Osaki OS-Hiro LT User manual

OS - Hiro LT

IMPORTANT SAFETY INSTRUCTIONS
2-3
4
5
6-7
8
10-11
13-18
21
19
20
22
12
9
FCC Radiation Exposure Statement
Industry Canada Notice
Chair Installation

IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
DANGER
When using an electrical appliance, basic precautions should always be followed,
including the following:
Read all instructions before using (this appliance).
To reduce the risk of electric shock:
• Always unplug this appliance from the electrical outlet immediately after using and
before cleaning.
WARNING To reduce the risks of burns, fire,electric shock or injury to
persons:
• An appliance should never be left unattended when plugged in. Unplug from
outlet when not in use, and before putting on or taking off parts.
• Close supervision is necessary when this appliance is used by, on, or near
children, invalids, or disabled persons.
• Use this appliance only for its intended use as described in this manual. Do not
use attachments not recommended by the manufacturer.
• Never operate this appliance if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return the
appliance to a service center for examination and repair.
• Do not carry this appliance by supply cord or use cord as a handle.
• Keep the cord away from heated surfaces.
• Never operate the appliance with the air openings blocked. Keep the air
openings free of lint, hair, and the like.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or where oxygen
is being administered.
• To disconnect, turn all controls to the off position, then remove plug from outlet.
• Keep children away from extended foot support.
• Connect this appliance to a properly grounded outlet only. See Grounding
Instructions.
• Use heated surfaces carefully. May cause serious burns. Do not use over
insensitive skin areas or in the presence of poor circulation. The unattended use
of heat by children or incapacitated persons may be dangerous.
• Do not operate under blanket or pillow. Excessive heating can occur and cause
fire, electric shock, or injury to persons.
• Never use pins or other metallic fasteners with this appliance.
• Carefully examine the covering before each use. Discard the appliance if the
covering shows any sign of deterioration, such as checking, blistering, or cracking.

3

LED Light
Seat Cushion
6
5
1
4
7
2
3

Shoulder side
air massage section
Arm & hand
air massage section
Lumbar heater
Legrest air
massage section
Foot roller

8

When placing a mat under the unit, the size of the mat should be sufficient
to cover the areas where the unit touches and where the legrest could touch
the floor, as shown in the dia gram on the above.
9

10

11

SPEED
INTENSITY
SHOU LD ER HAND
FOOTSEAT
FU LL AIR
STRENGTH
LED
WIDTH
ROLLE R UP
ROLLE R DO WN
SPO T
PART IA L
12

3.
Press this button to light up the LCD screen. Press any massage function button
to start massage. This will initiate the timer function. Press this button again to
stop all massage functions, massage chair will return to its original position.
PAUSE
2. TIMER
Time interval Control Button
When a massage function is activated,the timer is preset at 15 minutes. Every
single press on this button will change the timer interval in the sequence of 20 >
25 > 30 > 5 > 10 > 15 > 20 minutes.
Press this button once to halt current massage function and countdown timer.
During pause mode, the pause button will be blinking.
Press this button again to cease the Pause function and resume previous massage
function as well as countdown timer.
5. LEGREST RECLINE AND RESTORE
Angle Adjustment Button for Leg rest.
Keep pressing either button until the leg rest reaches your desired position.
4. Zero Gravity
Press this button to active the Zero Gravity function,press again to return to idle
position.
Zero Gravity button is NOT controllable during auto programs of Swedish
and Thai.
Note:
13

14
6. CHAIR RECLINE AND RESTORE
Keep pressing to comfortably lay flat or to restore the chair to its original
position.
Full body Auto massage program
7.GENTLE
8.RELAX
9.THERAPY
10.VIGOROUS
11.DEMO
12.SWEDISH
13.THAI
14 . CHINESE
15.LEGREST LENGTH ADJUSTMENT BUTTON
These two control buttons can adjust the length of chair legrest.
Press or once to lengthen or shorten the chair legrest.
1 ) Please press the button gently to avoid sticking the button.
2 ) When ZGR is activated before any program , the chair will scan and adjust the
length of leg rest automatically.
16.WIDTH
The Width Adjustment Button for Tapping, Clapping,Shiatsu and Rolling function.
When Tapping, Clapping,Shiatsu or Rolling function is engaged, every single press
on this button will change the massage width interval in the sequence of
Narrow > Medium > Wide in cycle.
17.Spot
The Spot Back massage
This button allows the user to select spot massage for any part on the back.
Press this button activate spot massage at the required location.
Press this again to switch to partial function.
18.Partial
The Partial Back massage.
Press this button to switch to partial function.
Notes :

21.KNEADING
Kneading function Start Stop Control Button -5 levels of strength to be adjusted
Press this button to activate rhythmic mode 1 Kneading function for a full back
massage at medium strength. Press the button again to activate mode 2 Kneading
function. Press the button for the third time to stop Kneading function and switch to
mode 1 Swedish function.
21.SWEDISH
Swedish function Start/Stop Control Button -5 levels of speed to be adjusted.
When mode 2 Kneading function is engaged, press this button to activate rhythmic
mode 1 Swedish function for a full back massage at medium speed. Press this
button again to activate mode 2 Swedish function. Press once more to stop the
Swedish function. To activate Swedish function directly, press this button 3 times
during idle mode.
19/20.Roller up/ Roller down
The massage position adjustment button for spot and partial massage.
When the manual or automatic shoulder scanning can't meet individual, requirements,
you manual fine tune the shoulder height location by pressing up/ down button within
sound 10 seconds. Once appropriate location found release the key, the final position
will be lock.
In the spot or partial massage,you can also use these two buttons to adiust
the massage position.
Manual Massage Program
Note:
22.TAPPING
Tapping function Start/Stop Control Button-3 levels of width, 5 levels of speed to be
adjusted. Press this button to activate rhythmic mode 1 Tapping function for a full
back massage at medium speed. Press the button again to activate mode 2 Tapping
function. Press the button for the third time to stop Tapping function and switch to
mode 1 Shiatsu function.
15

22.SHIATSU
Shiatsu function Start/Stop Control Button - 3 levels of width, 5 levels of speed to be
adjusted. When mode 2 Tapping function is engaged, press this button to activate
rhythmic mode 1 Shiatsu function for a full back massage at medium speed. Press
this button again to activate mode 2 Shiatsu function. Press once more to stop the
Shiatsu function. To activate Shiatsu function directly, press this button 3 times
during idle mode.
23.CLAPPING
Clapping function Start/Stop Control Button -3 levels of width,5 levels of speed to be
adjusted. Press this button to activate rhythmic mode 1 Clapping function for a full
back massage at medium speed. Press the button again to activate mode 2 Clapping
function.Press the button for the third time to stop Clapping function and switch to
Rolling function.
23.ROLLING
Rolling function Start/Stop Control Button -3 levels of width to be adjusted.
When mode 2 Clapping function is engaged, press this button to activate Rolling
function for a full back massage.Press this button again to stop the Rolling function.
To activate Rolling directly, press this button 3 times during idle mode.
This function cannot perform "Spot" massage function.
24.Foot Roller
Foot roll function Start/Stop Control Button.
Press once to activate the roller on foot, press again to stop the foot roll function.
25.LED LIGHTING
LED Lighting Function Start/Stop Control Button.
Press this button to activate LED lighting function. Press again to stop the LED
Lighting function.
Note:
16

26.HEAT
Lumbar Heat function Start/Stop Control Button.
Press this button to activate lumbar heat function, press this button again to stop
the Heat function.
During Auto Program mode, pressing this button can also disable/enable the
Heat function.
27.Intensity
The Intensity Adjustment Button for Alr-pressure-5 levels of intensity to be adjusted.
After activating the air-pressure function(Auto and Manual), press this button to
adiust the intensity in the cycle.
28.SPEED
The Speed Adjustment Button for Tapping, Clapping, Swedish and Shiatsu function.
When Tapping, Clapping, Swedish or Shiatsu function is engaged, every single press
on this button will change the massage speed interval in the sequence of " Lv1 > LV2
> LV3 > LV4 >Lv5 " in cycle.
29.STRENGTH
The Strength Adjustment Button for kneading function.
When Kneading function is engaged, every single press on this button will change
the massage speed strength interval in the sequence of " Lv1 > Lv2 > Lv3 > Lv4 > Lv5 "
in cycle.
30.SHOULDER
Shoulder Air Squeeze Massage Control Button -5 levels of intensity to be adjusted.
Press this button once to activate rhythmic air massage at shoulder Press this button
again to stop the function.
31.BACK & SEAT
Back and Seat Air Squeeze Massage Control Button 5 levels of intensity to be
adjusted. Press this button once to activate rhythmic air massage at back and seat.
Press this button again to stop the function.
Setting Air Squeeze
Note:
17