Orion RNK22SNH User manual

VIDEO WALL SOLUTION
(22~82 inches)
Installation and User's Guide
All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein

1. SAFETY INSTRUCTION
Follow this safety instruction to use the monitor properly and prevent the damages.
Keep this user’s guide book for later use.
This safety instruction has “Warning” & “Caution” as below
Warning - If the user does not follow this instruction,
it may cause the serious damage to the user.
Caution - If the user does not follow this instruction, it may cause the slight
damage to the user or cause some damages to the monitor.
Warning
Keep away the monitor from the
direct sunlight and a heating appliance.
Never push objects of any kind into
this product as they may result in
a risk of fire or electric shock.
Connect the power code to the wall
outlet tightly. If the power code or plug
are defective and the wall outlet is not
tight, please do not use them.
Never remove the back over and
touch the inside of the monitor.
If you need a service, please
contact the service center.
2
Installation and User's Guide

Warning
Do not install this monitor on the outside
and near water. If may cause damage to
the product, electric shock and fire.
For cleaning do not use liquid cleaners.
Never touch the power plug with wet-hands.
When lightning and thundering, unplug the
monitor from the wall outlet and never touch
it.
When smoking and noising from the monitor,
unplug the product from the wall outlet and
contact a service center.
Unplug this product from the wall outlet, when
It does not operate for a long time.
W
WA
AR
RN NI
IN NG
G:
:
How to fix
Do not open this product as it contains high voltage inside.
It may create an electric shock.
It the user disassembles and remove the back cover, it does not make sure
to make up for the damages and do a service and exchange the monitor.
3
Installation and User's Guide

Cautions
Install this monitor some distance
From the wall and do not install unless
Proper ventilation is provided.
Place this product on a stable place.
If not, it may fall, causing serious
Damages to the monitor and people.
The openings must not be blocked by
curtain, rug or other similar surface.
Before carrying the monitor, tum it off and
Unplug the signal cables and the power code
From the wall outlet.
When carrying this monitor, be careful
not to damage the panel and drop it
It may cause some trouble.
Take the power plug out from the wall
outlet.
Do not pull the cable. It may snap the inner-
wires and cause overheating and fire.
4
Installation and User's Guide

5
Installation and User's Guide
Cautions
Install this monitor about 50cm far from
the eyes and an angle of 0~15 degrees
below eyes. Too close installation may
cause having weak sight.
Do not press the LCD panel with hands or
the sharpened material hardly.
Do not use the chemical liquid for cleaning.
It may cause fading and breakage.
For cleaning, unplug the monitor from the
Wall outlet. Do net use the liquid cloth.
Use the soft cloth.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR WATER.
Instructions for Disposal of Electrical and Electronic Equipment in Private
Households
Disposal of used Electrical and Electronic Equipment
(Applicable in the European Union and other European countries with garbage separate
disposal and collection methods)
This symbol on the product, or in the related documents in the package, indicates that this
product shall not be treated as normal household waste. Instead, it should be taken to a proper
applicable collection point or depot for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent possible negative consequences for
the environment and human health, which could otherwise be caused by inappropriate waste handling of
this product. The recycling of materials will help to conserve natural resources.
For more detailed information about recycling of this product, please contact your local city authority, your
household waste disposal service or the place where you purchased the product.

2. FCC RF INTERFERENCE STATEMENT
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures.
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio, TV technician for help.
● Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void
the users authority to operate such equipment.
DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio
interference regulation of Canadian Department of communications.
6
Installation and User's Guide

2
1. SAFETY INSTRUCTION
1-1 Warning
1-2 Caution
6 2. FCC STATEMENT
3-1 Parts
3-2 How to Install
23 7. TROUBLESHOOTING
8
3. INSTALLATION
4-1 Mode Setting
4-2 Menu Setting
13 4. OSD MENU SETTING
21
5. FEATURES
22 6. MECHANICAL DRAWING
TABLE OF CONTENTS
7
Installation and User's Guide

3. INSTALLATION
3-1 Parts
LCD Monitor & Keypad
UTP Cable VGA Cable Serial Cable
Joint Bracket
Trigger Cable Power Cable Remote Controller
Battery Install CD User Manual
(Only 40 inches or more)
8
Installation and User's Guide

3-2 How to Install
UTP Cable (1.5m)
If you want to replace with a longer cable Please purchase separately
This KEYPAD is attached to a magnet, so you can freely paste
SHORT KEY FUNCTION
KEYPAD CONTROLLER
OSD KEY FUNCTION
On/off the OSD menu or exit the source selection menu
Move the cursor to choose on the OSD menu
Select the source on the INPUT menu
Move up the cursor to choose on the OSD menu
Activate the auto adjustment of RGB source
Control down on the OSD menu or move to the previous menu
Volume down
Select the OSD menu
Control up on the OSD menu
Volume up
Turn the power ON or OFF. There will be a few seconds delay before the
display appears. The power LED (next to the power switch) lights with green
when the power is turned ON. The power is turned off by pressing the power
switch again and the power LED goes red.
9
Installation and User's Guide

CONNECTION
1 2 3 4 5 6
1 2 3 4 5 6 14
7 8 9 10 11 12 13
HDMI
22 inches
40~82 inches
1VIDEO-2 IN / OUT
HDMI Signal input / loop output VIDEO-2 Signal input / loop output
8
DVI
2AUDIO (VIDEO-1)
DVI Signal input / loop output Stereo audio input for VIDEO-1
9
VGA
3AUDIO (VIDEO-2)
VGA (PC RGB) Signal input / loop output Stereo audio input for VIDEO-2
10
RS-232 IN / OUT
4TRIGGER
SERIAL Cable input / output for RS-232 TRIGGER Signal input
11
KEYPAD
5SPEAKER OUT
UTP Cable input for KEYPAD Stereo speaker output
12
AUDIO (PC)
6AC POWER
Stereo audio input for VGA AC 100-240V input
13
VIDEO-1 IN / OUT
7DC24V
VIDEO-1 Signal input / loop output DC 24V (Adapter) input
14
10
Installation and User's Guide

CONFIGURE THE VIDEO WALL
CENTER
Assemble the JOINT BRACKET
using four M4 screws.
SIDE
Assemble the JOINT BRACKET
using two M4 screws.
1. You can combine two or more monitors, and configure the VIDEO WALL.
2. If you want to configure VIDEO WALL, please contact your dealer or
a professional installer.
3. JOINT BRACKET helps to easily adjust the VIDEO WALL. (Supplied with monitor)
HDMI OUT
HDMI IN
DVI OUT
DVI IN
VGA OUT
VGA IN
RS-232 OUT
RS-232 IN
VIDEO1 OUT
VIDEO1 IN
VIDEO2 OUT
VIDEO2 IN
CABLES CONNECTION
* Cable connection order, it may be different
from the order of the 'SET ID' or 'SEQUENCE'
(Refer to page 15~17)
1st MONITOR
2nd MONITOR
3rd MONITOR
4th MONITOR
* Please install the VWCP (Video Wall Control Program) for remote control of the monitors through the computer.
For information about installing and using VWCP, please refer to the installation disk that came with the monitor.
11
Installation and User's Guide

REMOTE CONTROLLER
MODE SELECT MENU
VIDEO 1 (Only 40 inches or more)
Select VIDEO 1 mode
VIDEO 2 (Only 40 inches or more)
Select VIDEO 2 mode
VGA (RGB)
Select VGA mode
DVI
Select DVI mode
HDMI
Select HDMI mode
POWER
Turn ON / OFF the monitor
MUTE
Turn ON / OFF the sound
AUTO
Auto adjust position of the screen (in VGA mode)
COLOR TEMPERATURE
Select color temperature of the screen
SCAN MODE
Select the scan mode of the screen
VOL- / VOL+
Increase / Decrease the volume level
MENU / EXIT
Activate and exit the OSD menu
STILL
Freeze the current image
KEY LOCK
Locking the button (Prevent operation)
S. SET
Select between main and PIP audio input
PIP
Activates PIP/PBP mode
P. INPUT
Select an input source for PIP mode
P. LOCATION
Select a location for PIP mode
P. SIZE
Select a size for PIP mode
P. SWAP
Swap between main and PIP input
A
OSD CONTROL MENU
B
PIP CONTROL MENU
C
POWER MUTE
VIDEO1 VIDEO2
VGA AUTO COLOR TEMP
DVI HDMI
S.SET
SCAN MODE PIP
MENU/EXIT
P.INPUT P.LOCATION
P.SWAP STILL
P.SIZE
KEY LOCK
VOL- VOL+
A
B
C
12
Installation and User's Guide

4. OSD MENU SETTING
4-1 Mode Setting
VIDEO1 Select VIDEO1 Mode (Only 40 inches or more)
VIDEO2 Select VIDEO2 Mode (Only 40 inches or more)
RGB PC Select VGA Mode
DVI Select DVI Mode
HDMI Select HDMI mode
VIDEO1
VIDEO2
√RGB PC
DVI
HDMI
▼/▲:MOVE ▶:ENTER
INPUT
1. Use Source button and then ▲ or ▼ button to move the source.
2. Press the ► button to select the source.
3. Press the MENU/EXIT button to exit the INPUT menu.
13
Installation and User's Guide

4-2 Menu Setting
PICTURE
ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE
CONTRAST Adjust the contrast level of color All modes
BRIGHTNESS Adjust the brightness level of color All modes
COLOR Adjust the depth of color VIDEO, HDMI
TINT Adjust the tint of color (only NTSC signal) VIDEO, HDMI
SHARPNESS Adjust the sharpness of picture VIDEO, HDMI
PEAKING CONTROL Adjust the sharpness of outline HDMI
COLOR TEMP Set the color temperature of screen
(MEDIUM, WARM, USER, COOL) All modes
60%
50%
50%
50%
50%
50%
MEDIUM
PICTURE
CONTRAST 60%
BRIGHTNESS 50%
COLOR 50%
TINT 50%
SHARPNESS 50%
PEAKING CONTROL 50%
COLOR TEMP ◀ MEDIUM
RED 128
GREEN 128
BLUE
▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*
128
PICTURE
SCREEN
SETUP
RGB
SETUP
SETUP
CYCLE
TRIGGER
▶
1. Press the MENU key to access menu.
2. Use the ▲ or ▼ key to choose PICTURE.
3. Press the ► key to enter the PICTURE menu.
4. Use the ▲ or ▼ key to choose an item of PICTURE.
5. Use the ◄ or ► key to adjust the setting on a selected item.
14
Installation and User's Guide

SCREEN
ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE
H MONITORS
Set the total number of horizontally installed monitors
on the video wall situation
(01 ~ 99) All modes
V MONITORS Set the total number of vertically installed monitors
on the video wall situation
(01 ~ 99) All modes
SEQUENCE Set the sequence of installed monitors on the video
wall situation
(01 ~ 99) All modes
H GAP Set the horizontal gap between adjacent panels
caused by bezel width
(00 ~ 99) All modes
V GAP Set the vertical gap between adjacent panels
caused by bezel width
(00 ~ 99) All modes
SCAN MODE Select the scan mode of the screen
(FULL, REAL,*UNDER, OVER, 4:3)
*UNDER : It does not appear in HDMI mode
All modes
01
01
01
00
00
FULL
PIP Activate PIP/PBP mode (OFF, ON, DW1, DW2)
(Only 40 inches or more) HDMIOFF
SCREEN
SCAN MODE
PIP
PIP INPUT
PIP SWAP
PIP SIZE
PIP LOCATION
PICTURE
SCREEN
SETUP
RGB
SETUP
SETUP
CYCLE
TRIGGER
◀ R/B ▶
◀ SMALL ▶
▶
◀ VIDEO2 ▶
◀ OFF ▶
◀ FULL ▶
SEQUENCE
H GAP
V GAP ◀ 00 ▶
◀ 00 ▶
◀ 01 ▶
H MONITORS
V MONITORS ◀ 01 ▶
◀ 01 ▶
▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*
1. Press the MENU key to access menu.
2. Use the ▲ or ▼ key to choose SCREEN.
3. Press the ► key to enter the SCREEN menu.
4. Use the ▲ or ▼ key to choose an item of SCREEN.
5. Use the ◄ or ► key to adjust the setting on a selected item.
15
Installation and User's Guide

SCAN MODE
ex) In case of 3X2 Video Wall Setting
REAL : Display original images entered from the source intactly
UNDER : Display the image on the smaller area than the screen
Original image is fully displayed.
OVER : Display the image on the broader area than the screen
Original Image is cut off on the edge.
4:3 : Display the image to 4:3 aspect ratio
PIP
Default Setting is OFF and changeable to ON, DW1 and DW2 PIP/PBP modes.
OFF : PIP/PBP modes are not activated.
ON : Switch on PIP/PBP mode
DW1 : change to Double Window mode 1
DW2 : change to Double Window mode 2
After selecting PIP/PBP modes, following items are activated.
PIP INPUT : Select an input source for PIP image (VIDEO 1, VIDEO 2)
PIP SWAP : Swap main picture and sub picture
PIP SIZE : Select the size of PIP image (SMALL, NORMAL, LARGE)
PIP LOCATION : Select the position of PIP image (R/B, L/B)
SEQUENCE numerical order
1 2 3 4
5 6 7 8
9 10 11 12
13 14 15 16
H MONITORS : 03
V MONITORS : 02
SEQUENCE : 01
H MONITORS : 03
V MONITORS : 02
SEQUENCE : 02
H MONITORS : 03
V MONITORS : 02
SEQUENCE : 03
H MONITORS : 03
V MONITORS : 02
SEQUENCE : 05
H MONITORS : 03
V MONITORS : 02
SEQUENCE : 06
H MONITORS : 03
V MONITORS : 02
SEQUENCE : 04
H GAP : 01
V GAP : 01
16
Installation and User's Guide

SETUP
SETUP
INPUT
LANGUAGE
AUDIO MUTE
AUDIO OUT
NOISE REDUCTION
OSD TIME
PICTURE
SCREEN
SETUP
RGB
SETUP
SETUP
CYCLE
TRIGGER
DEFAULT ▶
SET ID ◀ 01 ▶
KEY LOCK ◀ OFF ▶
LINE SHIFT ◀ OFF ▶
◀ ON ▶
◀ OFF ▶
◀ INTERNAL ▶
◀ ENGLISH ▶
◀ VIDEO1 ▶
▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*
15s
FAN CONTROL
FAN AUTO REF
◀ AUTO ▶
42c
FAN SPEED
CURRENT TEMP
◀ NORMAL ▶
42c
ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE
INPUT Select the input source for main picture All modes
LANGUAGE Set the language of OSD
(ENGLISH, ITALIAN, FRENCH, SPANISH, GERMAN)
All modes
AUDIO MUTE Turn on/off the audio output All modes
AUDIO OUT Select the speaker for audio output
(INTERNAL, EXTERNAL) All modes
NOISE REDUCTION Set the noise reduction mode All modes
OSD TIME Set the time duration of OSD menu (5~30s) All modes
CURRENT TEMP Display the current temperature All modes
ENGLISH
OFF
INTERNAL
ON
15s (seconds)
DEFAULT Factory default setting All modes
SET ID Allocate an ID of the set for RS-232 control All modes01
KEY LOCK Lock the key action (Prevent operation) All modesOFF
LINE SHIFT Move the image a little instantaneously to protect
the screen All modesOFF
FAN CONTROL Select the control method of FAN (AUTO, ON, OFF) All modesAUTO
FAN AUTO REF Set the reference temperature for automatic FAN
control (20~60c) All modes42c (celsius)
FAN SPEED Select the speed of FAN (NORMAL, FAST, SLOW) All modesNORMAL
1. Press the MENU key to access menu.
2. Use the ▲ or ▼ key to choose SETUP.
3. Press the ► key to enter the SETUP menu.
4. Use the ▲ or ▼ key to choose an item of SETUP.
5. Use the ◄ or ► key to adjust the setting on a selected item.
17
Installation and User's Guide

RGB SETUP (ONLY RGB PC MODE)
RGB SETUP
H-POSITION
V-POSITION
CLOCK
PHASE
AUTO ADJUST
POWER SAVING
PICTURE
SCREEN
SETUP
RGB
SETUP
SETUP
CYCLE
TRIGGER
AUTO REPEAT ◀ OFF ▶
▶
◀ OFF ▶
▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*
100%
0%
0%
0%
ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE
H-POSITION Adjust the horizontal position of the screen RGB PC
V-POSITION Adjust the vertical position of the screen RGB PC
CLOCK Adjust the clock of the screen RGB PC
PHASE Adjust the phase of the screen RGB PC
AUTO ADJUST Adjust all of above items for suitable screen RGB PC
POWER SAVING Adjust the power saving mode RGB PCOFF
AUTO REPEAT Repeat AUTO ADJUST action automatically RGB PCOFF
To cancel KEY LOCK mode
Remote Controller : Press KEY LOCK button
Keypad : Press ▲ & ◄ buttons simultaneously
1. Press the MENU key to access menu.
2. Use the ▲ or ▼ key to choose RGB SETUP.
3. Press the ► key to enter the RGB SETUP menu.
4. Use the ▲ or ▼ key to choose an item of RGB SETUP.
5. Use the ◄ or ► key to adjust the setting on a selected item.
18
Installation and User's Guide

CYCLE SETUP (ONLY 40 INCHES OR MORE)
ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE
CYCLE TIME Adjust the time interval to display selected mode All modes
CYCLE
Display selected modes sequentially in set cycle time All modes
VIDEO1 Choice as to whether to cycle of VIDEO1 mode All modes
VIDEO1 Choice as to whether to cycle of VIDEO2 mode All modes
RGB PC Choice as to whether to cycle of RGB PC mode All modes
DVI Choice as to whether to cycle of DVI mode All modesOFF
OFF
OFF
OFF
OFF
10s (seconds)
HDMI Choice as to whether to cycle of HDMI mode All modesOFF
1. Press the MENU key to access menu.
2. Use the ▲ or ▼ key to choose CYCLE SETUP.
3. Press the ► key to enter the CYCLE SETUP menu.
4. Use the ▲ or ▼ key to choose an item of CYCLE SETUP.
5. Use the ◄ or ► key to adjust the setting on a selected item.
CYCLE SETUP
CYCLE TIME
CYCLE
VIDEO1
VIDEO2
RGB PC
DVI
PICTURE
SCREEN
SETUP
RGB
SETUP
SETUP
CYCLE
TRIGGER
HDMI
◀ OFF ▶
◀ OFF ▶
◀ OFF ▶
◀ OFF ▶
◀ OFF ▶
◀ OFF ▶
▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*
10s
19
Installation and User's Guide

TRIGGER (ONLY 40 INCHES OR MORE)
TRIGGER
TRIGGER MODE
TRIGGER INPUT
TRIGGER DWELL
PICTURE
SCREEN
SETUP
RGB
SETUP
SETUP
CYCLE
TRIGGER
◀ OFF ▶
◀ VIDEO1 ▶
▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*
10s
ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE
TRIGGER MODE Set the trigger mode All modes
TRIGGER INPUT Select the input source of trigger mode
(VIDEO1, VIDEO2) All modes
TRIGGER DWELL Set the display time of trigger mode (10~60s) All modes
OFF
VIDEO1
10s (seconds)
1. Press the MENU key to access menu.
2. Use the ▲ or ▼ key to choose TRIGGER.
3. Press the ► key to enter the TRIGGER menu.
4. Use the ▲ or ▼ key to choose an item of TRIGGER.
5. Use the ◄ or ► key to adjust the setting on a selected item.
INPUT SIGNAL MODE RESOLUTION VERTICAL FREQUENCY (Hz)
VGA / DVI
VGA 640X480 60 / 72 / 75
VGA 720X400 70
SVGA 800X600 56 / 60 / 75
XGA 1024X768 60 / 75
SXGA- 1280X960 60
SXGA 1280X1024 60 / 75
WXGA 1366X768 60
WXGA+ 1440X900 60
FHD 1920X1080 60
HDMI
SDTV 480i 720X480 30
SDTV 576i 720X576 25
EDTV 480p 720X480 60
EDTV 576p 720X576 50
HDTV 720p 1280X720 50 / 60
HDTV 1080i 1920X1080 25 / 30
HDTV 1080p 1920X1080 50 / 60
INPUT SIGNAL MODE TABLE
20
Installation and User's Guide