Ortur Y-axis User manual

1
User Manual of
Y Axis Rotary Roller
Dongguan Ortur Intelligent Technologies Co., Ltd.

2
(EN)Address: No. 56 Maxin Road, Changping Town, Dongguan 523565, Guangdong Province, China
(FR)Adresse: No. 56 Route Maxin, Changping Town, Dongguan 523565, Province de Guangdong, Chine
(DE)Adresse: 56 Maxin Road, Stadt Changping, Dongguan 523565, Provinz Guangdong, China
(IT)Indirizzo: No. 56 Maxin Road, Città Changping, Dongguan 523565, Provincia del Guangdong, Cina
(ES)Dirección: 56 Maxin Road, Ciudad Changping, Dongguan 523565, Provincia de Guangdong, China

1
Brief Introduction
 This Y-axis Rotary Roller is used for laser engraving on cylindrical
objects.
 This Y-axis Rotary Roller is an accessory part of Laser Engraver,
cannot be used alone.
Attention
 This Y-axis Rotary Roller could be used with other brands of laser
engraver, but it does not guarantee a perfect match.
 If user modifies the Y-axis Rotary Roller without permission, we would
not be responsible.

2
Assembly Procedure
1. Assemble the Frame and Motor by 4 x M3*8 screws and 4
x M5*10 screws
2. Assemble the Idle Pulley
M5*10 Screw ×4Pcs
M3*8 Screw ×4Pcs
M5 Nut ×2Pcs
5.3mm Spacer ×2Pcs
M5 Locknut ×2Pcs
Bearing ×4Pcs
M5*20 Screw ×2Pcs

3

4
3. Assemble Roller
Bearing ×2Pcs
Bearing ×2Pcs
M5*10 Screw ×4Pcs
M5 Nut ×4Pcs
Note: The screws here should not be tightened for
now, and the installation gap should be reserved.

5
M5 Nut ×4Pcs
M5*10 Screw ×4Pcs

6
4. Assemble Timing Belt Pulleys.
5. Last Step.
25
T
eeth Timing Belt Pulley
×
2Pcs
16
T
eeth Timing Belt Pulley
×
1
Pc

7
Insert the timing belt, adjust the
position of each Timing Belt Pulley,
and use the hex wrench to tighten the
internal fixing screw
.

8
The distance between the two rollers can be adjusted
according to actual needs

9
Setting Procedure
Turn off the Automatic Home function. (Please skip this step
if your laser engraver does not have this function.)
1.Turn on the laser engraver, open
the LaserGRBL software on
computer, and connect the laser
engraver
.
2.Unlock the laser engraver.
2.Unlock the laser engraver.

10
3.Open Grbl Configuration.

11
4. Change the value here to 0, to turn off
the Automatic Return to Origin function.
5.Write data to the main
board.
6.Close the window.

12
1. The installation method for marching with
cantilever laser engraver：
1.1. Place the subject as shown in the figure below, and connect with
the laser engraver by a 500MM extension cable.
Unplug the Y Motor Cable, and
connect this Y Motor Cable and
the Y-axis Rotary Roller by the
extension cable
.
Heighten the laser
engraver according to
the height of the object.

13
1.2. Adjust the position and laser focus, then start engraving.
WARNING: Must wear eye protection (Laser goggles) before
operating laser !!!
The laser spot should be aligned with
the ape
x
of the cylinder object
.

14
2. The installation method for marching with
frame laser engraver：
2.1. Place the subject as shown in the figure below, and connect with
the laser engraver
Heighten the laser
engraver according to the
height of the object.

15
2.2. Adjust the position and laser focus, then start engraving.
PS. DO wear eye protection (Laser goggles) before operating laser !!!
Unplug the Y Motor Cable, and
connect this Y Motor Cable and
the Y-axis Rotary Roller by the
extension cable
.
The laser spot should be aligned with
the apex of the cylinder object.