Oregon Scientific RMR183 User manual

Long-Range Multi-Channel In-Out Thermometer
with Cable Free Sensor and RF Clock
Model: RMR1 3 & RMR1 3U
User Manual
RMR183-e Cover R2 OP 8/21/04, 6:22 PM1
Black

1
GB
MAIN FEATURES: MAIN UNIT
Long-Range Multi-Channel
In-Out Thermometer
with Cable Free Sensor and RF Clock
MODEL: RMR183/RMR183U
USER'S MANUAL
INTRODUCTION
Congratulations on your purchase of the RMR183/RMR183U
Long-Range (60 meters) Multi-Channel In-Out Thermometer with
433MHz cable free sensor and radio-controlled calendar clock.
Thebasicpackagecomeswithamainunit,whichisthetemperature
and calendar clock station, and a remote unit, the thermo sensor.
The main unit has a large display for indoor temperature,
calendar clock and temperatures collected and transmitted by the
remote unit. The main unit can support up to three remote units.
The main unit is capable of keeping track of the maximum and
minimum temperature of different sites. No wire installation is
required as the RMR183/RMR183U operates at 433MHz.
As for the calendar clock, it is radio-controlled. It automatically
synchronizes its current time and date when it is brought within an
approximate 1500km radius of the radio signal generated from
Frankfurt, Germany (DCF77) (or Radio signal MSF-60 from
Rugby, England for UK version).
You can also set the calendar clock manually when it is off range.
Otherfeaturesincludefive-languagedisplay,crescendodaily alarm
and interchangeable display modes.
RMR183-e R2 OP 8/21/04, 6:22 PM1
Black

GB
2
A FOUR - LINE LCD DISPLAY
Facilitates easy reading of remote and indoor temperatures and
calendar clock
B[ ] RADIO - RECEPTION SIGNAL
Indicates the condition of radio reception
C TEMPERATURE TREND INDICATOR
Indicates the trend of temperature changes
D [ ] BATTERY - LOW INDICATOR
(REMOTE SENSOR)
Activates when the remote-sensor battery is low
E [ ] BATTERY - LOW INDICATOR
Activates when the battery of main unit is low
F[ ] ALARM - ON ICON
Appears when the alarm is activated
G[(
(
.
)) ] ALARM ICON
Appears when the alarm time is displayed
H [ MODE ] BUTTON
Toggles the calendar clock display modes or activates the
calendar clock setting mode
I [ALARM] BUTTON
Displays the alarm time or sets the alarm status
J [MEMORY] BUTTON
Displays maximum / minimum temperature
K [CHANNEL] BUTTON
Selects remote-sensor channels
L[ ] BUTTON
Advances the value of a setting
M[ ] BUTTON
Decreases the value of a setting
N [RESET] BUTTON
Returns all settings to default values
O°C/°F SLIDE SWITCH
Selects between degree Centigrade (°C) and Fahrenheit (°F)
P BATTERY COMPARTMENT
Accommodates two (2) UM-3 or “AA” size 1.5V batteries
Q REMOVABLE TABLE STAND
For standing the main unit on a flat surface
R WALL-MOUNT HOLE
For mounting the main unit on a wall
RMR183-e R2 OP 8/21/04, 6:22 PM2
Black

3
GB
MAIN FEATURES: REMOTE UNIT THN128 A LED INDICATOR
Flashes when the remote sensor transmits a reading
B CHANNEL SLIDE SWITCH
Designates the remote sensor Channel
C RESET BUTTON
Returns all settings to default values
D BATTERY COMPARTMENT
Accommodates two (2) UM-4 “AAA” size 1.5V batteries
E BATTERY DOOR
F WALL-MOUNT HOLDER
Supports the remote unit in wall-mounting
G REMOVABLE TABLE STAND
For standing the remote unit on a flat surface
BEFORE YOU BEGIN
For best operation,
1. Assign different channels to different remote units.
2. Insert batteries for remote units before doing so for the main
unit.
3. Place the main unit as close as possible next to the remote unit
and reset the main unit after installing batteries. This will
ensure easier synchronization between the transmission and
reception of signals.
4. Position the remote unit and main unit within effective trans-
mission range, which is 60 meters in open area.
RMR183-e R2 OP 8/21/04, 6:22 PM3
Black

GB
4
Note:
1. Replace batteries when the low-battery indicator of a
particular channel activates on the main unit.
2. Once a channel is assigned to a remote unit, it can only be
changed by removing the batteries or resetting the unit.
BATTERY INSTALLATION: MAIN UNIT
1. Open the battery compartment door.
2. Install 2 batteries (UM-3 or “AA” size 1.5V) strictly according
to the polarities shown.
3. Replace the battery compartment door.
LOW BATTERY WARNING
When it is time to replace batteries, the low-battery indicator will
show up when the corresponding channel is selected. The battery
level of the main unit will be shown on the indoor temperature
when it is running low.
Note that the effective range is vastly affected by the building
materials and where the main and remote units are positioned. Try
various set-ups for best result.
Though the remote units are weather proof, they should be placed
away from direct sunlight, rain or snow.
BATTERY INSTALLATION AND
CHANNEL SETTING: REMOTE UNIT
The remote unit uses two (2) UM-4 or “AAA” size 1.5V batteries.
Installation:
1. Remove the screws on the battery compartment.
2. Select the channel on the CHANNEL slide switch.
3. Insert the batteries strictly according to the polarities shown.
4. Replace the battery compartment door and screws.
RMR183-e R2 OP 8/21/04, 6:22 PM4
Black

5
GB
THE RESET BUTTON
This button is only used when the unit is operating in an unfavor-
able way or malfunctioning. Use a blunt stylus to hold down the
button. All settings will return to their default values.
GETTING STARTED
Once batteries are in place for the remote units, they will start
transmitting temperature readings at 30 second intervals.
The main unit will also start searching for signals for about a
minute once batteries are installed. Upon successful reception,
the individual channel temperatures will be displayed on the top
line and the indoor temperature on the second line. The main unit
will automatically update its readings at about 30-second inter-
vals.
If no signals are received, blanks "----" will be displayed and the
kinetic wave icon will show " ". Press [CHANNEL] and
[MEMORY] simultaneously to enforce another search for about
30 seconds. This is useful in synchronizing the transmission and
reception of the remote and main units.
Repeat this step whenever you find discrepancies between the
reading shown on the main unit and that on the corresponding
remote unit.
HOW TO USE THE TABLE STAND
OR WALL MOUNTING
The main unit has a removable table stand, which when installed,
can support the unit on a flat surface. Or you can remove the stand
and mount the unit on a wall using the recessed screw hole.
As for the remote unit, it comes with a wall-mount holder and a
removable stand. Use either to hold the unit in place.
Main unit
Wall-mount Table Stand
Remote unit
Wall-mount Table Stand
RMR183-e R2 OP 8/21/04, 6:22 PM5
Black

GB
6
HOW TO CHECK REMOTE AND
INDOOR TEMPERATURES
The indoor temperature is shown on the second line of the display.
As for the remote sites or channels, press [CHANNEL] to go from
one channel to another. The kinetic wave display on the channel
number indicates if the reception of that particular channel is in
good order.
If no readings are received from one particular channel for more
than two minutes, blanks “---” will be displayed until further
readings are successfully searched. Check if the remote unit
is sound and secure. You can wait for a little while or press
[CHANNEL] and [MEMORY] simultaneously to enforce an
immediate search. Of course no reading will be shown if no remote
unit is assigned to that channel.
If the temperature goes above or below the temperature measuring
range of the main unit or the remote unit (stated in specification),
the display will show “HHH” or “LLL”.
TEMPERATURE TREND
The temperature trend indicator on the screen shows the trend of
samplings collected at that particular remote site. Three trends,
rising, steady and falling, will be shown.
MAXIMUM AND MINIMUM
TEMPERATURES
The maximum and minimum recorded indoor temperatures and
those of outdoor channels will be automatically stored in memory.
To display them:
1. Select the channel to be checked.
2. Press [MEMORY] once to display the maximum temperature
and again the minimum temperature. The respective indicators,
MAX or MIN will be displayed.
Toclearthememory,holddown[MEMORY]for two seconds.The
maximum and minimum temperatures will be erased. If you press
[MEMORY] now, the maximum and minimum temperatures will
have the same values as the current ones until different readings
are recorded.
NOTE ON °C AND °F
The unit of temperature display is selected with the °C/°F slide
switch. Select °C for Centigrade or °F for Fahrenheit.
HOW TO READ
THE KINETIC WAVE DISPLAY
The kinetic wave display shows the signal receiving status of the
main unit. There are three possible forms:
Arrow
indicator
Temperature
Trend Rising Steady Falling
RMR183-e R2 OP 8/21/04, 6:22 PM6
Black

7
GB
DISCONNECTED SIGNALS
If without obvious reasons the display for a particular channel
goes blank, press [CHANNEL] and [MEMORY] to enforce an
immediate search. If that fails, check:
1. The remote unit of that channel is still in place.
2. The batteries of both the remote unit and main unit. Replace as
necessary.
Note: When the temperature falls below freezing point, the
batteries of outdoor units will freeze, lowering their voltage
supply and the effective range.
3. The transmission is within range and path is clear of obstacles
and interference. Shorten the distance when necessary.
TRANSMISSION COLLISION
Signals from other household devices, such as door bells, home
security systems and entry controls, may interfere with those of
this product and cause temporary reception failure. This is normal
and does not affect the general performance of the product. The
transmission and reception of temperature readings will resume
once the interference recedes.
CALENDAR AND ALARM TIME DISPLAY
The calendar and alarm time share the same section of display. The
calendar is displayed in day-month format. When the calendar is
displayed, pressing [ALARM] once will change the display to the
alarm time. Another press on the button will activate the alarm. A
third press will deactivate it.
To display the calendar, press [MODE] once.
Calendar mode Alarm mode
ABOUT RADIO RECEPTION
The RMR183/RMR183U is designed to automatically synchronize
its calendar clock once it is brought within range of the Frankfurt
DCF77radio signal. (Rugby MSF-60 Radio signal forUKversion).
When the RMR183/RMR183U is within range, the radio-con-
trolled mechanism will override all manual settings.
When the unit is receiving radio signal, the radio-reception Signal
will start to blink. Generally, complete reception take 2 to 10
minutes depending on the strength of the radio signal.
The unit is in searching mode.
Temperature readings are
securely registered.
No signals.
RMR183-e R2 OP 8/21/04, 6:22 PM7
Black

GB
8
Day-of-the-week
Language Monday Tuesday Wed. Thursday Friday Saturday Sunday
English
German
French
Italian
Spanish
When the reception is complete, the radio-reception Signal will
stop blinking.
For better reception, place the unit away from metal objects and
electrical appliances to minimize interference.
If you wish to disable the auto-reception feature, press the [ ] and
[ ] buttons simultaneously for two seconds. The radio-reception
Signal[ ]willdisappear.The unit will not respond to radio signals.
To enable the feature again, hold down the [ ] and [ ] buttons
again. The radio-reception signal will start blinking to initiate
reception automatically.
HOW TO SET THE CALENDAR CLOCK
MANUALLY
When the calendar is displayed, press [MODE] for two seconds.
The month digits will start to blink.
Enter the month using the [ ] and [ ] buttons. Hold down either
button to rapidly increase or decrease the value.
Press [MODE] to confirm and proceed to set the day, display
language, day-of-the-week, hour and minute.
For the display language, you can choose between English (E),
German (D), French (F), Italy (I), Spanish (S).
The day-of-the-week display for the languages is as follows:
After setting the minutes, press [MODE] to return to normal
display. If changes are made on the minutes, the seconds will reset
and start from zero.
- Strong
- Weak
- No Reception
- Receiving
RMR183-e R2 OP 8/21/04, 6:22 PM8
Black

9
GB
TIME DISPLAY MODE
When the display is in calendar mode, press [MODE] once to
change between the hour, minute, seconds display to hour, minute,
Day-of-Week display.
Hour-Minute-Second Hour-Minute-Day
HOW TO SET AND ACTIVATE
THE ALARM
While in alarm mode, press and hold [ALARM] for two seconds
the hour digits will flash.
Enter the value for the hour digits. Press [ALARM] to confirm and
go to the minute digits. Enter the value and press [ALARM] to
confirm.
The alarm is automatically activated. To deactivate it, press
[ALARM]once.
ALARM FUNCTION
When the alarm is active, it will go off at the set time with the
ALARM ON icon flashing.
The crescendo function allows the alarm to start off gently and
step up its intensity in three steps. Without interruption, the
alarm will go off for a minute and will go off once again after
approx. 8 minutes.
To stop the alarm, press any key (except [MEMORY] and
[CHANNEL] ) .
PRECAUTIONS
This product is engineered to give you years of satisfactory service
if you handle it carefully. Here are a few precautions:
1. Do not immerse the unit in water.
2. Do not clean the unit with abrasive or corrosive materials. They
may scratch the plastic parts and corrode the electronic circuit.
3. Do not subject the unit to excessive force, shock, dust,
temperature or humidity, which may result in malfunction,
shorter electronic life span, damaged battery and distorted
parts.
4. Do not tamper with the unit's internal components. Doing so will
invalidate the warranty on the unit and may cause unnecessary
damage. The unit contains no user-serviceable parts.
5. Only use fresh batteries as specified in the user's manual. Do not
mix new and old batteries as the old ones may leak.
6. Always read the user's manual thoroughly before operating the
unit.
SPECIFICATIONS
Temperature Measurement
Main unit
Indoor Temperature measurement
Operating range : -5.0°C to +50.0°C
(23.0°F to 122.0°F)
RMR183-e R2 OP 8/21/04, 6:22 PM9
Black