assist you should you require product
advice, experience any problems, need to purchase spare parts or to
set up a service visit.
We recommend your first point of contact should be your installer, who
will be able to oer all of the above services.
Alternatively you can also contact Orbital Systems who will be able
to assist you. Repairs should always be carried out only by Orbital
Systems or a certified partner.
SERVICE

6
(46)
INSTALLATION OVERVIEW

7
(46)(147)
7
1000 mm
Installation Overview
PRODUCT MEASUREMENTS
2190 mm
575 mm
184 mm 122 mm
145 mm
Ø 75 mm
932 mm
600 mm
145 mm
1266 mm
812 mm
440 mm

8
(46)
PREREQUISITES FOR INSTALLATION
Installation Overview
Electrical supply
EU-one phase: AC 220-240 V / 50 Hz / 16 A
Residual circuit breaker: One per shower required. Having a rated residual tripping current not exceeding 30 mA
Mains supply fixed cord: Min. 2.5 mm2(rated for 16 A circuit)
Connectivity
Internet connection: WiFi 2.4 GHz required
Circuit breaker: One per shower required
Plumbing / Water
Hot and Cold Water Inlet: Separate hot/cold inlet required - 1/2” BSPP (G) pipe connection needed
Temperature of inlet water: Cold: +4°C to +30°C
Hot: +40°C to +65°C
Water inlet flow: Min. 9 litres/minute hot and cold
Water pressure: Min. 3 bars/43,5 psi/0,3 MPa measured at the highest point of installation
Max pressure 10 bars / 145 psi / 1 MPa
Hardness of Water: Required: 3°dH-10°dH and Preferred: 6°dH-10°dH or a total hardness of 110-180 mg CaCO3/litres

9
(46)
Drain unit dimensions:
HxWxD: 192 x 812 x 184 mm
Connection to drain:
Ø75 mm
Cold and hot water supply
Recommended Min: 9 litres/minute
Recommended Min: 3 bar,
maximum 10 bar
Electrical supply, power:
230 V/16 A
INSTALLATION OVERVIEW
Installation Overview
Core Wall Enclosure:
HxWxD: 932 x 538 x 145 mm
Min. 2%
600 mm
575 mm
2190 mm

10
(46)
+15-25%
+10-20%
+5-10%
Installation Overview
RECYCLING OPTIMISATION SITE SUGGESTIONS
Based on 8 minutes shower (7 minutes recycling)
in shower space with underfloor heating.
Fully enclosed shower space
Recommended installation by Orbital
Systems

11
(46)
INSTALLING THE SHOWER UNIT
watch video: https://bit.ly/2QNFVLP

12
(46)
COMPONENT OVERVIEW
Installing the Shower Unit
1
2
14
15
16
17
3
18
13
4
5
6
12
7
8
9
10
11
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Hose Connection
Indo Core
Indo Panel
Panel Lock + Magnetic Key
Funnel
Smart Sensor Unit
Sensor Tank
Sensor Cable
Recirculation Hose
Flush Hose
Smart Sensor Lock
+ half thread M4 (3 Hex), x1
+ full thread M4 (3 Hex), x1
WiFi Cable and Antenna
Air Gap Tank
Quartz Glass
UV Lamp
Filter Capsule
Cleaning tablet
Control Dial
Installing the Shower Unit

13
(46)
Installing the Shower Unit

14
(46)
Install Sensor Cable, Flush Hose and, Recirculation Hose.
Make sure the sensor cable goes first.
Installing the Shower Unit
Remove Panel Template and nuts.

15
(46)
Pull the Sensor cable out to where the contact almost
reaches the end of the sensor tank.
Apply lubricant
Connect hoses to the Sensor Lock.
Installing the Shower Unit

16
(46)
Installing the Shower Unit
x1
Half thread
M4 (3 Hex)
CAUTION. If Sensor Lock is misaligned it can cause issues in
further installation steps.

17
(46)
CAUTION. Do not overtighten. Tighten screw until it just
reaches the bottom of the drain bowl.
Insert sensor lock unit into drain
pipe. Twist the Sensor Lock Unit
slightly, and insert it all the way
into the pipe.
Rotate until parallel with drain bowl
bottom.
Insert Smart Sensor Unit Cable through hole in Sensor Tank and
connect with Sensor Cable.
Installing the Shower Unit
x1
Full thread M4 (3 Hex)
CAUTION. Hand tighten cable
connectors to avoid damage.
CAUTION. Make sure the Smart
Sensor Unit is inserted horisontally.
Do not angle the Smart Sensor.
CAUTION. Make sure to have
correct alignment between key
and slot in connectors.

18
(46)
Installing the Shower Unit
CAUTION. Place cable towards
the wall of the drain to avoid
damage.
CAUTION. Make sure Smart Sensor Unit is inserted correctly.
The O-ring should not be visible.
Insert Sensor Tank and connect Smart Sensor Unit with Sensor
Lock. Make sure Sensor Lock is in Open position.
Set Sensor Lock to Locked position.

19
(46)
Remove transport plugs before installation.
Installing the Shower Unit

20
(46)
Installing the Shower Unit
CAUTION. Make sure that hoses and cables are not
pinched.
Insert Core into Core Wall Enclosure and attach safety wire. Keep
tilted to enable electrical installation.
WARNING. Electrical installation should be performed according
to local regulations by a licensed electrician.

21
(46)
x1
M8 Socket Head
Installing the Shower Unit
CAUTION. Make sure to have correct alignment between
key and slot in connectors.