Overmax Multipic 2.4 User manual

User Manual
Instrukcja obsługi
Multipic 2.4 EN
PL
NL
CR
HU

EN
Introduction
Dear customer!
Thank you for placing trust in us and choosing Overmax.
Thanks to the use of high-quality materials and modern solutions, we
provide you with a product perfect for everyday use. We are convinced that
the product will satisfy your requirements as it has been designed with
utmost care. Before you start using the product, please read this manual
carefully.
Should you have any remarks or questions concerning the product, please
do not hesitate to contact us:
[email protected]
Important:
Before using this projector, please read the manual carefully. Any wrong
operation may cause electric shock or fire. Please comply with the following
instructions when using and/or repairing the projector.
Keep this manual for future reference.
Warning:
1. Before you use the product, please read this manual carefully.
2. To assure stable power supply, please use a standard feeder cable
which satisfies local power supply network parameters.
3. Do not look into the lens when it operates.
4. When the projector is on, make sure air holes are not covered. For this
reason the device must not be placed on soft surfaces or be covered.
5. he projector is not waterproof and this is why you must not place any
reservoirs with liquids on it or near it, such as flower pots, vases, cups,
etc.

EN
6. The projector must be stored and used in a dry and clean place.
7. If you don’t use the device for a long time, switch it off and unplug.
8. When you move the product, please secure it with a film and other
materials supplied.
9. If you damage the projector, do not repair it on your own. Contact
the seller or manufacturer to report the defect.
Notes:
When using the projector, please follow the guidelines included in this
manual. In the event of any discrepancies between the manual and real
features of the product, the latter shall apply.
Outlook
1. Rear panel
1. USB-A port (input).
2. HDMI port (input)
3. Mini-Jack (audio output)
4. AV port (input)
5. IR signal receiver (remote control signal)
6. VGA port (input)

EN
2. Top panel
How to use the device:
3. Remote control
1. Go left
2. Go right
3. Go up
4. Go down
5. Menu/return key
6. Select source of video signal
7. Status LED
8. On/off key
1. On/off switch
2. Forward
3. Previous
4. Mute
5. Rewind
6. Play/pause
7. Stop
8. Select video source
9. Menu navigation directions
10. Options/return menu key
11. Numerical keypad
12. Edit numbers
13. Next
14. PVR function
15. Audio language selection
16. Programs guide
17. Confirm key
18. Exit/back
19. Switch between items
How to use the device:

EN
1. Power supply
2. Switching on and off
3. Sharpness and screen angle adjustment
Place the projector in a way that the lens is perpendicular to the wall
or board on which the image is to be displayed. Once the device has been
switched on, the main menu will be displayed:
To switch the projector on or off, set active position (-) of the power key
at the back of the housing (3). Press on/off key on the remote control or
projector (4).
Connect one tip of the feeder cable to the projector (1) and then another
plug to power supply network port (2).
To increase sharpness of the image, turn the
sharpness knob (2) located behind the lens (1) so that
the image gets sharper.
If the image is not displayed perpendicularly, it will
be distorted.
Distorted image in the shape of the trapezoid (see
figure below) can be adjusted with the use of a knob
(3).

EN
4. Language change
5. Connection to Wi-Fi network
a) Use directional keys on the remote control to select sections
(Settings) and confirm with (OK) key on the remote.
b) Select section (Advanced) and confirm your choice with (OK)
key.
c) Select section (Language). Use arrows on the remote control
(left, right) to set language.
d) Return to main menu by pressing (EXIT) key on the remote
control.
a) Use directional keys on the remote control to select sections
(Settings) and confirm with (OK) key on the remote.
b) Selection section (Network) and confirm your choice.
c) Selection section (Wi-Fi) and confirm your choice.
d) Select section (Scan) and confirm your choice. The projector will scan
available Wi-Fi networks and display a list of networks.
e) Select name of Wi-Fi network you want to connect to and confirm your
choice with (OK) key on the remote control.
f) If the network is secured with password, you will be required to enter it. Go
to the field (Password) and confirm your choice.
g) The display with show a virtual keypad which you can use to enter the
password. Use remote control keys to navigate it and confirm letters and
digits with (OK) key. Upper-case letters can be enabled by selecting and
choosing (ABC). Once you have entered a correct password, press (EXIT)

EN
on the remote to leave the keypad. Confirm the password by selecting
(Accept)/(Confirm) and press (OK).
h) To return to main menu, press (EXIT) key a few times on the remote
control.
The projector allows displaying image from various devices. Depending on
your device, you should use a relevant input at the back of the housing.
1. USB input – such devices as pendrive, external drive
2. HDMI input – such devices as PC, laptop, console, satellite receiver,
telephone (supporting MHL and only through a dedicated MHL cable).
3. Video-In (AV) input – such devices as console, satellite receiver.
4. VGA input – such devices as PC, laptop, satellite receiver.
If more than one video signal is connected to the
projector, you must select the device from which
the projector is to display the image.
a) Use directional keys on the remote control to select sections (Source) and
confirm with (OK) key on the remote.
b) You will see a list of video sources (described in previous point).
c) Use directional keys on the remote to select the source from which the
image is to be displayed and confirm your choice with (OK) key.
d) To return to the list of video sources, select (MENU) on the remote.
In video source selection section, you can also set image and sound
parameters:
Image: display mode (standard, soft, vivid), proportions (4:3, 16:9),
brightness, color, contrast, sharpness
6. Connection to multimedia source through a cable
7. Selection of video source

EN
To play multimedia from pendrive or external drive,
follow the steps below:
a) Connect the drive to USB-A port at the back
of the housing.
b) Use directional keys on the remote control to select
sections (Media) and confirm with (OK) key on the remote.
The projector is equipped with a wireless Wi-Fi connection unit which allows
displaying image from mobile device without cables. Only mobile devices
compatible with MIRACAST technology can transmit image to the projector.
If the drive has been detected properly, you will be able to browse its content
by categories: films, music, pictures, text.
The files in these categories may be browsed and displayed on the screen.
To navigate between them, use directional keys on the remote control and
confirm your choice with (OK) key.
8. Connection to external drive
9. Wireless video connection to mobile devices
Sound: sound mode (standard, messages, music, theater), bass, high tones,
balance, equalizer.

EN
a) Use directional keys on the remote control to select
sections (Miracast) if you use Android-based device,
compatible with Miarast. If you use Apple device with
iOS system, choose (iOS Cast). Once you have selected,
confirm it with (OK) key on the remote..
b) Enable Wi-Fi in mobile device.
c) Depending on the device, the connection through
„Miracast” may differ.
Android devices: search for settings defined as Miracast
or screen mirroring or connection with screen. Next enable searching for
active wireless screens. Then find a device called „ZYCast” and connect to it.
Apple devices with iOS system: Make sure the projector and device from
which you want to display image are connected to the same Wi-Fi network.
Enter the control panel and select screen mirroring, then find the device
called „ZYCast” and connect to it.
If you have any connection issues, return to Wi-Fi network connection
settings (described in point 5). Select (AUTO-IP) and confirm. Next return
to connection screen (iOS Cast) and repeat the steps on the phone.