Oregon Scientific FSP-301 User manual

1
EN
TABLE OF CONTENTS
About this guide ................................................... 2
Product overview.................................................. 3
Getting started ..................................................... 8
Batteries........................................................... 8
AC power adapter ............................................ 8
Change settings ............................................... 9
Remote unit set up ............................................... 9
Clock ...................................................................10
Alarm...................................................................12
Weather forecast .................................................13
Temperature ........................................................14
Backlight..............................................................16
Projector..............................................................16
Reset system ......................................................18
Safety and care ...................................................18
Warnings .............................................................18
Troubleshooting ...................................................19
Specifications ......................................................21
Additional resources ...........................................22

2
EN
ABOUT THIS GUIDE
Congratulations on your selection of the Oregon
Scientific Maranello Radio-Controlled Projection
Clock with Indoor and Outdoor Temperature
(FSP-301). This powerful device bundles time
keeping, alarm, projection, indoor and wireless
outdoor temperature measurement features.
Keepthismanualhandyasyouuseyournewproduct.
Itcontainspracticalstep-by-stepinstructions, as well
as technical specifications and warnings you should
know.
In this box, you will find:
· Main unit
· Remote unit
· Batteries
· AC/DC power adapter

3
EN
PRODUCT OVERVIEW
TOPVIEW
1 2 3 4
DESCRIPTIONS
1. Snooze / Light (13, 16)
2. Channel (9, 14)
3. Memory (14)
4. Projection lens (17)

4
EN
LCD DISPLAY
1
6
7
8
2
3
4
5
DESCRIPTIONS
1. Low Battery icon(8)
2. Weather Forecast (13)
3. RF Reception Signal (10)
4. Clock (10)
5. Date / Alarm / Alarm Type (10-12)
6. Remote Sensor (9, 14)
7. Temperature Trend (16)
8. Temperature (14)

5
EN
FRONT VIEW
1 2 3 4
BUTTON DESCRIPTIONS
1. Clock – set time / date or view seconds / day of
week (9, 11)
2. Up / Down – increase / decrease setting
or activate / deactivate auto-synchronization
(9, 11)
3. Alarm – set / activate / deactivate alarm(12)
4. Projector (16)

6
EN
BACKVIEW
4
1
5 6 7
2
3
DESCRIPTIONS
1. Projector focus knob (17)
2. 180˚ rotation (flip image) button (17)
3. Image rotation button (17)
4. ˚C/ ˚F switch (9, 15)
5. Projector switch (17)
6. Radio signal format switch (10)
7. Reset button (18)
NOTE
AC power adapter and battery
compartment not shown.

7
EN
REMOTE UNIT
1
2
6
8
7
4
5
3
DESCRIPTIONS
1. Temperature (14)
2. LED indicator (10, 15)
3. Channel number (9, 14)
4. ˚C/˚F switch (9, 15)
5. Reset button (18)
6. Channel switch (9, 14)
7. Batteries (8)
8. Battery compartment (8)

8
EN
GETTING STARTED
BATTERIES
Batteries for the remote and main units are supplied
with this product. Replace them whenever the low
battery signal ( ) displays. The battery door is
located on the bottom of the main unit. Use a small
Phillips screwdriver to remove the remote unit
compartment lid. Be sure to match the correct
polarity, as shown in the battery compartment. After
you change the batteries, press the RESET button
with the point of a blunt object (such as a ball point
pen).
NOTE
Insert the batteries in the remote unit before
you set up the main unit. Do not use rechargeable
batteries.
AC POWERADAPTER
An AC power adapter is supplied for use with this
product. You must connect the power adapter if you
wish to use the continuous projection feature. The
jack is located next to the battery compartment.
NOTE
IftheAC power becomes unavailable, theunit
will automatically switch to battery power.

9
EN
CHANGE SETTINGS
Press and hold CLOCK or ALARM for 2 seconds to
enter setting mode. Then, press UP or DOWN
tochangeeachsetting. Pressandholdtoenterfast-
setting mode. Press CLOCK or ALARM to switch
between settings.
REMOTE UNIT SET UP
Up to 3 remote units can be used with this product to
monitoroutdoor temperature. The measurementunit
(˚C or ˚F) and channel number (1, 2, or 3) switches
are located in the battery compartment, and should
be set prior to installation.
NOTE
Additionalremote units sold separately. If you
areusing morethanoneremoteunit, besureto select
a different channel number for each unit.
INSTALLATION
Mount the remote unit on a flat surface using the
recess hole on the back of the unit.
For best results:
· Before you insert the batteries, select the
measurement unit and channel number first.
· Placetheunit out of direct sunlightandmoisture.

10
EN
· Do not place the remote unit more than 20 – 30
meters(60–90feet)fromthe main (indoor) unit.
· Positiontheunit so that it faces themain(indoor)
unit. Minimizeobstructions such as doors, walls,
and furniture.
You may need to experiment with various locations
to get the best reception.
CLOCK
This product can automatically synchronize the date
and time with official time-keeping organizations in
Frankfurt(Germany) andRugby(England). Whenthe
unit is within 1500 km (932 miles) of a RF signal, the
reception icon will blink during reception.
SET RADIO SIGNAL FORMAT
The RADIO SIGNAL FORMAT switch is located on
the back of the product. Select EU (DCF) or UK
(MSF). Then, press RESET to reset the unit.
Reception takes 2 – 10 minutes to complete. Once
complete, the icon will stop blinking.