PAC C2R-CHY4 User manual

Radio
Connection
Chart
(Read the Installation Notes before making
connections to the provided radio harness)
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White I Black Front L -input
Grey Front R + input
GreyI Black Front R -input
Green Rear L + input
Green I Black Rear L -input
Purple Rear R + input
Purple I Black Rear R -input
CAN
Interface
Connection
Chart:
Red Ace. Output
(1
amp)
Red I White
P.B.
Output(-)
Purple I White VSS Output (Pulse)
Orange I White Ilium.
Output(+)
Green Reverse Output (+)
White I Green
C2R-CHY4
Radio Replacement Interface
with
Nav
Outputs for all Chrysler
DodgeI Jeep CANbus Vehicles With
or
Without PremiumAudio Systems
Navigation
outputs
and
Amp
li
fier
Remote
Input
See
Chart
for
wire
color
des
c
ri
ptio
ns
.
~
r:=;
~~
~---Jr
-
......
__
-1
~
~
"
Radio
Specific
Steering
~
8'
Wheel
Control
Interface
••
cl'
•
(Sold
Separately)
-'
Program
SWC
;
Interf
ace
for
Version
2.
\.
Installation
Notes
1.
Only one
of
the two provided radio harnesses will be used. Remove the factory
installed radio to determine the correct harness for your particular vehicle.
2.
Vehicles
without
a
factory
amplifier: Connect the aftermarket radio's front and
rear speaker wires to the 22 pin plug.
SWC Output
Blue I White Amp Turn On Input
3.
Vehicles
with
a
factory
amplifier:
The factory amplifier only accepts two audio
channels (left and right). The amplifier's fading
is
controlled by data communication
from the factory radio. The aftermarket radio does not have the ability to control the
amplifier's fader. Connect the
front
outputs
of
theaftermarket
radio
to the
rear
inputs
of
the
22
pin
radio
connector. This will
allow navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs
of
the aftermarket radio are not used.
4. The accessory outputwire is located on the
11
pin CAN INTERFACE harness -connectthis wire to the radio's accessorywire. The
accessory wire supplies +12v, 1 amp max when key is in the accessory
or
ignition position (fig.
1:
Ifmore current
is
needed).
5.
11
pin
plug
(to
CAN INTERFACE):
1.
Blue/White -Connect this wire to the radio's amplifier remote output. Connect this wire with
or
without OEM amp present!
2.
White/Green -SWC output.
3.
Green -Connect this wire to the radio's reverse input wire only.
4. Orange/White -Connect this wire to the radio's Illumination input wire only.
5.
Violet/White- Connect this wire to the radio's VSS input wire only.
6.
Red/White -Connect this wire to the radio's parking brake input wire only.
Note: Do
not
connect
these
wires
to
any
circuit
other
than
the
radio's
wire
harness.
6.
11
pin
plug
(to
SWC INTERFACE):
This
is
a quick connection to a radio specific SWC interface. No additional
connections are necessary other than radio control connections. Plug the radio
specific SWC interface in to this connector and program the radio specific SWC
interfaceforversion 2. Do notcutthe loops. Referto the SWC interface instruction
manual for the radio specific control function programming order.
Fig. 1
(using a SPDT
re
lay)
12vAce.
or equivel
ant
High
Current
12v
(Fused)
Ground
7. Referto the aftermarket radio's instruction manual fortesting VSS, Reverse, Parking Brake and Illumination outputs. For the most
current and Up-to-Date application guide please visit www.pac-audio.com
7-19-10
PacificAccessory Corporation- Ontario California, 91761
[e-mail] • www.pac-audio.com

Us
in!!
the YES
&
RcYerse Camera
if
ec
ui
JJed
Vehicles equipped with a DVD player built into the rear screen assembly:
The C2R-CHY4 will allow the VES DVD player and rear screen to function as
if
the factory radio were present.
AN
will be passed
from the factory DVD player to the rear screen and audio can be heard through the headphones.
AN
cannot be passed from the
factory DVD player to the aftermarket head unit.
Vehicles equipped with a stand alone VES DVD Player:
The C2R-CHY4 will allow the VES DVD player and rear screen(s) to function as
if
the factory radio were present.
AN
will be
passed from the factory DVD player to the rear screen(s) and audio can be heard through the headphones.
AN
can also be fed
from the VES DVD player into an aftermarket head unit (head unit must support
AN
in) with the use
of
the CHYRVD.
Vehicles not equipped with
aVES
DVD Player (rear screen(s) only):
In this application the CHYRVD must be used
in
orderto feed
AN
into the factory screen(s) from an aftermarket head unit (head
unit mustsupport
AN
out). With the CHYRVD,
AN
will be passed from the aftermarket head unit to the rear screen(s) and audio
can
be
heard through the headphones.
If
you wish to retain the Auxiliary inputs on the rear
of
the console you must disconnect the
factory wires from the auxiliary input then connect and run your own RCAs into the aftermarkethead unit.
Vehicles equipped with a Reverse Camera:
In order to retain the factory reverse camera the CHYRVD must
be
used to feed video into the aftermarket head unit (head unit
must support reverse camera input).
DISCLAIMER: Under
no
circumstances
shall
the
manufacturer
or
the
distributors
of
the C2R-CHY4 be held liable
for
consequential damages sustained
in
connection
with
the
C2R-CHY4. The manufacture and it's
distributors
will not,
nor
will
they
authorize
any
representative
or
any
other
individual
to
assume
obligation
or
liability
in
relation
to
the
C2R-CHY4 other
than
its
replacement.
7-19-10 PacificAccessory Corporation
-Ontario
California, 91761
[email protected] • www.pac-audio.com

Provides Navigation Outputs anll
Factory Amplifier if EIIUilll

PAC2C4v1
UpJraded
Aftermarket
Radio
Provides
Navigation
Outputs
and
Retains
Factory
Amplifier
it
Equipped
Your
Comflatillle
Automobile
This product allows the replacement of your automobile's original factory radio with
an
upgraded aftermarket
radio. It has been engineered to seamlessly interface with the automobile's computer data-bus system and
provide necessary outputs for installation
of
an
aftermarket navigation radio. Retains operation offactory
installed amplifier (if equipped).
'
This interface
is
compatible with select years and models from the following manufacturers:
Dodge, Chrysler, and Jeep
To
learn whether or not your specific automobile
is
compatible, visit www.pac-audio.com.